ASTM A1105-2017 Standard Specification for Corrugated Steel Manhole Assemblies《波纹钢人孔组件的标准规格》.pdf

1、Designation: A1105 17Standard Specification forCorrugated Steel Manhole Assemblies1This standard is issued under the fixed designation A1105; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in pa

2、rentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the manufacture and purchaserequirements of products used for assembly and construction ofcircular reinforced corrugated

3、steel manholes used in sewerand water works. Products covered by this specification are notnormally used for the conveyance of sanitary or industrialwastes. The steel sheet used in fabrication of the manholestructures has a protective metallic coating of zinc(galvanizing), aluminum, 55 % aluminum-zi

4、nc alloy, or zinc-5 % aluminum-mischmetal alloy, or a polymer pre-coating.1.2 Part I, Sections 1 through 11, of this specificationpresents general requirements and requirements that are com-mon to each corrugated steel product in the sections outlined in1.3.1.3 Part II of this specification presents

5、 specific require-ments for each manhole product in the following section:Product SectionGrade Rings 12Manhole Structures 13Base Section 14Steps and Ladders 151.4 Steel sheet with zinc, aluminized or polymeric coatingmay be specified for the fabrication of the manhole structures.Manhole structures m

6、ade from sheets with composite coatingsare always furnished with an approved coating.NOTE 1Pipe fabricated with polymeric coated sheet may be used forsanitary sewers and industrial applications.NOTE 2This specification is a manufacturing specification and pur-chase specification only and does not in

7、clude requirements for backfill, orthe relationship between field load conditions.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guide

8、s and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:A153/A153M Specification for Zinc Coating (Hot-Dip) onIron and Steel HardwareA563 Specification for Carbon and Alloy Steel NutsA615/A615M Specification f

9、or Deformed and Plain Carbon-Steel Bars for Concrete ReinforcementA742/A742M Specification for Steel Sheet, Metallic Coatedand Polymer Precoated for Corrugated Steel PipeA760/A760M Specification for Corrugated Steel Pipe,Metallic-Coated for Sewers and DrainsA762/A762M Specification for Corrugated St

10、eel Pipe, Poly-mer Precoated for Sewers and DrainsA885/A885M Specification for Steel Sheet, Zinc and Ar-amid Fiber Composite Coated for Corrugated Steel Sewer,Culvert, and Underdrain Pipe (Withdrawn 2006)2A929/A929M Specification for Steel Sheet, Metallic-Coatedby the Hot-Dip Process for Corrugated

11、Steel PipeB633 Specification for Electrodeposited Coatings of Zinc onIron and SteelB695 Specification for Coatings of Zinc Mechanically De-posited on Iron and SteelC33/C33M Specification for Concrete AggregatesC39/C39M Test Method for Compressive Strength of Cylin-drical Concrete SpecimensC150/C150M

12、 Specification for Portland CementC309 Specification for Liquid Membrane-Forming Com-pounds for Curing ConcreteC497 Test Methods for Concrete Pipe, Manhole Sections, orTileC595/C595M Specification for Blended Hydraulic CementsC618 Specification for Coal Fly Ash and Raw or CalcinedNatural Pozzolan fo

13、r Use in Concrete1This test method is under the jurisdiction of ASTM Committee A05 onMetallic-Coated Iron and Steel Products and is the direct responsibility ofSubcommittee A05.17 on Corrugated Steel Pipe Specifications.Current edition approved Nov. 1, 2017. Published December 2017. DOI:10.1520/A110

14、517.2The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles

15、on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1C1619 Specification for Elastomeric Seals for Joining Con-crete StructuresD1056 S

16、pecification for Flexible Cellular MaterialsSponge or Expanded Rubber2.2 AASHTO Standards:3T241 Test for Helical Continuous Welded Seam CorrugatedSteel PipeT249 Test for Helical Lock Seam Corrugated Pipe3. Terminology3.1 Definitions:For definitions of terms relating to pre-fabricated steel reinforce

17、d manholes, see Terminology A760/A760M.4. Materials and Manufacture4.1 Steel Sheet for Manhole Structure(s) PipeAll pipefabricated under this specification shall be formed from zinc-coated sheet, aluminum-coated sheet, 55 % aluminum-zincalloy-coated sheet, zinc-5 % aluminum-mischmetal alloy-coated s

18、heet all conforming to Specification A929/A929M,zinc-coated sheet conforming to Specification A885/A885M,or polymer precoated sheet meeting A762/A762M . If the typeof metallic coating is not stated in the order, zinc-coated sheetconforming to Specification A929/A929M shall be used. Allpipe furnished

