ARMY MIL-T-3187-1950 TRAINER GUNNERY TANK 75-MM M14《M1型590mm坦克航炮训练员》.pdf

1、MIL-T-3187 27 APRIL 1950 MILITARY SPECIFICATION TRAINER, GUNNERY, TANK, 75-MM, M14 Thk spectflcation was approvea by-the Department8 of the Amt.!, the Nauy, and ths Air Force for use of the procurement 8ervbe.s of the respective Depwtmmts 1. SCOPE 1.1 This specification covers one type of trainer fo

2、r use in the preliminary instruction of the United States Armed Forces in the use and maintenance of the 75-m tank gun, M6. The trainer is designated Traber, Gunnery, Tank, 7i-MM, M14. 2. APPLICABLE SP E CI FI CATIONS AND DRAWIFGS 2.1 Specifications.-The following spec=- cations and all specificatio

3、ns referred to on the drawings specified in 2.5 of the issue in effect on date of invitation for bids, form a part of this specification : hDERAL SPECD?IUATIONS TT-E-48li-Enamel; (for) Drums and other Metal Products, Rust-Inhibiting, Olive Drab. W-EL489-Enamel; loss, Synthetic (For Exterior and Inte

4、rior Surfaces). TT-P-636-Prher, Paint j Synthetic (For Ferrous Metal and Wood Surfaces), n-p-659-Primer-Surf awr ; Synthetic, Tints and Whits (For Metal and Wood Hospital Furniture). ARY SJ?EGIFICATIONS W-M-561-Motor-Fuel M. MIL-G-305 General Requirements for. 60-8%24-Mount, Gun, Combination, M64. 6

5、0-89-7-Seats, Combat Vehicle, General 60-9Gl-Stabilizer, Gun, Gyroscopic. 60-984-%Mechanism, Traversing, Turret, 91-8 High-Tension. AXS-1851-Starters; Direct Cranking, Waterproof, %-Volt, D. C. (Copies of specifications should be obtained from the procuring agency or as directed by that agency. Both

6、 the title and identifying number or symbol shonld be stipulated when requesting copies.) 2.2 Drawings.-All drawings listed in Ord- nance Department Engineering Parta List No. 7714454, of the issue in effect on date of invita- tion for bids, form a part of this specifwation. (Copies of drawings shou

7、ld be obtained from the procuring agency or as directed by that agency. Both the title and identifying number or symbol should be stipulated when requesting copies.) Requirements for. Hydraulic. Motor Vehicles. for Tank and Automotive Materiel. ing Shipments by Contractors. FICATIONS Automotive). Wa

8、terproof. 3. REQUIREMENTS 3.1 Materials.-The materials used in the manufacture of the trainer Units shall be in Licensed by Information Handling ServicesMIL-T-3187 b7 W 777770b 0373607 O W MILT-3187 accordance with Specification 60-0-1 and a8 hereinafter specified. Unless otherwise speci- fied, mate

9、rials or equipment designated on the applicable drawings as (commercial” shall be the best quality available. They shall be suit- able for the intended purpose, and shall be free of def wts which may affect their serviceability or appearance. 3.2 Performance.-The trainer units, fully assembled, shal

10、l function properly in all details, as determined by the tests prescribed in section 4. 3.3 Components. - The complete trainer shall consist basically of a modified tank turret unit and a power unit, with each unit mounted on a separate dolly. 3.4 Turret unit. 3.4.1 Tumet doZly.-The turret dolly sha

11、ll be a table-like structure consisting of a ring- shaped top surface to permit the attachment of the turret ring gear, and legs mounted on cast- ers to permit it to be moved about. The dolly structure shall be adequately reinforced so as to develop the required strength to support the turret with g

12、un and gun mount inst.alled, and an additional weight of approximately 3,000 pounds as represented by observers standing on the observation platforms. (See 3.4.6.) A shield, fabricated of expanded metal, shall com- pletely encircle the dolly as shown on the ap- plicable drawings. 3.42 Casters.-The t

13、urret dolly shall be provided with two rigid (nonswiveling) and four swivel casters bolted to the dolly legs as shown on the applicable drawings, The casters shall have sufficient capacity to support the combined weight of the dolly, turret, and per- sonnel as specified in 3.4.1. 3.4.2.1 Wheels and

