ARMY MIL-S-14642 A-1980 SHOULDER BOARD AFROTC CADETS《AFROTC学员肩章》.pdf

1、MIL-S-14642A 84 7797706 0377014 3 H c4s445 MIL-S-14642A 12 May 1980 Superseding MIL-S-0014642 (IH) 15 November 1974 MILITARY SPECIFICATION .s SHOULDER BOARD AFROTC .CADETS 1.1. Scope-This specification covers one type of shoulder board in two styles for use by AFROTC cadets. 1.2 the following styles

2、 (see 6.2): Classification-Shoulder boards covered by this specification shall be of Style l-Ffale Style 2-Female 1.2.1 or 6.3). Ribbon-The size of the ribbon shall be 1/2 inch for both styles (see 6.2 2. APPLICABLE DOCUMENTS 2.1 The following documents of the issue in. effect on date of invitation

3、for bids or request for proposal, form a part of this specification to the extent spec if i ed here in. SPECIFICATIONS FEDERAL C-F-206-Felt Sheet: UU-P-268-Paper, Kraft , Wrapping . V-T-2 76-Thread, Cotton Cloth, Felt, Wool, Pressed Provided by IHSNot for ResaleNo reproduction or networking permitte

4、d without license from IHS-,-,-MIL-S-146Ll2A 4 7797706 0377035 5 MIL-s-1464 2A PPP-B-676-Boxes, Setup PPP-B-636-Box, Shipping Fiberboard PPP-T-60 -Tape, Packaging, Waterproof MILITARY MIL-B-3461 -Buttons, Insignia, Metal, Uniform and- Cap MIL-S-3951-Service Ribbons and Bars, Service Ribbon STANDARDS

5、 MILITARY MIL-STD-l05-Sampling Procedures and Tables for Inspection by Attributes MIL-STD-l29-Marking for Shipment and Storage DRAWING THE INSTITUTE OF HERALDRY B-10-11 -Shoulder Boards, AFROTC (Copies of specifications, standards and drawings required by suppliers in connection with specific procur

6、ement functions should be obtained from the procuring activity or as directed by the contracting officer. Figure 2. is a miniature reproduction of drawing B-10-11 and is attached for information purposes.) 2.2 Other publications-The following standard forms a part of this specifica- tion to the exte

7、nt specified herein. Unless otherwise specified, the issue in effect on date of invitationfor bids or request for proposal shall apply: THE COLOR ASSOCIATION OF THE UNITED STATES, INC. US Army Color Card, The Official Colors for Branches, Agencies, etc. 2 Provided by IHSNot for ResaleNo reproduction

8、 or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-14642A 3.2.9.1.2 Filling-The filling shall b

9、e a silver color mylar plied with a nylon supporting yarn and shall be equivalent to number 1.2 Laminette. yarn shall be approximately 420 denier, 00085 inches in diameter and round. The filling 3.3 Drawing B-10-11. Design-The design of the shoulder board shall be in accordance with 3.4 Construction

10、-The spine of the shoulder board (see 3.2.8) shall be formed and the front covered with felt specified in 382.1. The felt shall extend onto the back, at least 3/4 inch around. cement specified in 3.2.3. The ribbon bar specified in 3.2.5 shall be centered on and cemented to the bottom of the spine. T

11、he back of the shoulder board shall be covered with backing cloth (see 3.2.2) lined with paperboard specified in 3.2.7. covered with backing cloth specified in 3.2.2. cemented to the paperboard and stitched to the felt covering. The button specified in 3.2.6 shall be mounted in the position shown. s

12、ecured to the shoulder board by riveting or any method suitable to the contracting officer (see 6.2). The felt shall be glued to the spine with .The face and 1/2 inch of the back edges of the paperboard shall be The backing cloth shall be The button may be 38 4.1 Stitching-The backing cloth shall be

13、 secured to the felt by hand stitching using thread Specified in 3.2.4 with a minimum of 8 stitches to the inch. 3.5 acceptable quality levels established by this specification. Workmanship-Shoulder board shall be clean, well made, and shall meet the Provided by IHSNot for ResaleNo reproduction or n

