ARMY MIL-T-62501-1986 TRUCK MAINTENANCE WITH VERTICAL LIFT PLATFORM GASOLINE ENGINE DRIVEN 11 000 POUNDS GVW 4X2 COMMERCIAL《11 000 磅 GVW 4X2型 汽油发动机驱动的垂直升降台》.pdf

1、MIL-T-62501 23 9997906 O203760 3 MIL-T-62501(AT) 20 March 1986 MILITARY SPECIFICATION TRUCK, MAINTENANCE: WITH VERTICAL LIFT 4x2, COMMERCIAL PLATFORM, GASOLINE ENGINE DRIVEN, 11,000 POUNDS GVW, This specification is approved for use by the US Army Tank Automotive Command, Department of the Army, and

2、 is available for use by ail Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers gasoline engine driven, four-wheel, two rear-wheel drive, 11,000 pounds gross vehicle weight (GVW) commercial trucks equipped with a maintenance body and a vertically tel

3、escoping four-section mast and fold-down platform, Vehicles procured under this specification are commercial items which shall be warranted by the manufacturer as specified in acquisition documents. 20 APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications and standards. The following s

4、pecifications and standards form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in that issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the

5、 solicitation. SPECIFICATIONS FEDERAL W-B-13 1 - Battery, Storage: Vehicular, Ignition, 2 Z-T-381 - Tires, Pneumatic, Vehicular (Highway). Lighting and Storage. Beneficial comments (recommendations, additions, deletions) and any I pertinent data which may be of use in improving this document should

6、be addressed to: US Army Tank-Automotive Command, ATTN: AMSTA-UED , Warren, MI 48397-5000, by using the self-addressed Standardization I Document Improvement Proposal (DD Form 1426) appearing at the end of I this document or by letter. I I I AMSC N/A DISTRIBUTION STATEMENT A. Approved for public rel

7、ease; distribution is unimitedo /THIS DOCbiENT CONTAINS -2fi-. PAGES. -, Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-bZCOL 23 797770b 0203761 5 W I 2 MILITARY MIL-P-514 - Plates, Identification, Instruction and Marking, Blank . MIL-B-46176

8、- Brake Fluid, Silicone, Automotive, All Weather, Operational and Preservative. MIL-H-83282 - Hydraulic Fluid, Fire-Resistant, Synthetic Hydrocarbon Base, Aircraft, NATO Code Number H-537. STANDARDS FEDEm FED-STD-297 - Rustproofing of Commercial (Nontactical) P body; vertical platform assembly in st

9、owed position; a full complement of fuel, lubricants and coolant. 3.2.5 Gross vehicle weight. The gross vehicle weight (GVW) shall consist of curb weight, operator (weight computed at 175 pounds) and a payload distributed throughout the length of the vehicle body, to provide not: less than the speci

10、fied GVW. The GVW shall be not less than 11,000 pounds. 3.2.6 Weight distribution. The distribution of the GVW for the purpose of establishing suspension, axle and tire capacities shall be determined with the payload uniformly distributed over the load area. 3.2.7 Ratings. Vehicle and component rati

11、ngs shall be the manufacturers published ratings. Component and vehicular ratings shall not be raised to meet the requirements of this specification. When published ratings are not available, verification of the ratings must be submitted to the engineering office of the procuring activity. The ratin

12、gs shall be established by the manufacturer of the equipment being verified . 3.2.8 Cab-to-axle. The cab-to-axle dimension shall be not less than 60 inches. The cab-to-axle dimension shall be measured from the back of. the cab to the center of the rear axle. 3.2.9 Safety standards. The vehicle shall

13、 comply with the requirements of OSHA 1926.556, and with ANSI A92.2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-b2501 23 7999906 O203767 b = MIL-T-62501 (AT) 3.2.10 Accessibility. The design of the vehicle and optional equipment shall perm

14、it access for routine servicing, and shall permit access for replacement and adjustment of component parts and accessories with minimal disturbance of other components and systems. 3.3 Performance. 3.3.1 Speeds and gradeability. The vehicle shall maintain a high speed of not less than 58 miles per h

15、our (mph) on smooth, approximately level, hard surfaced roads. grades of at least 20 percent in low-speed range. gradeability requirements shall be met with the vehicle loaded to specified GW?. The vehicle shall be capable of ascending Speed and 3.3.2 Service brakes. The service brakes shall control

16、 and hold the vehicle, when loaded to its specified GVW, on a 30 percent grade. The service brakes shall stop the vehicle within the stopping distance requirements of Federal Motor Carrier Safety Regulation 393.52, under all conditions of loading, up to specified GW. 3.3.3 Parking brakes* A hand- or

