ARMY MIL-T-43497 D-1988 TROUSERS COLD WEATHER FIELD NYLON AND COTTON《尼龙和棉毡冬裤》.pdf

1、C 26 JUY 19s SUPERSEDING MIL-T-43497C 23 January 1984 MILITARY SPECIFICATION TROUSERS, COLD WEATHER, FIELD,NYLON AND COTTON This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope, This document covers water repellent sateen trousers wi

2、th leg .rgo pockets. 1.2 Classification, The trousers shall be one type in the following classes and sizes (see 6.2). Class 1 - Olive Green 107 Class 2 - Woodland Camuflage Schedule of sizes X-Short X-srria 11 Small Medium Short X-small Sma 11 Medium Large X- 1 arg e Regu 1 ar X-sma 11 Sma 11 Medium

3、 Large X- 1 arg e Long X-sma 11 Small Medium Large X-large Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: U.S. Army Natick Research, Development, and Engineering Center, Natick, MA 01760-5014 b

4、y using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter, AMSC N/A FSC 8415 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. THIS DOCUMENT CONTAINS y3 PAGES. Provided by IHSNot for Resa

5、leNo reproduction or networking permitted without license from IHS-,-,-MIL-T-43497D 84 99Ob 0374LbL 3 = MIL-T-4349 7D 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, stanciards, and handbooks. The following specifi- cations, standards, and handbooks form a part of this specif

6、ication to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation. SPECIFICATIONS FEDERAL A-A-2 03 V-B-87 1

7、 V-F- 106 V-L-6 1 V-T-280 DDD- L- 2 O PPP-B-636 MILITARY MIL-B-371 MIL-B-543 MIL-T-3530 MIL-F-10884 MIL-L-35078 MIL-C-43191 MIL-T-43548 MIL-T-43566 - Paper, Kra,;, Untreated - Button, Sewing Hole, and Button, Staple, (Plastic) - Fasteners, Slide, Interlocking - Laces, Nylon - Thread, Gimp, Cotton, B

8、uttonhole - Label: For Clothing, Equipage, and Tentage - Boxes, Shipping, Fiberboard (General Use) Braid, Textile, Tubular Buckles, Tongueless and Web Strap Thread and Twine; Mildew Resistant or Water Repellent Fasteners, Snap Loads, Unit: Preparation of Semiperishable Treated Subsistence Items; Clo

9、thing, Personal Equipment and Equipage; General Specification For Cloth, Wind Resistant Sateen, Cotton and Nylon Thread, Polyester Core: Cotton-, Rayon-, or Tape, Textile, Cotton, General Purpose, Natural or Polyester-Covered in Colors STANDARDS FEDERAL FED-STD-751 - Stitches, Seams, and Stitchings

10、2 e e b Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-43477D 4 W 9799906 0374362 5 MIL-T-43497D MIL I TARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes MIL-STD-129 - Marking for Shipment and Storage MIL-STD-147 -

11、Palletized Unit Loads MIL-STD-731 - Quality of Wood Members for Containers and Pallets MIL-STD-1488 - Provisions for Evaluating Quality of Trousers (Copies of specifications, standards, and handbooks required by contractors in connection with specific acquisition functions should be obtained from th

12、e contracting activity or as directed by the contracting activity.) 2.2 specif issues Other publications. The following documents form a part of this of the documents which are DoD adopted shall be those listed in the issue ication to the extent specified herein. Unless otherwise specified, the of t

13、he DODISS specified in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS shall be the issues of the nongovernment documents which are current on the date of the solicitation. AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 3951 - Standard Practice for

14、 Commercial Packaging (Copies should be obtained f.rom the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC) Chromatic Transference Scale (Copies should be obtained from the American Association of Te

15、xtile Chemists and Colorists, P.O. Box 12215, Research Triangle Park, NC 27709.) (Nongovernment standards and other publications are normally available from the organizations which prepare or which distribute the documents. These documents also may be available in or through libraries or other- info

16、rmational services. 1 2.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, the text of this Specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a spe

17、cific exemption has been obtained. 3. REQUIREMENTS 3.1 Guide sample. Samples, when furnished, are solely for guidance and Variation from this document may information to the contractor (see 6.3). appear in the sample, in which case this document shall govern. 3 Provided by IHSNot for ResaleNo reprod

18、uction or networking permitted without license from IHS-,-,-MIL-T-43977D 4 = 77706 0374363 7 MIL-T-43497D 3.2 First article. When specified in the contract or purchase order, a sample shall be subjected to first article inspection (see 4.3, 6.2 and 6.4). 3.3 Material. 3.3.1 Basic material. 3.3.1.1 C

