ARMY MIL-V-44323 A-1988 VEST TACTICAL LOAD BEARING《战术携带载具背心》.pdf

1、MIL-V-44323A 27 April 1988 SUPERSEDING 26 January 1988 MIL-V-“+4323(GL) MILITARY SPECIFICATION VEST, TACTICAL LOAD BEARING This specification is approved for use by all Departments and Agencies of the . ,S- Department of Defense. W$. l. SCOPE 1.1 Scope. This document covers a web harness load bearin

2、g vest to carry ammunition, grenades, canteen, and other equipment. The vest comes in one type and size only (see 6.1). 2. APPLICABLE DOCUMENTS 2-1 Government documents. * 2.1.1 Specifications, standards, and handbooks. The following specifi- cations, standards, and handbooks form a part of this spe

3、cification to the documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation. extent specified herein. Unless otherwise specified, the issues of these SPECIFICATIONS FEDERAL A-A-50083 - Ba

4、g, Plastic, Folded Garment (General Use) DDD-L-20 - Label: For Clothing, Equipage and Tentage, PPP-B-26 - Bag, Plastic, (General Purpose) PPP-B-636 - Boxes, Shipping, Fiberboard Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this d

5、ocument should be addressed to: U.S. Army Natick Research, Development, and Engineering Center, Natick, MA 01760-5014 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. 0 AMSC N/A FSC 8415 DISTRIBUTION STATEMEN

6、T A. Approved for RubLig_r_f3_lease7; distribution is unlimited. Clothing, Personal Equipment and Equipage; General Specification For STANDARDS FEDERAL FED-STD-751 - Stitches, Seams, and Stitchings MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by MIL-STD-129 - Marking for Ship

7、ment and Storage MIL-STD-147 - Palletized Unit Loads MIL-STD-731 - Quality of Wood Members for Containers and Pallets Attributes * (Copies of specifications, standards, and handbooks required by contractors in connection with specific acquisition functions should be obtained from the contracting act

8、ivity or as directed by the contracting activity.) * 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this specification to the extent specified herein. Unless otherwise specified, the 0 issues shall be

9、those in effect on the date of the solicitation. DRAWINGS U. S. ARMY NATICK RESEARCH, DEVELOPMENT, AND ENGINEERING CENTER 2-1-1981 - Vest, Tactical Load Bearing, Assembly 2-1-1989 - Buckle Assembly, Male End 2-1-1990 - Buckle Assembly, Female End 2-1-1992 - D-Ring Assembly 2-1-1997 - Vest, Back, Pat

10、tern (Copies of drawings, publications, and other Government documents required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 2.2 Other publications. The following documents form a part o

11、f this specification to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those listed in specified, the issues of documents not listed in the DODISS shall be the issues of the nongovernment documents which are current on the date of

12、the solicitation. . the issue of theDODISS specified in the solicitation. Unless otherwise 2 Licensed by Information Handling ServicesMIL-V-44323A 84 m 7779706 0403160 4 m MIL-V-40323A AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 3951 - Standard Practice for Commercial Packaging (Copies shoul

13、d be obtained from the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) (Nongovernment standards and other publications are normally available from the organizations which prepare or which distribute the documents. These documents also may be available in or thr

14、ough libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws a

15、nd regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Guide samples. Samples of the end item, when furnished, are solely for guidance and information to the contractor (see 6.3). Variations from this document may appear in the sample, in which case this document shall gov

16、ern. 3.2 First article. When specified in the contract or purchase order, a sample shall be subjected to first article inspection (see 4.3, 6.2, 6.4). 3.3 Materials and components. Materials and components shall be as specified on Drawing 2-1-1981, and all subsidiary drawings and parts lists pertain

17、ing thereto, For materials or components for which it is stated “or equalt1, if the contractor proposes to use an item considered to be equal to the material or component specified, prior to its use the contractor shall furnish a sample of the material or component, with supporting data to the contr

18、acting officer for subsequent evaluation by the responsible military agency. Recycled materials may be used (see 6.5). 3.4 Construction. The construction shall conform in all respects to the drawings in 2.1.2 and all subsidiary drawings and as specified herein. 3.4.1 Stitches, seams, and stitching.