19、 on the order shall have the same metalliccoating, unless otherwise specified.4.2 Steel Sheet for Coupling BandsThe sheets used infabricating coupling bands shall have the same coating andshall conform to the same specification listed in 4.1 as that usedfor fabrication of the manhole assembly(s)pipe

20、 furnished underthe order.4.3 RivetsThe rivets used in riveted pipe shall be of thesame material as the base metal specified for the corrugatedsheets. They shall be thoroughly galvanized. If bolts and nutsare substituted for rivets (see 4.4.1), they shall meet thefollowing requirements:Bolts NutsFor

21、 A760 pipe A449 A563, Grade CFor A760M SI pipe F568M, Class 8.8 A563M, Class 12The bolts and nuts shall be hot-dip galvanized in confor-mance with Specification A153/A153M, or be mechanicallygalvanized in conformance with Specification B695, Class 40.4.4 Hardware for Joining SystemsBolts and nuts fo

22、rcoupling bands shall conform to the following requirements:Bolts NutsFor A760 pipe A307 A563, Grade AFor A760M pipe F568M, Class 4.6 A563M, Class 54.4.1 Bolts, nuts, and other threaded items used with joiningsystems shall be zinc coated by one of the following processes:hot-dip process as provided

23、in Specification A153/A153M;electroplating process as provided in Specification B633, ClassFe/Zn 8; or mechanical process as provided in SpecificationB695, Class 8. Other hardware items used with coupling bandsshall be zinc coated by one of the following processes: hot-dipprocess as provided in Spec

24、ification A153/A153M; electroplat-ing process as provided in Specification B633, Class Fe/Zn 25;or mechanical process as provided in Specification B695, Class25.4.5 GasketsIf gaskets are used in joining systems, theyshall be a band of expanded rubber meeting the requirements ofSpecification D1056 fo

25、r the “RE” closed-cell grades, orO-rings meeting the requirements of Specification C1619.4.6 Metallic-Coated Steel InsertsMetallic-coated steel in-serts for Type IS and Type IIS pipe shall be of the samematerial specified for the pipe in 4.1 and shall have a metalliccoating of the same type and coat

26、ing weight. In addition tothese requirements, when specified in the order, the metallic-coated steel insert shall be fabricated from polymer precoatedsheet conforming to Specification A742/A742M.4.7 Steel Reinforced ConcreteReinforced concrete shallconsist of cementitious materials, mineral aggregat

27、es, andwater, in which steel reinforcement has been embedded orcontained in such a manner so that the steel and reinforcementact together.4.7.1 CementCement shall conform to the requirementsfor Portland cement Specifications C150/C150M, or shall bePortland blast-furnace slag cement or portland-pozzo

28、lan ce-ment conforming to Specifications C595/C595M, except thatthe pozzolan constituent of the Type IP portland-pozzolancement shall be fly ash and shall not exceed 25% by weight.4.7.1.1 Fly AshFly Ash shall conform to the requirementsof Class F or Class C of Specifications C618.4.7.2 Allowable Com

29、binations of Cementious MaterialsThe combination of cementious materials used in the concreteshall be one of the following.4.7.2.1 Portland cement only,4.7.2.2 Portland blast-furnace slag cement only,4.7.2.3 Portland pozzolan cement only, or4.7.2.4 A combination of portland cement and fly ash isbetw

30、een 5 and 25 % by weight of total cementitious materials(Portland cement plus fly ash).4.7.3 AggregatesAggregates shall conform to Specifica-tions C33/C33M, except that the requirements of gradationshall not apply.4.7.4 Admixtures and BlendsAdmixtures or blends shallnot be used unless approved by th

31、e owner.4.7.5 Steel ReinforcementReinforcement shall consist ofbars of Grade 40 steel conforming to Specifications A615/A615M.4.7.6 Other MaterialsOther materials required for a prod-uct and not covered in Section 4 will be covered in Part IIsection for that product.5. Design5.1 Design requirements

32、for a product are prescribed in thespecific Part II section for that product.5.1.1 The minimum compressive strength of compositecorrugated steel/concrete manhole products covered by thisspecification shall be 4000 psi unless specified otherwise inPart II of the specification.5.2 Modified or Special

33、Design:3Available from American Association of State Highway and TransportationOfficials (AASHTO), 444 N. Capitol St., NW, Suite 249, Washington, DC 20001,http:/www.transportation.org.A1105 1725.2.1 Manufactures are not prohibited from submitting tothe owner, for approval prior to manufacture, desig