19、lass 1. The basic material for class 1 shall be cotton and nylon, water repellent, sateen, Olive Green 107, conforming to class 2 of MIL-C-43191. 3.3.1.2 Class 2. The basic material for class 2 shall be cotton and nylon, water repellent, sateen, Woodland Camouflage, conforming to class 3 of MIL-C-43

20、191. 3.3.1.3 Cloth for pockets, linings, and facings. The cloth for tiie side and hip hanging pockets, compass pocket, left fly and right fly lining, waistband lining and cargo pocket facings shall be basic material, ground shade cloth, dyed seconds or printed seconds cloth. conformance with class 3

21、 of MIL-C-43191 for the class 2 trousers, prior to overprinting of the camouflage pattern. The ground shade cloth shall meet the applicable basic material physical, mechanical, and dimensional requirements. Dyed seconds shall be cloth which has been rejected only for defects cited in MIL-C-43191 per

22、taining to class 2 and the color and shade shall approximate OG-107 for use in the class 1 trousers. Printed seconds shall be cloth which has been rejected only for defects pertaining to color, infrared reflectance, or camouflage printed patterns cited in MIL-C-43191 for class 2 trousers. If printed

23、 seconds are used, they must be marked on the face side with stripes, 3 inches apart across the full width running in a warpwise direction for the length of the entire roll. The stripes shall be 1/8 to 1/2 inch wide and shall be applied by the cloth finisher. The color of the stripes shall approxima

24、te any one of the camouflage print colors, and shall have an AATCC Chromatic Transference Scale rating for crocking not lower than 1.5. The ground shade cloth shall be dyed in 3.3.2 Braid, textile (tubular). The braid for the leg hem drawcord shall be water repellent treated, 4/32 inch, Olive Green

25、107, conforming to type IV, class 2 of MIL-B-371. 3.3.3 Tape. The tape shall be Olive Green 107, conforming to type I, class 8 of MIL-T-43566, except that the colorfastness to crocking and accelerated aging shall not apply. The widths of tape shall be as follows: 5/8 inch - for waist adjustment stra

26、ps and 1 inch - for waistband button tabs for cargo pocket tie tapes O c e 3.3.4 Laces, nylon. The suspender loops and leg loops shall be made from nylon laces, Olive Green 106, conforming to type I, class 2 or type II, class 2 of V-L-61 except that the requirements pertaining to length and tipping

27、shall not apply. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-43497D 84 M 9999906 0394164 9 W MIL-T-43497D 3.3.5 Labels. Each of the trousers shall have a size label and a combination identification-instruction label conforming to type VI

28、of DDD-L-20. The color of the label cloth shall be Medium Green (see 6.5). requirements of DDD-L-20 shall apply. The fastness to laundering 3.3.5.1 Size label. The size label shall conform to type I, class 2 and shall contain the information for each size as shown in table I. Provided by IHSNot for

29、ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-43477D 4 m 7979706 0394165 O m MIL-T-434 97D o .rl o -rl VI m 6. .#-i ; ad al m 6. .#-I g .rl m m 4J.N o m o4 al 6. .N G .rl 4 I rie4 mm fi m -. O0 w uu M - O0 m uu m mN Co m VI a O0 Co uu M hN k4 4 “83 om 2. G O u m M

30、O u-l G .I4 al N ar( fn a . H .ti .rl C .rl *N G .rl d I VIm QI mhl Eo QI O0 h uu CG .rl .d QIN m m m m um -. O Eo mN m o 4m 01 m h C *rl Nm . u3 6.6. *rl .rl 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-43477D 84 W 777770b 0374Lbb 2 - 3.3

31、.5.2 Combination identification-instruction label. The identification label (class 1) and instruction label (class 3) shall be combined into one label, conforming to class 3 requirements. be as follows: The body of the instructions shall 1. Wear as outer garment in cold-wet climate or as the inner l

32、ayer of the cold-dry uniform. 2. Button in liner for extra warmth. Remove it when damp or wet and allow to dry. 3. Attach suspender hooks to waist loops. 4. Adjust waist by buckle straps. 5. Ventilate by loosening drawcords. 6. Wear leg bottoms outside footgear and secure drawcords. 7. Brush off sno

33、w and frost before entering heated shelter. 8. Avoid contact with heated stoves, open fires or other high heat source; fabric may fuse. 9. Dry trousers and liner separately. 10. Lubricate slide fasteners with lead pencil, graphite or wax. 11. For cleaning and restoring and water repellency, return t

34、o laundry for machine washing in accordance with established procedures for quarpel treated garments. 12. Machine washing: Use Permanent Press Cycle. Wash in warm water using mild detergent. 13. Hand washing: Wash in warm water using mild detergent. DO NOT WRING OR TWIST. Rinse in clean warm water.

