ASTM A353 A353M-2009 Standard Specification for Pressure Vessel Plates Alloy Steel Double-Normalized and Tempered 9% Nickel《压力容器用经二次正火及回火处理的含9％镍的合金钢板标准规范》.pdf

1、Designation: A353/A353M 09Standard Specification forPressure Vessel Plates, Alloy Steel, Double-Normalized andTempered 9 % Nickel1This standard is issued under the fixed designation A353/A353M; the number immediately following the designation indicates the yearof original adoption or, in the case of

2、 revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification2covers double-normalized and tem-pered 9 % nickel steel plates intended par

3、ticularly for weldedpressure vessels for cryogenic service.1.2 Plates produced under this specification are subject toimpact testing at 320F 195C or at such other tempera-tures as are agreed upon.1.3 The maximum thickness of plates is limited only by thecapacity of the material to meet the specific

4、mechanicalproperty requirements; however, current mill practice normallylimits this material to 2 in. 50 mm max.1.4 This material is susceptible to magnetization. Use ofmagnets in handling after heat treatment should be avoided ifresidual magnetism would be detrimental to subsequent fabri-cation or

5、service.1.5 The values stated in either inch-pound units or SI unitsare to be regarded separately as standard. Within the text, theSI units are shown in brackets. The values stated in eachsystem are not exact equivalents; therefore, each system mustbe used independently of the other. Combining value

6、s from thetwo systems may result in nonconformance with the specifi-cation.2. Referenced Documents2.1 ASTM Standards:3A20/A20M Specification for General Requirements forSteel Plates for Pressure VesselsA435/A435M Specification for Straight-Beam UltrasonicExamination of Steel PlatesA553/A553M Specifi

7、cation for Pressure Vessel Plates, Al-loy Steel, Quenched and Tempered 8 and 9 % NickelA577/A577M Specification for Ultrasonic Angle-Beam Ex-amination of Steel PlatesA578/A578M Specification for Straight-Beam UltrasonicExamination of Rolled Steel Plates for Special Applica-tions3. General Requiremen

8、ts and Ordering Information3.1 Material supplied to this material specification shallconform to Specification A20/A20M. These requirements out-line the testing and retesting methods and procedures, permit-ted variations in dimensions, and mass, quality and repair ofdefects, marking, loading, and ord

9、ering information.3.2 In addition to the basic requirements of this specifica-tion, certain supplementary requirements are available whenadditional control, testing, or examination is required to meetend use requirements. The purchaser is referred to the listedsupplementary requirements in this spec

10、ification and to thedetailed requirements in Specification A20/A20M.3.3 If the requirements of this specification are in conflictwith the requirements of SpecificationA20/A20M, the require-ments of this specification shall prevail.4. Manufacture4.1 Steelmaking PracticeThe steel shall be killed andsh

11、all conform to the fine austenitic grain size requirement ofSpecification A20/A20M.5. Heat Treatment5.1 All plates shall be heat treated in accordance with 5.2.Shell plates and other parts, including heads and reinforcingpads that are heated for forming shall be heat treated afterforming in accordan

12、ce with 5.2.5.2 Heat Treatment Procedure:5.2.1 First Normalizing TreatmentHeat the plate to auniform temperature of 1650 6 25F 900 6 15C, hold atthat temperature for a minimum of 1 h/in. 2.4 min/mm ofthickness, but in no case less than 15 min, and cool in air.5.2.2 Second Normalizing TreatmentReheat

13、 the plate to auniform temperature of 1450 6 25F 790 6 15C, hold atthat temperature for a minimum of 1 h/in. 2.4 min/mm ofthickness, but in no case less than 15 min, and cool in air.1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is

14、 the direct responsibility of SubcommitteeA01.11 on Steel Plates for Boilers and Pressure Vessels.Current edition approved Oct. 1, 2009. Published November 2009. Originallyapproved in 1952. Last previous edition approved in 2004 as A353/A353M 04.DOI: 10.1520/A0353_A0353M-09.2For ASME Boiler and Pres

15、sure Vessel Code applications, see related Specifi-cation SA-353/SA-353M in Section II of that Code.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Do

16、cument Summary page onthe ASTM website.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.2.3 Tempering TreatmentReheat the plate to a uniformtemperature within the ran

17、ge from 1050 to 1125F 565 to605C, hold within that temperature range for a minimum of1 h/in. 2.4 min/mm of thickness, but in no case less than 15min, and cool in air or water quench at a rate not less than300F/h 165C/h.5.2.4 If hot forming is performed after heating to a tempera-ture within the rang

18、e from 1650 to 1750F 900 to 955C thefirst normalizing treatment (5.2.1) may be omitted.5.2.5 When the plates are heat treated by the fabricator, itshall be the fabricators responsibility to apply the proper heattreatment and to conduct tests it deems necessary to ensure thatthe specified properties

19、are attained.6. Chemical Requirements6.1 The steel shall conform to the chemical compositionrequirements shown in Table 1 unless otherwise modified inaccordance with Supplementary Requirement S17, VacuumCarbon-Deoxidized Steel, in Specification A20/A20M.7. Mechanical Requirements7.1 Tension Test Req

