ARMY MIL-W-14969-1968 WARHEAD 2 75 INCH ROCKET XM229 (TWO-PIECE) PARTS FOR《XM229型2 75英寸弹头(上下两件)零件》.pdf

1、PURCHASE DESCRIPTION. - WARHEAD, 2.75 INCH ROCKET XM229, (TWO PIECE) PARTS FOR 1. SCOPE 1.1 This specification covers the quality assurance provisions and special requirements not covered by the drawings, for one type of warhead designated as Warhead, 2.75 Inch Rocket, XM229, (Two Piece). 2. APPLICA

2、BLE DRAWINGS 2.1 The following documents of the issue in effect on date of invitation for bids, or request for proposals, form a part of this specification to the extent specified herein. SPECIFICATIONS FEDERAL TT-C-490 - Cleaning Methods and Pretreatment of Ferrous Surfaces for Organic Coating MILI

3、 TA RY MIL-A-2550 - Ammunition and Special Weapons, 1-1-45607 - Inspection Equipment, Supply and MIL-STD-105 - Sampling procedures and tables for General Specification for Maintenance of inspection by attributes STAMDARDS FEDERAL FED-STD-151 - Metals, Test Methods FSC: i340 Provided by IHSNot for Re

4、saleNo reproduction or networking permitted without license from IHS-,-,-NIL-STD-109 - Quality Assurance Terms and Definitions MIL-STD-1168 - Lot Numbering of Ammunition MIL-STO-1235 - Single and Yultilevel Continuous Sampling Procedures and Tables for Inspection by Attributes DRAWINGS ORDNANCE CORP

5、S 9238883 - Warheac?, 2.75 Inch Rocket, XE229 Metal Parts Assembly (Two Piece) PURLICATIONS ORDNANCE CORPS ET-9238883 - Equinment Tabulation (Copies of speciflcatlons, standards, drawings and publications reauired by suopliers in connection with specific procurement functions should. be obtained fro

6、m the procuring activity or as directed by the contracting officer. ) of this specification to the extent specfied herein. Unless otherwise indicated, the issue in effect on date of invitation for bids or request for proiiosal shall ariply. 2.2 Other publications. - The following documents form a pa

7、rt - ,.Gage Outside diameter forward e 102, Minor diameter of fuze thread, max . Gage 103. Pitch diameter of rear thread.Gage 104. Major diameter of rear thread, min(, .Gage 105. Thread damaged or not full.,Visual 106. Foreign matter in cavity., Visual Code No. 04001 04002 04003 04004 04005 04006 Mi

8、nor : AQL 2.50 percent 201. Protective coating inadequate or 202. Paint in cavity inadequate. ,Visual 04008 204. Paint adhesion Tape Test 04010 205. Marking missing, incorrect, or illegible. Visual 04011 damaged,. Visual 04007 203. Paint not dry . Tactile 04009 4.3.3 Testing 4.3.3.1 Microexamination

9、. - Major Defect - Code No. 01002 (see Dwg. 3238882). For ductile iron, a test lug shall be cast representing the last metal poured from each ladle treated with the nodularizing agent. The test casting and microexamination shall be in accordance with ASTV-A-445. Failure of the test lue; to conform t

10、o the microstructure requirements of AST?-A-445 shall be cause for rejection of the castings from the ladle represented by the test lug. 4.3.3.2 Hardness Test 4.3.3.2.1 Ductile Iron Nose Casting Hardness Test - Major Defect - Code No, 01003. - To insure compliance with the mechanical properties requ

11、irements, each nose casting from a samnle shall be subjected to i! hardness test with a. Brinell IIard.ness Tester. The sample, 10 per cent rninimua, renresentntive of extrem furnace environment, shall be selected. ffon each heat treat batch when i! batch tyne nimace is used for f!nal heat treatment

12、. When a con- tinuous type furnace is used for final heat treatment, from which a 10% min. sample will also be sUlected, a heat treat batch will be coilsidered a quantity of castings not to exceed 4 hours production. The castings wkicii constitute the cancle stiall be collected at reg- ular contiiiu

13、ous fntarvals througiiout tht? 4 hour cycle, The heat treat batch thus constituted shall forn the basis for selecting castings for the tension test hereinafter prescribed. The test shall be performed as specified in 4.4.2 using equipment in accord- ance with 4.3.4. 8 Provided by IHSNot for ResaleNo

14、reproduction or networking permitted without license from IHS-,-,-fl-w-Lqqb=J 13 a i0b Oqbq831 0 - - I MIL-14-14369 (FU) 4.3.3.2.2 Valleable Iron Base Casting Hardness Test - Flajor Defect - Code No. 02007. - To insure compliance with the mechanical properties requirements, each base casting from a