34、ns otherthan those prescribed in the specific section for a product. Ifsuch approval is obtained, then the product shall meet all thetests and performance requirements specified by the owner inaccordance with the appropriate sections of manufactures andphysical requirements.5.2.2 If permitted by the

35、 owner, the manufacturer is notprohibited from requesting approval of designs of specialsections, such as reducers, tees, and base.6. Reinforcement6.1 This section presents requirements for reinforcementcover, continuity, laps, welds and splices. Other reinforcementrequirements are presented in Sect

36、ion 4, and any additionalrequirements are given in Part II section for a specific product.6.2 CoverThe exposure of the ends of reinforcement,stirrups or spacers used to position the reinforcement duringplacement of the concrete shall not be cause for rejection.6.3 ContinuityThe continuity of the cir

37、cumferential rein-forcement shall not be destroyed during the manufacture of theproduct, except when pipe openings are provided in theproduct.6.4 Welded Steel Reinforcement Laps, Welds, and Splices:6.4.1 If splices are not welded, the reinforcement shall belapped not less than 20 diameters for defor

38、med bars, and 40diameters for plain bar and cold-drawn wire.6.4.2 When splices are welded and are not lapped to theminimum requirements in 6.4.1 pull tests of representativespecimens shall develop at least 50% of the minimum specifiedtensile strength of steel, and there shall be a minimum lap of2 in

39、. For butt welded splices in bars, permitted only withhelically wound cages, pull tests of representative specimensshall develop at least 75% of the minimum specified tensilestrength of the steel.7. Cast-in-Place Concrete Manufacture7.1 MixtureThe aggregate shall be sized, graded,proportioned, and m

40、ixed with such proportions of cementitiousmaterials and water as will produce a homogeneous concretemixture of such quality that the products will conform to thetest and design requirements of this specification. All concreteshall have a water-to-cement ratio not exceeding 0.53 byweight. Cementitiou

41、s materials shall be as specified in 4.7.1and shall be added to the mix in a proportion of not less than470 lb/yd3, unless mix designs with lower cementitious mate-rials content demonstrate that the quality and performance ofthe product meet the requirements of this specification.7.2 CuringConcrete

42、products shall be subjected to anyone of the methods prescribed in 7.2.1 7.2.3 or to any othermethods or combination of methods approved by the ownerthat will give satisfactory results.7.2.1 Water CuringConcrete products are water-cured bycovering with water-saturated, or by any other approvedmethod

43、 that will keep products moist during the curing period.7.2.2 Sealing MembraneA sealing membrane conformingto the requirements of Specifications C309 is applied and shallbe left intact until the required concrete strength requirementsare met. The concrete at the time of the application of themembran

44、e shall be within 10 F of the atmospheric tempera-ture. All concrete surfaces shall be kept moist prior to theapplication of the membrane is applied.7.2.3 The manufacturer is not prohibited from combiningthe methods prescribed in 7.2.1 and 7.2.2 provided the requiredconcrete compressive strength is

45、attained.8. Acceptance8.1 Acceptance Procedures:8.1.1 Unless otherwise designated by the owner at the timeof, or before, placing an order, acceptance procedures forcast-in-place reinforced concrete manhole products shall not beas specified in the Part II section for a particular product, andshall no

46、t be prohibited from consisting of one or more of thefollowing:8.1.1.1 Acceptance of a product on the basis of tests ofmaterials includes concrete compressive strength.8.1.1.2 Acceptance of a product on the basis of inspection ofthe finished product, including amount and placement ofreinforcement to

47、 determine conformance with the designprescribed under this specification, and freedom from defects.8.2 Test Methods:8.2.1 Concrete Compressive Strength Test:8.2.1.1 Type of SpecimenCompression tests for satisfyingthe minimum specified concrete strength requirements shall bemade on either concrete c

48、ylinders or at the option of themanufacturer from the concrete manhole product.8.2.1.2 Compression Testing of CylindersCylinders shallbe made in accordance with the Test Methods C497, and shallbe tested in accordance with C39/C39M. For manholeproducts, an owner shall not be prohibited from requiring

49、concrete compressive tests on cylinder specimens numberingin the amount of 5% of the total order of a manhole product,but not to exceed two cylinders for each days production. Theaverage compressive strength of all cylinders tested shall beequal to or greater than the specified strength of the concrete.Not more than 10% of the cylinders tested shall fall below thespecified strength of the concrete. In no case shall any cylindertested fall below 80% of the specified strength.8.2.1.3 Compressive Testing of CoresCores shall be cutfrom the concret