14、etworking permitted without license from IHS-,-,-MIL-S-34642A 4 7777706 0377037 2 MIL-S- 146 4 2A 4. QUALITY ASSURANCE PKOVISIONS. 4.1 Responsibility for .inspection-Unless otherwise specified in the contract or order, the supplier is responsible for the performance of all inspection requirements as

15、 specified herein. Except as otherwise specified in the contract . or purchase order, the supplier may use his own or any other facilities suitable for the performance of inspection requirements specified herein, unless dis- approved by the Government. the inspection set forth ia the specification w

16、here such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. The Government reserves the right to perform any of 4.2 First article inspection-When first articles are required, inspection and testing of the first article shall be made on a completely

17、fabricated shoulder board for all provisions of this specification applicable to the end product examination and tests. 4.3 MIL-STD-105 except where otherwise indicated. 4.3.1 Inspection for acceptance-Inspection shall be in accordance with Testing of components-In addition to the quality assurance

18、provisions of subsidiary specifications and drawings, components shall be tested as specified in table II. When the data in the “Number of determinations per sample unit“ and “Results reported as“ columns are not specified in table 11, they shall be as required by the referenced test method. All req

19、uirements are applicable for the individual sample unit. The inspection level shall be S-1 and the acceptable quality level for sample unit requirements shall be 6.5 defects per hundred units. The sample unit for the tests in table II shall be as follows: 6 Provided by IHSNot for ResaleNo reproducti

20、on or networking permitted without license from IHS-,-,-Component 1 .Characteristic I Para I I Wool Felt for I I I I cover I Colorfastness to: I I I I Wet-Dry Gleaning I 3.2.1 I I I Crocking I 3.2.1 I I 3.2.1 I I Light I 3.2.1 . I I I I I Colorfastness to: I I I I Wet-Dry Cleaning I 3.2.2 I I Crocki

21、ng I 3.2.2 I .I I Light I 3.2.2 I I Water I 3.2.2 I I I I I I Picks per inch Table I I I I Thickness I I I Tab1.e I I I 302.9- I Weave . I I I I I I I, I I Thickness . 1 3.2.8 . I *.$ I I Water Backing Cloth I Ribbon I Material Indent. I 3.2.9.1.1 I and 1 I 342*9*1-2 I I Weight Aluminum I Material I

22、ndent. I 3.2.8 I Thickness I 3.2.8 Fiberboard I .Material Indent. I 3.2.8 I I I I 565 1 I I 5660 I I 5630 I I I I I I 5622 I I 565 1 I I 5660 I I 5630 I 5622 I II Std Coml I Visiai I Visual I Visual I Std Coml I 1 Std Coml I Std Coml I 111 I 504 1 I I Std Coml II/ I Test I per unit I Results Method

23、I of Product I Reported as I I I I. I I I I I I Pass or Fail I I Pass or Fail I I Pass or Fail I I Pass or Fail I I I I I I Pass or Fail -I I Pass or Fail I I Pass or Fail I I Pass or Fail I I I I Pass or Fail .I I Pass or Fail I I Pass or Fail I I Pass or Fail I I Pass or Fail I I Pass or Fail 1 I

24、Pass or Fail I I Pass or Fail I I Pass or Fail Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-14b42A 84 993370b 0379022 - 2 MIL-S-14642A 4.3.2.2

25、Defects in dimensions-Any dimension not within the specified tolerance shall be classified a defect. The acceptable quality level shall be 2.5 defects per hundred units and the inspection level shall be S-3. The sample unit shall be one finished shoulder board. 4.3.2.3 shall be classified in accorda

26、nce with the lists shown in 4.3.2.4, 4.3.2.5, and 4.3.2.6. 4.3.2.4 Visual examination of ribbon-Defects found during the examination Yard-by-yard examination-The required yardage of. each roll shall be inspected and visual defects classified as listed. A continuous defect shall be counted as one def