15、sample shall be subjected to a hardness test with a rinell Hardness Tester. The sample, a 10% minimum, representative of extreme furnace environment, shall be selected from each heat treat batch of 1000 or fraction thereof when a batch type furnace is used for the final heat treat- ment. When a cont

16、inuous type furnace is used for final heat treat- ment, from which a 10% min. sample will also be selected, a heat treat batch will be considered a quantity of castings not to exceed 4 hours production. The castings which constitute the sample shall be collected at regular continuous intervals throu

17、ghout the 4 hour cycle. The heat treat batch thus constituted shall form the basis for selecting sample castings for the tension test here-in-after pre- scribed. The hardness test shall be performed on the approximate center of the bottoni of the castings. as specified in 4.4.1 using equipment in ac

18、cordance with 4.3.4, The test shall be performed 4.3.3.3 Tension Test 4.3.3.3.1 Tension Test on Nose (Ductile Iron) - Major Defect - Code No. 01004. - The hardest and softest casting representing the days heat treat production as determined in 4.3.3.2.1 shall be subjected to the test specified in 4.

19、4.3 using ecpipment in accord- ance with 4.3.4. Failure of any test specimen to comply with the applicable physical properties requirements shall be cause for rejection of the days heat treat production represented by the specimens. When malleable iron is used two base castings from each heat treat

20、batch; one of the hardest and one of the softest as determined by 4.3.3.2.2 shall be subjected to the tension test in accordance with 4.4.4, to determine compliance with the mechanical properties re- quirements of the applicable drawing. When steel bases are used, two bases from each heat treatment

21、or stress relieved batch of 5000 or fraction thereof shall be subjected to the tension test. Failure of any specimen to comply shall be cause for rejection of the batch represented by the specimen. The test shall be performed as speci- fied in 4.4.4 using; equipment in accordance with 4.3.4. 4.3.3.4

22、 Hydrostatic Test. - Critical defect - Code No. 03031 - Each metal parts assembly shall be subjected to the required constant internal hydrostatic pressure to determine compliance with re- quirements s?ecifieO on dwg. 9238883. Failure of any assembly to comply shall be cause for rejection of the ass

23、embly. Metal parts assemblies which comply shall be stamped with the letter “H“ as indicated on the assembly drawing, The test shall be performed as specified in 4.4.5 using equipment in accordance with 4.3.4. 4.3.3.3.2 Tension Test on Base. Major Defect - Code No. 02008. 9 Provided by IHSNot for Re

24、saleNo reproduction or networking permitted without license from IHS-,-,-MIL-W-L47b7 13 m 799770b 04b4832 2 m -c r M I L- W- 1 4 9 6 9 ( MU 1 4.3.3.5 Air pressure - Critical defect - Code No, 03032. - Each shell assembly that has passed the hydrostatic pressure test, as indicated by the letter “H“ s

25、tamped on the body, shall, after completion of the drying cycle be subjected to a submerged air pressure test. Any shell assembly failing to comply with requirements specified on Dwg. 9238883 as evidenced by air bubbles rising to surface of water shall be rejected. Air bubbles caused by entrapped ai

26、r on the outside of the shell shall not be cause for rejection of the shell assembly. Shell assemblies which comply with the requirements of Dwg. 9238883 shall be stamped with the letter “A“ as indicated on the assembly drawing. The test shall be performed as specified in 4.4.6 using equipment in ac

27、cordance with 4.3.4. 4.3.3.6 Salt Spray Test - Major defect (see 3.5) Code No. 04012. - The sample size for this test shall be as follows: During production, one warhead from each days production, shall be subjected to the salt spray test as specified in 4.4.8, until five consecutive days production

28、 have successfully passed the test. Sampling shall then be reduced to one sample twice per week, upon reduced sampling if one failure occurs, corrective action shall be taken and sampling shall revert to one specimen from each days production until five consecutive days production have again success

29、fully passed the test. If two consecutive failures occur after the contractor has been notified to take corrective action in either the original sampling plan or the reduced sampling plan, inspection for acceptance shall be stopped until necessary corrective action has been taken. Any specimen (warh

30、ead) which does not comply with any of the following test criteria shall be considered a failure. The specimen, when subjected to the salt spray test as specified in 4.4.8, shall show no more than i/8 inch creepage, blistering, or loss of adhesion of the paint as measured from the scribe mark. At al

31、l other points there shall be no more than a trace of film failure such as blistering, or corrosion, and not more than twenty scattered blisters, none larger than 3/16 inch in diameter on the painted sur- face of the warhead. This is intended that the maximum amount of corrosion in the salt spray te

32、st be comparable to photograph 8-1 in ASTM Standard Method of Evaluation Degree of Resistance to Rust- ing obtained with paint or iron and steel surfaces, D610-43. This test shall be performed as specified in 4.4.8 using equipment in accordance with 4.3.4. 4.3.3.7 Drop Test - Major Defect - Code No.