17、 foot-actuated parking brake shall be furnished in addition to the service brakes. When a foot actuated parking brake is furnished, a hand lever shall be furnished to release the parking brake. of holding the vehicle loaded to specified GVW on a 30 percent slope. The vehicle parking brake shall be c

18、apable 3.3*4 Upsetting stability. With one and one-half times the specified load (see 3.6.2) placed on the work platform with the vehicle otherwise unloaded, and with the two outriggers extended, the telescopid mast shall be capable of placing and holding the loaded platform in any attainable positi

19、on of the equipment without causing the vehicle to become unstable. The vehicle shall be deemed unstable with one and one-half times the specified load when any one of the vehicle wheels or outriggers lifts off of the ground. The stability test shall not cause any permanent deformation beyond the el

20、astic limit of any component of the vehicle. The vehicle shall also be deemed unstable if, with twice the specified load (see 3.6.2), the inner tire of either rear wheel lifts o?f o? the ground. 3.3.4.1 Stability on slopes. With one and one-third times the specified load (see 3.6.2) and the vehicle

21、otherwise unloaded and with the vehicle not being leveled, on a 5-degree slope, facing upward and then downward, and then at right angles to the 5-degree slope, and with the outriggers extended, the telescopic mast shall be capable of placing and holding the loaded platform in any attainable positio

22、n of the equipment without causing the vehicle to become unstable. The vehicle shall be deemed unstable with one and one-third times the specified load when any one of the vehicles tires or outriggers lifts off of the ground . 8 Provided by IHSNot for ResaleNo reproduction or networking permitted wi

23、thout license from IHS-,-,-MIL-T-62501 23 m 9999906 02037b8 m 3.3.5 Wind resistance. With the specified load (see 3.6.2) in the platform and the vehicle otherwise unloaded and in elevated position, the vehicle shall be capable of withstanding a wind load of 7 pounds per square foot without upsetting

24、, overturning, or permanent deformation of any component. calculated at the body, with the mast and platform in the most critical position that would induce tipping. greater than the wind load when the load is applied on the surface of the body, mast and platform. The maximum area exposure for wind

25、load shall be The resisting moment shall be 3.3.6 Height. The boom shall be capable of raising the work platform with rated load (see 3.6.2), measured from ground level to the platform floor, to a height of not less than 29 feet. 3.3.7 Position stability (work platform). When the vehicle is on a 5 p

26、ercent grade, without being leveled, the elevating mechanism shall hold the loaded work platform (see 3.6.2) in position within 2 inches per hour vertical. settling. hydraulic fluid stabilized at ambient air temperature. The settling shall be measured with 3.4 Chassis components. 3,4.1 Engine. The e

27、ngine shall be a liquid cooled, internal combustion, four-stroke cycle, gasoline type, with not less than six cylinders. horsepower at manufacturers recommended governed speed and shall have a net torque capacity of not less than 215 pound feet. Engine net torque and net horsepower rating shall be d

28、etermined in accordance with SAE 5245 or SAE 51349. The engine shall develop the specified torque and horsepower when operated on unleaded fuel with a research octane rating of 91. fuel when used in accordance with the operators manual. shall be provided. The fan clutch shall reduce the fan speed au

29、tomatically when the fan is not required for engine cooling. The engine shall develop not less than 115 net brake The engine shall be capable of warranted operation on unleaded A fan clutch 3.4.1.1 Power plant heaters. When specified (see 6.2), coolant and battery heaters shall be provided. Heaters

30、shall operate on 120 volts alternating current (ac), and shall be wired through a junction block to a single three-pronged (male), weatherproof, slave receptacle for receiving external power and for grounding the vehicle. A three-wire connecting cable, 25 feet long and of adequate line capacity to s

31、upply power for heater units simultaneously, shall be furnished. The connecting cable shall include a matching female connector at the vehicle end and a standard, three-pronged (two power plus one ground) male connector at the other end. Electrical apparatus shall conform to 9 Provided by IHSNot for

32、 ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-b250l1 23 W 373790b 02037b7 T Federal Motor Carcier Safety Regulation 393.77()(7). insulation of connecting cable shall withstand norma2 operating stresses in low ambient air temperature (down to minus 60F) without cra

33、cking or loss of dielectric capacity. All heater lead wires shall be installed without interlering with vehicle component operation and without loose excess wire. A carrier for the connecting cable shall be mounted within the cab or engine compartment and shall provide positive cable retention durin