27、ect for each warpwise yard or fraction thereof in which it occurs. The sample unit shall be one linear yard. The sample size shall he based upon inspection level II. The lot size shall be expressed in units of one linear yard. The number of rolls from which the sample is to be selected shall be in a

28、ccordance with Table III. be examined in each roll. An approximately equal number of yards shall The acceptable quaiity level shall be 4.0 defects per 100 units. Defects Hold, cut, or tear. Broken or missing yarn. Float or skip. Open place or crack, Thick or thin area filling wise. Incorrect weave i

29、n pattern. Spot, stain, or streak. Overall width less than specified. Overall width more than specified. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I_- MIL-S-LYb42A 4 W 7999906 0377023 4 MIL- S-14642A 4.3.2.5 Overall examination-Each defect list

30、ed shall be counted not more than once in each roll examined. The sample unit shall be one roll. The number of rolls selected for yard-by-yard examination shall comprise the sample selected for this examination and the number of defects acceptable shall be as specified in table III. Defects Soiled t

31、hroughout Finish other than specified. Selvage curled, folded, rolled, slack or sloppy, torn continuously or intermittently over more than one-half the roll. TABLE III-ACCEPTABLE NUIBER OF DEFECTS Maximum Number of Defects Applicable . Lot S.ize in Yards Sample Size in Rollq to Sample 1/ Up to 1,300

32、- 1,301 to 3,200 3,201 to 8,000 8,001 to 22,000 22,001 to 110,000 110,001 and up 3 5 7 10 15 25 LIf lot contains fewer than 3 rolls., each roll in the lot shall be examined. 4.3.2.6 Examina.tion for Length- 4.3.2.6.1 Individual Rolls-The roll shall be examined for gross length and number and length

33、of pieces on the roll. Any gross length found to be less than the minimum specified or more than 2 yards below the gross length marked on the roll shall be considered a defect with respect to length. this examination shall be one roll. The number of rolls selected as sample The sample unit for (samp

34、le size) for this examination and the acceptance number shall be in accordance with Table III. 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-14642A 4 = 7777906 0377024 b U MIL-S-14642A 4.3.2.6.2 Total yardage in campLe-The lot shall be una

35、cceptable if the total of the actual gross lengths of the rolls in the sample is less than the total of the gross lengths marked on the rolls. 4.3.3 Examination of preparation for delivery requirements-An examination shall be made to determine that packaging, packing and marking requirements of sect

36、ion 5 of this specification are complied with and defects shall be scored in accordance with the list below. package, selected just prior to the closing operation. Defects of closure listed below shall be examined on shipping containers fully prepared for delivery. The lot size shall be the number o

37、f containers in the inspection lot. The inspection level shall be S-2 and the AQL shall he 2.5 defects per hundred units. The samele unit shall be one shipping container fully Defect - Examine Harking (exterior and interior) Omitted, incorrect, illegible, or . improper size, location sequence, or fa

38、terials hrorkmanshi p Contents Weight method of application. Any component missing. * Any component damaged, affecting service- ability. Inadequate application of components, such as, incomplete closure of case liners, container flaps, loose strap- ing, inadequate stapling. Number per container is m

39、ore or less than r equi red . Net weight exceeds permissible maximum. 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo

40、 reproduction or networking permitted without license from IHS-,-,-MIL-S-L4bi.I2A 8i.I 7779706 0377027 L , MIL-S-14642A f. Selection of applicable level of packaging and packing (see 5.1 and 5.2). 6.3 Combination of metallic ribbon shall be anchored to the shoulder board at the unit level to disting

41、uish individual grade, but should be procured as a separate item for issue. Custodians : Air Force-11 Review Activities: Air Force-99 DLA-CT Project No. 8455-0845 Preparing Ac ti vit y : The Institute of Heraldry, United States Army Provided by IHSNot for ResaleNo reproduction or networking permitte

42、d without license from IHS-,-,-MIL-S-14642A 4 7779906 0379028 3 MIL-S-14642A O O rl 15 I v) lil FIGURE 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-4949906 0374024 5 M B p 4 c 16 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-