33、 04013 - Beginning with the first lot and continuing until five consecutive lots have been tested a sample from each lot shall be.subjected to a drop test as specified in 4,4.7 using equipment in accordance with 4.3.4. Upon satisfactory results from five consecutive lots the contractor may reduce te

34、sting to a sample from one randomly selected lot per month. The contractor shall return to the five lot requirement upon failure of any lot. The sample shall consist of 23 randomly selected painted assemblies which have passed all other requirements of this specification. The lot represented by the

35、sample shall be rejected if two (2) op more warheads fail to 10 .- I . . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-W-L4967 L3 = 777770b 0464833 4 = - - - 1-1496g (MU) comply with the inspection criteria. If only one (1) warhead fails, a ret

36、est is permissible as follows: For retest, a new sample, consisting of 46 warheads randomly selected from the lot shall be subjected to the drop test in accordance with 4.4.7. If one or more warheads fail to comply with the inspection criteria, the lot shall be rejected. Inspection Criteria - The wa

37、rheads shall be subjected to and comply with a Hydrostatic and Air test in accord- ance with 4.3.3.4 and 4.3.3.5. There shall be no visual evidence of cracklike discontinuities on the surface of the warheads after the Hydrostatic and Air tests. This is considered to be a destructive test. 4.3.4 Insp

38、ection Equipment, - Equipment Tabulation Number ET-9238883 identifies the inspection equipment required to perform the examinations and tests prescribed in this section. The contractor shall desipn inspection equipment in accordance with the instructions in paragraph 6.3. equipment drawings and list

39、s provided and revised in accordance with the requirements of the ET may be used by DOD activities for design, procurement, manufacture, testing, evaluation, pro- duction and receiving inspection, overhaul, shipping, storage, identification of stock, ordering and storage of replacement parts, inspec

40、tion of items at overhaul, general maintenance of equipment, construction, survey and whenever inspection equipment drawings are needed. 4.3.4.1 Government rights to documentation. - Inspection 4.3.4.2. Supply and Maintenance. - Supply and maintenance of the equipment listed on the ET shall be in ac

41、cordance with Specification MIL-1-45607. 4.4 Test Methods and Procedures 4.4.1 Hardness Test on Base. - After final heat treatment, the hardness test shall be performed on the base. Procedures for this test are as prescribed by Federal Test Method Standard No. 151 Method 242.1. 4.4.2 Hardness Test o

42、n Nose, Elongated, - After final heat treatment, the hardness test shall be performed on the nose, elongated, between the bourrelets. Procedures for this test are as prescribed by Federal Test Method Standard Mo. 151. Method 242.1. 4.4.3 Tension Test on Nose, Elongated. - Two tension test speamens c

43、onformine; to a standard “R“ type specimen as prescribed by Federal Test Method Standard No. l5i shall be taken longitudinally from each sample. Samples shall be taken 1800 apart between bourrelets. The criteria for determining yield strength and elongation shall be as prescribed by Federal Test Met

44、hod Standard No. 151 Method 211.1. . 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-W-147b7 13 77777Ob 04b4834 b = -e MIL-W-14969 (MU) 4.4.4 Tension Test on Base. - From the samples provided in accordance with 4.3.3.3.2 one tensile test speci

45、men conforming to a standard “R“ type specimen as presc,ribed by Federal Test Method Standard No. l5i shall be taken from the bottom of each base. The criteria for determining yield strength and elongation shall be as prescribed by Federal Test Method Standard No. 151, Nethod 211.1. 4.4.5 Hydrostati

46、c Test - (see 4,3.3.4). - The metal parts assembly shall be hydrostatically tested using equipment capable of performing the test accurately and consistently. In perfor- ming the test, the pressure will be applied gradually until the required minimum pressure is reached, after which the pressure wil

47、l be held for a minimum of 5 seconds. The equipment shall be calibrated prior to the start of each days operation, at intervals of not over 2 hours of continuous operation, and prior to re- starting the operation after a layoff of 1 hour or more. that have passed the hydrostatic test shall be mounte

48、d in an approved fixture in such a manner that the body assembly will be completely submerged in water. The air pressure shall be applied and held for a minimum of -15 seconds. 4.4.7 Drop Test. - Warheads from a sample as provided in accordance with 4.3.3.7 shall be dropped from a height of 5 feet o

49、nto a steel plate having a minimum thickness of 3 inches and a brine11 hardness of at least 207, The steel plate shall be solidly supported in a horizontal plane over its entire bearing area by a minimum thickness of 24 inches of concrete. The steel plate shall have a smooth flat surface and shall have a length and width of at least 36 inches. The plate shall be surrounded on all four sides by a heavy steel enclosure of su