14、mles.-The caster wheels shall be fabricated of metal and shall be mounted on axles of the bolt and nut type. A suitable means shall be provided to prevent the nut from unscrewing. 3.4.2.2 Bea4ngs.-Wheels shall be mounted on antifriction bearings of the ball or roller type. Swivel type casters shall

15、be provided with antifriction bearings in the swivel. The balls or rollers shall be of chrome nickel steel and the races shall be ground. 3.4.2.3 Forks,-The caster forks shall be so .- designed as to minimize the possibility of the caster wheels rubbing or binding between the arms. 3.4.3 Jach.-The t

16、urret dolly shall be pro- vided with three leveling jacks positioned as shown on the applicable drawings. Each jack shall consist basically of a threaded barrel and screw, and a base. Suitable means shall be pro- vided in the screws for raising or lowering the jacks. 3.4.4 Twet.-The turret shall be

17、mounted on the turret dolly as shown on the applicable drawings. The turret, after mounting, shall be closely adjusted to provide proper operation through 360 of rotation without interference and without lost motion exceeding that per- mitted on the applicable drawings. With the turret assembly ring

18、 gear fuqy bolted to the dolly, and with the turret complete with gun, gun mount, and slip ring installed, but without hand and hydraulic traversing mechanisms in- stalled, torque required to maintain rotation of the turret with the dolly in a level position shall not exceed 300 foot-pounds. Variati

19、on between maximum and minimum torque through 360 of rotation shall not exceed 50 foot-pounds. 3.4.5 Traversing mechanism.-The turret shall be provided with a traversing mechanism conforming to Specification 60-9862 and to the applicable drawings, 3.4.6 Observation pZatfomns.-The turret shall be pro

20、vided with two observation plat- forms, one on each side of and securely attached to the turret. Each platform shall be rigidly constructed so as to be capable of supporting a weight of approximately 1,500 pounds. The platform shall be provided with suitable hand- rails as shown on the applicable dr

21、awings. 3.4.7 Gun mount.-The gun mount shall conform to Specification 60-82-24 and to the applicable drawings. 3.4.8 Gum stabiliaer.-The gun stabilizer shall conform to Specification 60-9861 and to the applicable drawings. 3.4.9 Sighting and visSion dehe mount- ings.-Mountings for fire-control instr

22、uments, periscopes, and similar devices shall conform to the applicable drawings, and shall be so in- 2 Licensed by Information Handling Services, MIL-T-3L7 67 7977706 0373bO 2 M. - stalled as to function freely, without deflection beyond prescribed limits. 3.4.10 Communication s ystem.-Provkions sh

23、all be made for installation of radio and in- terphone systems in accordance with the appli- cable drawings. 3.4.11 8eats.-The turret shall be provided with three cushioned seats conforming to Speci- fication 60-89-7, and to the applicable draw- ings. 3.4.12 Ammunition rach and stowage except that t

24、he in- terior of the turret shall receive one coat of white gloss enamel conforming to Specification 3.7.3 Ifiaccess6le szcrf aces.-Sur f aces inac- cessible for painting after assembly shall be painted while apart. 3.8 Lubrication.-Turret and power units shall be thoroughly lubricated after assembl

25、y. Lubricating fittings shall permit free passage of the lubricant to all bearing areas. Antifric- tion bearings shall be properly packed with grease before assembly. All lubricants shall conform to applicable speciications, and shall be of the grade recommended (see 6.2) for use by the Department o

26、f the Army. 3.9 Workmanship.-The workmanship shall be of the quality necessary to produce trainer units free of defects which may affect service- ability or appearance, and shall comply with the applicable requirements of Specification 60-0-1. 3.9.1 Welding.-All welds shall be sound and smooth, free

27、 of porosity, cracks, or incom- plete fusion, deformation of the metal, and rough or projecting edges. Defects in parts or materials shall be repair-welded only when specifically authorized by the procuring agency. 3.9.2 Finjshed szcrfaces.-All finished sur- f aces shall be protected to prevent corr

28、osion and injury during manufacture and until de- livery. Fins and other extra metal shall b TT-E-489. removed from castings and forgings. Func- tioning surfaces shall be smooth and free of burrs. 3.9.3 Intevc and the fact that the Government may have formulated, furnished, or in any way supplied th

29、e said drawings, specifications, or other data is not to be regarded by implication or otherwise as in any manner licensing the holder or any other person or corporation, or conveying any rights or permission to manufacture, use, or sell any patented invention that may in any may be related thereto. Custodian: Army-Ordnance Department. 6 Licensed by Information Handling Services