19、All stitches, seams, and stitchings, except bartacking, shall be performed using stitch type 301 with 7 to 9 stitches per inch and shall conform to FED-STD-751, 3.4.1.1 Type 301 stitching. Ends of all stitching, except box and box-x, shall be backstitched or overstitched 1 inch minimum except where

20、ends are turned under in a hem or held down by other stitching. On box and box-x stitching, all ends shall be backstitched or overstitched 1/2 inch minimum. Thread tension shall be maintained so that there will be no loose stitching resulting in loose bobbin or top thread, or excessively tight stitc

21、hing resulting in puckering of the materials sewn. The lock shall be imbedded in the materials sewn. 3 Licensed by Information Handling Services“ “- . .- MIL-V-44323A 84 W 9797706 O403161 h m MIL-V-44323A 3.4.1.1.1 Repairs of type 301 stitching. Repairs of type 301 stitching shall be as follows: a.

22、When thread breaks or bobbin run-outs occur during stitching, the stitching shall be repaired by restarting the stitching a minimum of 1 inch (1/2 inch for box and box-x stitching) back of the end of the stitching. b. Thread breaks or two or more consecutive skipped or run-off stitches noted during

23、inspection of the item (in-process or end item) shall be repaired by overstitching. The stitching shall start a minimum of 1 inch in back of the defective area (1/2 inch for box and box-x stitching), continue over the defective area, and continue a minimum of 1 inch (1/2 inch for box and box-x stitc

24、hing) beyond the defective area onto the existing stitching. Loose or excessively tight stitching shall be repaired by removing the defective stitching without damaging the materials, and restitching in the required manner. I/ - 1/ When making the above repairs, the ends of the stitching are not req

25、uired to - be backstitched. 3.4.1.2 Automatic stitching. Automatic stitching machines may be used to perform any of the stitch patterns provided that the requirements for the stitch pattern, stitches per inch, and size and type of thread are met, and that at least three tying, overlapping, or back s

26、titches are used to secure the ends of the stitching. 3.4.1.3 Bartacking. stitching. Bartacking Length 1 + 1/16 inch 3/T + 1/16 inch . Bartacking shall be free from thread breaks and loose shall be as follows: Width No. of stitches 1/8 + 1/32 inch 1/8 - T 1 /32 inch 42 42 3.4.1.4 Thread ends. All th

27、read ends shall be trimmed to a maximum length of 1/4 inch. 3.4.1.5 Lubrication of thread. Lubrication shall be permitted only to the extent that it does not stain the adjacent fabric. Only non-wicking lubricants shall be used. 3.4.2 Fusing of ends of nylon webbing, cord, and material. Ends of webbi

28、ng, including bias cuts, cord and raw edges of nylon material shall be fused smooth. Fusing of webbing ends and nylon material shall be accomplished prior to assmbling for stitching. The apparatus used to fuse the webbing and cord ends, and material shall be capable of providing sufficient heat to p

29、rovide a smooth edge with the cut ends of the yarns fused together to prevent separation. 3.4.3 Location marks. Location marks shall not be drilled. Printed markings shall not be more than 1/32 inch in width. 4 Licensed by Information Handling Services3.4.4 Repairs. Except as otherwise specified her

30、ein, repairs shall not be made to the vest. 3.4.5 Replacement of defective components. During the spreading, cutting and manufacturing process, components having material defects or damages that are classified as defects in 4.4.3 shall be removed from production and replaced with non-defective and p

31、roperly matched components * 3.4.6 Setting of eyelets. Holes shall be prepunched or drilled to receive the eyelets. Holes prepunched to receive the eyelets shall be smaller than the outside diameter of the eyelet barrel so that the barrel must be forced through the hole. 5 3.4.6.1 Eyelets, with wash

32、er, brass. The brass eyelets with washer shall be securely clinched in a manner that will prevent detachment from or cutting of . the surrounding material. The eyelets shall be clinched without splitting. 3.4.6.2 Eyelets, aluminum. The aluminum eyelets shall be installed using score setting dies con

