ARMY MIL-F-51531 A-1991 FLUID CONTAINER FILLED (FOR M13 DECONTAMINATING APPARATUS)《含流体的容器(用于M13去污器具)》.pdf

1、I .Q - 1- - MIL-F-51531A 42 9799906 0500672 1 MIL-F-51531A(EA) - SUPERSEDING MIL-F-5 15 3 1 (EA) 13 December 1989 MILITARY SPECIFICATION FLUID CONTAINER, FILLED (FOR M13 DECONTAMINATING APPARATUS) This specification is approved for use by the U.S. Army Chemical Research, Development and Engineering

2、Center, Department of the Army, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers one type of filled fluid container which provides 14 liters of decontaminating agent for dispensing. 2. APPLICABLE DOCUMENTS 2.1 Govern

3、ment documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, stan- dards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Depart- ment of Defense

4、 Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander, U.S. Army Chemical Researc

5、h, Development and Engineering Center, ATN: SMCCR-PET-S, Aberdeen Proving Ground, MD 2 10 10-5423 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC NIA FSC 4230 DISTRIBUTION STATEMENT A. Approved for publ

6、ic release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-F-SL53LA 42 999990b 0500673 3 MIL-F-5 1 5 3 1 A(EA) . e SPECIFICATIONS FEDERAL BB-N-4 1 1 - Nitrogen, Technical MILITARY MIL-D-50030 - Decontaminating Agent, D

7、S2 STANDARDS MILITARY MIL-STD-1168 - Ammunition Lot Numbering (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 191 11-5094.) 2.1.2 Other

8、Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicita- tion. U.S. ARMY CHEMICAL RESEARCH, DEVELOPMENT A

9、ND ENGINEERING CENTER DRAWINGS 5-51-575 - Fluid Container, Filled SPECIAL PACKAGING INSTRUCTIONS (SPI) P5-51-575 - Fluid Container, Filled QUluid container, filled CLASSIFICATION OF CHARACTERISTICS I I DRAWING NUMBER CHARACTERISTIC Leakage Container fill Chemical and physical characteristic Specifie

10、d components correctly Closures torque correct Nitrogen purge correct Heat shrinkable tubing correctly Protective finish evident of DS2 assembled applied Labels evident, correct and Workmanship correctly assembled NOTES: CE - Commercial inspection equipment VI - Visual inspection * Destructive test

11、SAMPLING AND ACCEPTANCE CRITERIA 100 percent 100 percent Table I, Level IX Table I, Level WI Table I, Level VII Table I, Level WI Table I, Level W Table I, Level W Table I, Level IX Table I, Level IX EQUIREMENl PARAGRAPH 3.3 3.2.3 3.2.4 5.1.2 3.1.2 3.2.2 3.1.2 3.1.2 3.1.2 3.7 INSPECTION METHOD 4.4.6

12、.3 4.4.6.1 4.4.6.2“ VI CE VI VI VI VI VI 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-PARAGRAPH 4.4.5 (b) CATEGORY Critical Major 101 102 103 104 105 106 107 108 Minor 201 202 203 VOTES: MIL-F-51531A 42 9999906 0500683 2 = MIGF- 5 1 5 3 1 A(EA)

13、CLASSIFICATION OF CHARACTERISTICS TITLE Fluid container assembly CHARACTERISTIC None defined Lifting handle strength Burst strength Leakage Drop strength Weldments correct Height dimension Length, width and radius dimension Protective finish evident correct Specified components correctly Labels evid

14、ent, correct and correctly Workmanship assembled located CE - Commercial inspection equipment VI - Visual inspection * Destructive test *Any container that leaks shall be rejected. SAMPLING AND ACCEPTANCE CRITERIA 5; Acc O, Rej 1 5; Acc O, Rej 1 100 percent* Table I, Level X Table I, Level W Table I

15、, Level W Table I, Level W Table I, Level W able I, Level IX able I, Level IX able I, Level W 15-5 1-575 IEQUIREMENl PARAGRAPH 3.4.1 3.4.2 3.4.3 3.4.4 3.1.2 3.1.2 3.1.2 3.1.2 3.1.2 3.1.2 3.7 INSPECTION METHOD 4.4.6.4.1 4.4.6.4.2* 4.4.6.4.3 4.4.6.4.4* VI and CE CE CE VI VI VI VI Provided by IHSNot fo

16、r ResaleNo reproduction or networking permitted without license from IHS-,-,-ARAGRAPH .4.5 (c) ITLE op reservoir assy SHEET OF CATEGORY DRAWING NUMBER 5-5 1-523 NEXTHIGHERASSY 5-5 1-538 Critical Major 101 102 103 104 Minor 201 flIL-F-5153LA 42 9999906 0500682 4 MIL-F-5 15 3 lA(EA) CHARACTERISTIC rTo