20、uirementsThe material as representedby the tension-test specimens shall conform to the require-ments specified in Table 2.7.1.1 Upon agreement between the purchaser and the manu-facturer, yield strength may be determined by the extensionunder load method, using 0.005 in./in. 0.005 mm/mm totalextensi

21、on.7.1.2 For nominal plate thicknesses of34 in. 20 mm andunder, the 112-in. 40-mm wide rectangular specimen may beused for the tension test and the elongation may be determinedin a 2-in. 50-mm gage length that includes the fracture andshows the greatest elongation.7.1.3 One tension test shall be tak

22、en from each plate as heattreated.7.2 Impact Test Requirements:7.2.1 Charpy V-notch impact tests shall be made in accor-dance with Specification A20/A20M.7.2.2 The longitudinal axis of the test specimens shall betransverse to the final rolling direction of the plate.7.2.3 Unless otherwise agreed, te

23、sts shall be conducted at320F 195C.7.2.4 Each test specimen shall have a lateral expansionopposite the notch of not less than 0.015 in. 0.381 mm.8. Finish8.1 Because retained scale may mask surface imperfections,as well as mar the plate surface, plates shall be descaled by theproducer after heat tre

24、atment. In the case of material to beheat-treated by the purchaser, the plates shall be descaled bythe producer prior to shipment.9. Keywords9.1 alloy steel; alloy steel plate; pressure containing parts;pressure vessel steels; steel plates; steel plates for pressurevessel applicationsSUPPLEMENTARY R

25、EQUIREMENTSSupplementary requirements shall not apply unless specified in the order.Alist of standardized supplementary requirements for use at the option of the purchaser are includedin Specification A20/A20M. Several of those considered suitable for use with this specification arelisted below by t

26、itle. Other tests may be performed by agreement between the supplier and thepurchaser.S1. Vacuum Treatment,S2. Product Analysis,S4.1 Additional Tension Test,S6. Drop Weight Test,S8. Ultrasonic Examination in Accordance with Specifi-cation A435/A435M,S11. Ultrasonic Examination in Accordance with Spe

27、cifica-tion A577/A577M,S12. Ultrasonic Examination in Accordance with Specifica-tion A578/A578M, andS17. Vacuum Carbon-Deoxidized Steel.TABLE 1 Chemical RequirementsElement Composition, %Carbon, maxA0.13Manganese, maxHeat analysisProduct analysis0.900.98Phosphorus, maxA0.015Sulfur, maxA0.015Silicon:

28、Heat analysisProduct analysis0.150.40B0.130.45BNickel:Heat analysisProduct analysis8.509.508.409.60AApplies to both heat and product analyses.BThe specified minimum limit does not apply if the total aluminum content is0.030 % or more, or provided that acid soluble aluminum is 0.025 % or more.TABLE 2

29、 Tensile RequirementsTensile strength, ksi MPa 100120 690825Yield strength (0.2 % offset), min, ksi MPaA75 515Elongation in 2 in. 50 mm, min, %B20.0ASee 7.1.1.BSee Specification A20/A20M for elongation adjustment.A353/A353M 092ADDITIONAL SUPPLEMENTARY REQUIREMENTSAlso listed below are additional opt

30、ional Supplementary Requirements S55 and S56, which aresuitable for this specification.S55. Longitudinal Charpy Impact Energy AbsorptionRequirementS55.1 The longitudinal Charpy V-notch impact propertiesshall not be less than 25 ftlbf 34 J at the specified tempera-ture.S55.2 Each impact-test value sh

31、all constitute the averagevalue of three specimens, with not more than one value belowthe specified minimum value of 25 ftlbf 34 J, but in no casebelow 20 ftlbf 27 J for full size specimens.S56. Transverse Charpy Impact Energy AbsorptionRequirementS56.1 The transverse Charpy V-notch impact propertie

32、sshall not be less than 20 ftlbf 27 J at the specified tempera-ture.S56.2 Each impact-test value shall constitute the averagevalue of three specimens, with not more than one value belowthe specified minimum value of 20 ftlbf 27 J but in no casebelow 15 ftlbf 20 J for full-size specimens.SUMMARY OF C

33、HANGESCommittee A01 has identified the location of selected changes to this standard since the last issue(A353/A353M 04) that may impact the use of this standard. (Approved Oct. 1, 2009.)(1) Title and 1.1 revised to be more in agreement withA553/A553M.(2) Section 2 editorially revised.(3) 3.2 and 3.

34、4 deleted and content incorporated into 3.1 and3.2, respectively. 3.3.13.3.4 deleted as unnecessary. Sectionparagraphs subsequently renumbered.(4) 5.2.2 and 5.2.3 editorially corrected to bracket SI units.(5) Reference to S3 deleted from Supplementary Require-ments (not commonly if ever specified fo

35、r this specification).(6) Table 1 revised to reflect modern steel requirements.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the vali

36、dity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comm

37、ents are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have

38、not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple c

39、opies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).A353/A353M 093