34、g vehicle operation. Heaters shall be furnished as follows: Electrical (a) Coolant heater, 1500-watt minimum rating, shall be installed in the engine block or lower coolant inlet hose. thermostat with an operating range of 170F to 195F shall be installed Battery heater shall have a capacity adequate

35、 to maintain the battery electrolyte at a temperature of not less than 10F during vehicle exposure in ambient air temperatures as low as minus 60F, and shall embody a themostat to limit the temperatures of the electrolyte to not more than 80F. Engine (b) 3,402 Electrical system. The electrical syste

36、m shall be in accordance with Federal Motor Carrier Safety Regulations 393.27 through 393.31 and 393.33. 3.4.2.1 Ignition system. An ignition system of 12-volt direct current (dc) potential shall be furnished. Unless otherwise specified (see 6.2), an alternator of not less than 35 amperes dc rated c

37、apacity which provides not less than 7 amperes dc output at normal engine idle speed shall be furnished, 34.242 Battery. The battery shall be of 12-volt potential. The reserve capacity rating, measured in accordance with SAE J537, shall be not less than 80 minutes. The cold cranking rating at OF, me

38、asured in accordance with SAE J537, shall be not less than 350 amperes. The battery shall be of the maintenance-free type having the maintenance-free characteristics listed in W-B-131. 3.4.2.3 Lighting. All vehicle lights and reflectors shall be as specified herein and shall conform to Federal Motor

39、 Carrier Safety Regulations 393.12, 393r19, 393.20 and 393.22 through 393.26(d). 3.4.2.3.1 Turn signals. Turn signals shall be furnished. Turn signal lights may be combined with stoplights at rear and with parking lights at front. Taillights and stoplights may be incorporated into the same housing.

40、Control for turn signals shall be self-cancelling type, with visible and audible type flash indicator. Turn signal lamps shall conform to SAI3 J588 and turn signal operating unit shall conform to SAE 5589, class A. 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without licen

41、se from IHS-,-,-MIL-T-62501 23 = 7777906 0203770 b MIL-T-62501(AT) 3.4.2.4 Radio interference suppression. The vehicle shall be Any body equipment emitting radiation shall be suppressed to the suppressed to limit electromagnetic radiation in accordance with CAE 5551. same level as the vehicle chassi

42、s. 3.4.3 Fuel system. The fuel system shall conform to Federal Motor Carrier Safety Regulations 393.65 and 393.67 (except compliance with 393.67(c), subparagraphs (i), (4)(ii), (ll), 393.67(d) and 393.67(f) is not required). The capacity of the fuel tank shall be not less than 19 gallons. 3.4.3.1 Ai

43、r cleaner. An air cleaner shall be furnished. men equipped with an oil bath type air cleaner, oil capacity shall be not less than 1 pint. 3.4.4 Exhaust system. The exhaust system shall conform to Federal Motor Carrier Safety Regulation 393.83. A spark arrester with an efficiency rating of not less t

44、han 80 percent when tested in accordance with SAE 5350 shall be furnished, except on turbocharged engines. 3.4.4.1 Exhaust system safety shield. The exhaust system or hydraulic system shall be shielded so that, in the event of a hydraulic line rupture or hydraulic fluid leak, the hydraulic fluid wil

45、l not come into contact with any part of the vehicle exhaust system. 3.4.5 Gear train. 3.4.5.1 Transmission. Unless otherwise specified (see 3.4.5.3), a manually shifted transmission shall be provided. The transmission shall have not less than four forward speeds and one reverse speed. torque capaci

46、ty of the transmission shall be at least equal to the maximum torque delivered by the engine. The transmission shall be provided with a power takeoff opening conforming to SAFI 5704. The transmission shall provide for maximum ease of shifting in all speeds. Input 3.4.5.2 Clutch. The clutch shall be

47、the largest capacity clutch offered for the vehicle and engine furnished, with clutch torque capacity exceeding maximum delivered engine torque. 3.4.5.3 Automatic or semiautomatic transmission. When specified (see 6.2), the vehicle shall be provided with an automatic or semiautomatic transmission. T

48、he transmission shall provide continuous drive. The transmission shall include a hydraulic torque converter and not less than four forward gear ratios. Normal driving range selector position shall provide not less than four gear ratios without movement of the selector. The transmission shall be prov

49、ided with SAE 5704 power takeoff openings. Input torque capacity of the transmission shall be at least equal to the maximum torque delivered by the engine. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MEL-T-hi501 23 Oh 0203771 8 9 MIL-T-62501 (AT) 3.4.5.4 Power takeoff. The power takeoff shall be of a rated Controls to operate the power A caution plate or decai reading “DO NOT OPERATE VEHICLE