17、ne defined Ack clip location correct Lifting handle location correct Veld and braze correct Lifting handle strength+ Workmanship SAMPLING AND ACCEPTANCE CRITERIA rable I, Level VII able I, Level W rable I, Level VII 5; Acc O, Rej 1 rabie I, Level IX EQUIREMENl PARAQRAPH 3.1.2 3.1.2 3.1.2 3.4.1 3.7 I

18、NSPECTION METHOD CE CE VI 4.4.6.4.1 VI NOTES: CE - Commercial inspection equipment VI - Visual inspection * Alternate test; test shall be imposed either as above or in accordance with 4.4.5(b), Category Major 101 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license

19、 from IHS-,-,-ARAGRAPH I. 4.5 (d) CATEGORY Critical Major 101 102 NIL-F-SL53LA 42 H 9999906 0500683 b MIL-F-51531A(EA) CLASSIFICATION OF CHARACTERISTICS ITLE lug assembly I 1 DRAWING NUMBER I SHEET OF w NEXT HIGHERASSY I 15-51-538 CHARACTERISTIC None defined Leakage Specified components undamaged an

20、d correctly assembled NOTES: CE - Commercial inspection equipment VI - Visual inspection SAMPLING AND ACCEPTANCE CRITERIA 5; Acc O, Rej 1 rable I, Level w IEQUIREMENl PARAGRAPH 3.5 3.1.2 INSPECTION METHOD 4.4.6.5 VI 12 Provided by IHSNot for ResaleNo reproduction or networking permitted without lice

21、nse from IHS-,-,- ARAGRAPH 1.4.5(e) CATEGORY Critical Major 103 102 103 Minor 201 MIL-F-51531A 42 9999906 0.500684 a MIL-F-5 15 3 1 AEA) CLASSIFICATION OF CHARACTERISTICS ITLE idapter assy I I DRAWING NUMBER I SHEET 1 OF 1 1- NEXT HIGHER ASSY CHARACTERISTIC None defined Specified components correctl

22、y assembled Length Welding correct Workmanship NOTES: CE - Commercial inspection equipment Vi - Visual inspection I 15-51-523 SAMPLING AND ACCEPTANCE CRITERIA able I, Level W able I, Level W able I, Level W able I, Level Ix IEQUIREMENl PARAGRAPH 3.1.2 3.1.2 3.1.2 3.7 INSPECTION METHOD VI CE CE VI 13

23、 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-PARAGRAPH 4.4.5 (f) CATEGORY Critical Major 101 102 Minor 201 202 NOTES: - iI MIL-F-SL53LA 42 61979906 0500645 T MIL-F-5 1 5 3 1 A(EA) TITLE 4dapter assy CLASSIFICATION OF CHARACTERISTICS I I DRAWING N

24、UMBER I OF I=- NEXTHIGHERASSY I 15-51-523 CHARACTERISTIC None defined Specified components correctly assembled Brazing correct Workmanship Crimped end opening correct CE - Commercial inspection equipment VI - Visual inspection SAMPLING AND ACCEPTANCE CRITERIA able Leve TI rable I, Level VII rable I,

25、 Level IX rable I, Level IX IEQUIREMENl PARAGRAPH 3.1.2 3.1.2 3.7 3.1.2 INSPECTION METHOD VI VI VI VI 14 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-PARAGRAPH 4.4.5 (g) CATEGORY Critical Major 101 102 103 104 105 106 107 Minor 201 NOTES : - MIL-F

26、-51531A 42 W 979990b 05006b L 0 TITLE Packaging - Packing - Palletization CLASSIFICATION OF CHARACTERISTICS I I DRAWING NUMBER SHEET OF NEXT HIGHER ASSY I CHARACTERISTIC None defined Item completely clean and dry Fiberboard pads evident and correct Unit pack container and closure evident and correct

27、 Unit pack container marking evident, correct and undamaged Shipping container and closure correct and undamaged Special markings evident, correct and legible Banding straps evident and undamaged prior to unit packing Pallet correct and undamaged CE - Commercial inspection equipment VI - Visual insp

28、ection SAMPLING AND ACCEPTANCE CRITERIA able I, Level W able I, Level W able I, Level W able I, Level W able I, Level W able I, Level W able I, Level W able I, Level W rable I, Level IX IEQUIREMENT PARAGRAPH 5.2 5.2 5.2 5.2 5.2 5.2 5.2 5.2 5.2 INSPECTION METHOD VI VI and CE VI and CE VI and CE VI an

29、d CE VI and CE VI and CE VI and CE VI and CE 15 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-F-SL53LA 42 7777706 0500687 3 H MIL-F-5 15 3 1A(EA) 4.4.6 Tests (see 6.4). Unless otherwise specified, tests shall be performed at room temperature, 2

30、0“ to 30C (68“ to 86“F), as follows: 4.4.6.1 Container fill. Weigh the container before and after filling to determine fill weight. 4.4.6.2 Chemical and physical characteristics of DS2. Take a 1-liter specimen of DS2 from the filled fluid container and immediately test in accordance with the tests f

31、or Chemical and physical characteristics requirements specified in MIL-D-50030 (see 6.4). 4.4.6.3 Leakage. Place the filled closed container, without coupling cap and heat shrink- able tubing, on a side under water in a vacuum chamber so that no more than 1-inch of water covers the container (see 6.