35、14. DO NOT USE CHLORINE BLEACH OR STARCH. 15, Drying: Dry at low heat (do not exceed 1300F). After drying, tumble at room temperature for 10 minutes. Remove immediately from dryer. To drip dry, remove from water and place on a rustproof hanger. DO NOT REMOVE THIS LABEL 7 Provided by IHSNot for Resal

36、eNo reproduction or networking permitted without license from IHS-,-,- MIL-T-43477D 4 979770b 0374Lb7 4 3.3.6 Thread, The thread for all seaming and stitching shall be cotton-, rayon-, or polyester-covered polyester core thread, ticket nos. 30, 3 ply, 50, 2 or 3 ply and 70, 2 ply conforming to MIL-T

37、-43548, The color shall be Olive Drab S-1 C.A. 66022. The thread shall be water repellent treated in accordance with type II, class 3 of MIL-T-3530. 3.3.7 Gimp. The gimp for reinforcing buttonholes shall be cotton, Olive Drab S-1 C.A. 66022, conforming to size No. 8, type I or II of V-T-280. The dye

38、d gimp shall show fastness to laundering (after 3 cycles) to or better than the standard sample (see 6.3). When no standard sample is available, the dyed gimp shall show “good“ fastness to laundering (after 3 cycles). 3.3.8 Buttons. The buttons shall be type II, class D, style 26, 30-line, Olive Gre

39、en Shade BP, Cable No. 62016 dull finish, conforming to V-B-871. t 3.3.9 Fastener, slide, interlocking. The slide fastener shall be type I, style 3, size MS, short tab pull with thong, brass chain, conforming to V-F-106 except that the tapes shall be 9/16 2 1/32 inch wide and the finished length of

40、the thong after assembly shall be 3 + 3/4 inches. for the various sizes shall be of sufficient lengths to comply with operations 11 and 12 of table III. The slide fastener tapes shall be Olive Drab Shade S, Cable No. 66519, and shall show fastness to laundering. When no standard sample (see 6.3) is

41、available, the dyed tapes shall show “good“ fastness to laundering. The slide fasteners 3.3.10 Fasteners, snap. The snap fastener for pocket flaps shall be brass, style 2A, finish 2, male and female complete, consisting of stud with size 1 or 2 eyelet and socket with size 1 or 2 eyelet (instead of b

42、utton) conforming to MIL-F-10884. 3.3.11 Buckles. The buckles for waist adjustment straps shall be tongueless 2 bar, style 3, 5/8 inch, conforming to type II, class 3 of MIL-B-543. 3.4 Design. The trousers have hip pockets, side front pocket, leg cargo pockets with tie tapes and pocket flaps having

43、snap fastener closures, compass pocket, waist adjustment straps, suspender loops, inside button tabs and leg hem drawcords (see figure i). 3.5 Figure. Figure 1 is furnished for information purposes only. If there are any inconsistencies between the document and the figure, the document shall control

44、. 3.6 Patterns, Standard patterns, which provide an allowance of 1/2 inch for double-needle or safety-stitch joining seams, 1/4 inch for pocket flaps and 3/8 inch for other seams will be furnished by the Government to the contractor for cutting working patterns. The working patterns shall be duplica

45、tes of the Government patterns which show size, placement of pockets, and notches for proper assembly of all parts. shall not be altered in any way. The Government patterns and working patterns 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-

46、V3V77D BLf 7777706 0374368 b MIL-T-4349 7D 3.6.1 List of pattern parts. The pattern components for the trousers shall be cut from materials as specified and according to the number of parts listed in table II. TABLE II. List of pattern parts Component Nomenclature Cut parts Cotton/nylon sateen Front

47、 2 cloth Back 2 Side pocket bearer 2 Side pocket facing l/ 2 Side pocket flap lining 2 Side pocket flap 2 Cargo pocket 2 Cargo pocket flap 2 Cargo pocket facing i/ 2/ 2 Fly (one right and one left) - l/ Hip pocket bearer 2 Hip pocket cord (facing) 2 Hip pocket flap 4 Right fly lining l/ 1 Compass po

48、cket l/- 1 optional) 1 Hip pocket l/ 2 Side front Pocket - i/ 2 Compass pocket (overedge construction - 2 - i/ May be cut from printed seconds or ground shade material. - 2/ The cargo pocket facing, belt loops, and waistband lining may be roll-cut. 3.7 Construction. 3.7.1 Stitches, seams, and stitch

49、ing. Stitch, seam, and stitching types specified in table III are those covered by FED-STD-751. Whenever two or more seam or stitch types are given for the same part of the operation, any one of them may be used. When stitch type 401 is used, the looper thread shall be on the inside of the trousers. Seam allowances shall be maintained with seams sewn so that no raw edges, runoffs, twists,