33、forming to J. C. Rhodes part number 1-KW-1KL and lOlY-Klom, or Stimpson Co. Part Number A 2744-7 or equal (see 6.6). The eyelet shall be securely set in a manner that will prevent detachment from, or cutting of, the adjacent material. The clinched portion- of the eyelet shall be on the inside of the

34、 assembly. * 3-4.7 Setting of grommets. Holes shall be prepunched or drilled to receive the grommets. Holes prepunched to receive the grommets shall be smaller than through the hole. The grommet shall be securely clinched without cutting the adjacent material. 0 the outside diameter of the grommet b

35、arrel so that the barrel must be forced 1 * 3.4.8 Setting of snap fasteners. A hole shall be prepunched or drilled to receive the button and eyelet components of the snap fasteners. The hole shal be smaller than the outside diameter of the button and eyelet barrels so that the barrel must be forced

36、through the hole. The hole shall not be punched in the setting operation with the button or eyelet barrel. The fasteners shall be securely clinched without cutting the adjacent materials and no more than three splits shall occur in the button or eyelet barrels. 3.5 Marking. The identification markin

37、g shall be applied in the location shown on Drawing 2-1-1997 and shall conform to type IV, class 5 of DDD-L-20. The letters ltUSfl shall be applied in the size characters and in the location indicated on Drawing 2-1-1981 and shall conform to type IV, class 9 of DDD-L-20. Fastness of class 9 marking

38、shall be as specified for class 5 marking. 3.6 Patterns. Standard patterns for textile components other than tape or webbing are shown full scale on drawings and provide allowances for all seams and shall be used for making working patterns. The standard patterns shall not be altered in any way. 5 L

39、icensed by Information Handling ServicesMIL-V-44323A 84 m 9777706 0403163 T m 3.7 Workmanship. The finished vest shall be clean. The textile components shall be free of defects, such as holes, tears, loose weaving, or unfused ends. The hardware shall be free of corroded areas, sharp edges, or unfini

40、shed areas. 4, QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase

41、 order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in this specificatin where such 44 inspecti

42、ons are deemed necessary to assure supplies and services conform to prescribed requirements. . 4.1.1 Responsibility for compliance. All items must meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection syste

43、m or quality program, The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of assuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling in quality conforma

44、nce does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to acceptance of defective material. 4.1.2 Responsibility for dimensional requirements. Unless otherwise speci- fied in the contract or purchase order, the contractor is respo

45、nsible for assuring that all specified dimensions-have been met. When dimensions cannot be examined on the end item, inspection shall be made at any point, or at all points in the manufacturing process necessary to assure compliance with all dimensional requirements. 4.1.3 Certificate of compliance.

46、 When certificates of compliance are sub- mitted, the Government reserves the right to check test such items to determine the validity of the certification. 4.2 Classification of inspection, The inspection requirements specified herein are classified as follows: a. First article inspection (see 4.3)

47、. b. Quality conformance inspection (see 4.4). 4.3 First article inspection. When a first article is required (see 6.2), it shall be examined for the defects specified in 4.4.3, 4.4.4 and 4.4.5. The presence of any defect shall be cause for rejection of the first article. 4.4 Quality conformance ins

48、pection. Unless otherwise specified, sampling for inspection shall be performed in accordance with MIL-STD-105. 6 Licensed by Information Handling ServicesMIL-V-YY323A A4 E 7979906 0403164 L m MIL-V-44323A 4.4.1 Component and material inspection, In accordance with 4.1, components and materials shal

49、l be inspected in accordance with all the requirements of referenced documents unless otherwise excluded amended, modified, or qualified in this document or applicable purchase document. 4.4.1.1 Certification. The contractor shall furnish a certificate of compliance for the buckle specified on Drawings 2-1-1989 and 2-1-1990, for the D-rings specified on Drawing 2-1-1992, the cord-lock specified on Drawing 2-1-1981 (see 6.7). 4.4.2 In-process inspection. Inspection shall be made at any point or during any phase of the manufacturing operation to determine whether cut lengths, cut par