32、6). The water shall contain phenolphthalein (0.5 percent by weight phenolphthalein in methanol diluted to 10 milliliters of methanol per liter of water having a pH of 6.5 to 7.5). The filled container and water shall be at ambient temperature. Reduce the pressure in the vacuum chamber to 87 millimet

33、ers of mercury or less absolute. Hold the vacuum for at least 1-minute and observe the seams and threaded areas of the container for bubbles and pink coloration of the water. Any bubbles or pink coloration of the water at the seams or threaded areas of the container shall be considered evidence of l

34、eakage, 4.4.6.4 Fluid container assembly (Drawing 5-51-538). 4.4.6.4.1 Lifting handle strength. Secure the top reservoir or the container assembly and apply the specified static load uniformly over the handle for the specified time. Examine lifting handle and top-reservoir, or lifting handle and con

35、tainer assembly as applicable. 4.4.6.4.2 Burst strength. Plug all openings to affect a seal within the fluid container. Attach a source of hydrostatic pressure into the container through a fitting and apply the specified hydrostatic pressure for the specified time. Note: The container sides may be s

36、upported in a fixture during this test. See 6.7 for precautions regarding high pressure. 4.4.6.4.3 Leakage. With the fluid container openings sealed and with the specified air pressure introduced into the container through a fitting, submerge the container in water con- taining a wetting agent to a

37、depth of no more than 3 inches below the surface for the specified time and observe for leakage. A steady stream of bubbles shall be an indication of leakage. 4.4.6.4.4 Drop strength. Fill the container with water and seal in accordance with note 4, Drawing 5-51-575. Drop the container as specified

38、on bottom seam diagonally opposite from the ventlcoupling area. 16 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-F-51531A 42 9999706 05006 5 MIL-F-5 15 3 lA(EA) 4.4.6.5 Plug assembly leakage (Drawing 5-51-578). Attdch a source of air pressure t

39、hrough an airtight fitting to the open end of plug assembly and apply specified air pressure. Submerge assembly in water to a depth of no more than 3 inches and examine for leakage for the specified time. A steady stream of bubbles shall be an indication of leakage. e 5. PACKAGING 5.1 Interplant shi

40、pment (see 6.8). Military packaging as specified in 5.2 is not applica- ble for interplant shipment. The filled fluid container shall be packaged and marked to provide adequate protection from physical damage from the supply source to the first receiv- ing activity for immediate use or further proce

41、ssing. Shipping containers shall be in compli- ance with the rules and regulations applicable to the mode of transportation. 5.2 Repair or replacement parts. For all shipments, other than interplant shipments (see 6.8), packaging (preservation, unit packing, packing and marking) shall be as specifie

42、d in SPI P5-51-575. 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is. not mandatory.) 6.1 Intended use. The filled fluid container is intended to be used as a major component of the M13 Portable, 14 Liter, Decontaminating Apparatus which is u

43、sed for dispensing DS2 decontaminating agent in the field. 6.2 Acquisition requirements. Acquisition documents must specify the following: (a) Title, number, and date of this specification (b) Issue of DODISS to be cited in the solicitation, and if required, the specific issue (c) First article: of

44、individual documents referenced (see 2.1.1). (1) First Article Inspection and Report requirements. (2) Delivery schedule for First Article Report. (3) Destination and delivery schedule of First Article Samples when testing is (4) First Article Test report approval time. performed by the Government.

45、(d) Production (1) Destination and delivery schedule requirements. (2) Production and inspection report requirements. 17 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-HIL-F-5L53LA 42 H 9999906 0500689 i MIL-F-5 15 3 1 A(EA) (e) Shelf life code (see

46、 section 5). (f) Palletization required (see 5.2). 6.3 Submission of alternative inspection provisions. Proposed alternative inspection provisions should be submitted by the contractor to the procuring contracting officer for evaluation and approval by the technical activity responsible for preparat

47、ion of this specifi- cation. 6.4 Sampling, testing, handling precautions for DS2. Warning: DS2 is a combustible liquid (Flash Point 168F) and should not be stored near open flames or heat sources. DS2 is classified as a corrosive liquid as it contains sodium hydroxide and diethylenetriamine which ar

48、e caustic in nature. DS2 is a toxic chemical with an ammonia-like odor and should be handled in a well ventilated environment and with appropriate protective clothing and equipment (Le. corrosive resistant gloves, boots, apron, an industrial faceshield or splash- proof chemical goggles, and full fac

49、epiece respirator with amine cartridge). Use copious amounts of water for eye or skin contact. If DS2 is ingested, administer as much milk or water as possible, but do not induce vomiting. Spills should be neutralized with sodium bisulfate, absorbed with vermiculite and containerized as quickly as possible. Fires involv- ing DS2 can be extin