ASTM B173-2010(2015) Standard Specification for Rope-Lay-Stranded Copper Conductors Having Concentric-Stranded Members for Electrical Conductors《电导线用同芯绞绳铜导线的标准规格》.pdf

1、Designation: B173 10 (Reapproved 2015)Standard Specification forRope-Lay-Stranded Copper Conductors Having Concentric-Stranded Members, for Electrical Conductors1This standard is issued under the fixed designation B173; the number immediately following the designation indicates the year oforiginal a

2、doption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Def

3、ense.1. Scope1.1 This specification covers bare rope-lay-stranded con-ductors having concentric-stranded members made from roundcopper wires, either uncoated or coated with tin, lead, orlead-alloy for use as electrical conductors (Explanatory Note 1and Note 2).1.2 Coated wires shall include only tho

4、se wires with fin-ished diameters and densities substantially equal to the respec-tive diameters and densities of uncoated wires.1.3 The values stated in inch-pound or SI units are to beregarded separately as standard. Each system shall be usedindependently of the other. Combining values from the tw

5、osystems may result in nonconformance with the specification.For conductor sizes designated by AWG or kcmil, the require-ments in SI units have been numerically converted fromcorresponding values, stated or derived, in inch-pound units.For conductor sizes designated by SI units only, the require-men

6、ts are stated or derived in SI units.1.3.1 For density, resistivity, and temperature, the valuesstated in SI units are to be regarded as standard.2. Referenced Documents2.1 The following documents of the issue in effect at thetime of reference form a part of this specification to the extentreference

7、d herein:2.2 ASTM Standards:2B3 Specification for Soft or Annealed Copper WireB8 Specification for Concentric-Lay-Stranded CopperConductors, Hard, Medium-Hard, or SoftB33 Specification for Tin-Coated Soft or Annealed CopperWire for Electrical PurposesB172 Specification for Rope-Lay-Stranded Copper C

8、onduc-tors Having Bunch-Stranded Members, for Electrical Con-ductorsB189 Specification for Lead-Coated and Lead-Alloy-CoatedSoft Copper Wire for Electrical PurposesB193 Test Method for Resistivity of Electrical ConductorMaterialsB263 Test Method for Determination of Cross-SectionalArea of Stranded C

9、onductorsB354 Terminology Relating to Uninsulated Metallic Electri-cal Conductors2.3 American National Standard:ANSI C42.35 Definitions of Electrical Terms33. Classification3.1 For the purpose of this specification rope-lay-strandedconductors having concentric-stranded members are classifiedas follo

10、ws:3.1.1 Class GConductors consisting of 7 to 61 rope-lay-stranded members, each of which consists of 7 to 19concentric-stranded wires, with total conductor sizes rangingfrom No. 14 AWG (2.08 mm2) to 5 000 000 cmil (2534 mm2).(Typical use is for rubber-sheathed conductor, apparatusconductor, portabl

11、e conductor, and similar applications.)3.1.2 Class HConductors consisting of 19 to 91 rope-lay-stranded members, each of which consists of 7 to 19concentric-stranded wires, with total conductor sizes rangingfrom No. 9 AWG (6.63 mm2) to 5 000 000 cmil (2534 mm2).Class K construction produces a conduc

12、tor with greater flex-ibility than class G. (Typical use is for rubber-sheathed cordand applications where flexibility is required such as ontake-up reels over sheaves and extra-flexible apparatus con-ductor.)4. Ordering Information4.1 Orders for material under this specification shall includethe fo

13、llowing information:1This specification is under the jurisdiction of ASTM Committee B01 onElectrical Conductors and is the direct responsibility of Subcommittee B01.04 onConductors of Copper and Copper Alloys.Current edition approved April 1, 2015. Published April 2015. Originallyapproved in 1942 to

14、 replace portions of B158 41 T. Last previous edition approvedin 2010 as B173 10. DOI: 10.1520/B0173-10R15.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the stand

15、ards Document Summary page onthe ASTM website.3Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States14.1.1 Quantit

16、y of each size and class;4.1.2 Conductor size: circular-mil area or AWG (Section 7);4.1.3 Class (Section 3 and Tables 1 and 2);4.1.4 Whether coated or uncoated; if coated, designate typeof coating (see 11.1);4.1.5 Details of special-purpose lays, if required (see 6.2and 6.3) and (Explanatory Note 3)

17、;4.1.6 Package size (see 14.1);4.1.7 Special package marking, if required (Section 15);4.1.8 Lagging, if required (see 14.2); and4.1.9 Place of inspection (Section 13).5. Joints5.1 Necessary joints in wires or in groups of wires shall bemade in accordance with accepted commercial practice, takingint

18、o account the size of the wire or group of wires as related tothe size of the entire conductor.5.2 Concentric-stranded members forming the completedconductor may be joined as a unit by soldering, brazing, orwelding.5.3 Joints shall be so constructed and so disposed through-out the conductor that the

19、 diameter or configuration of thecompleted conductor is not substantially affected, and so thatthe flexibility of the completed conductor is not adverselyaffected.6. Lay (Explanatory Note 3)6.1 Conductors of the same size and description furnishedon one order shall have the same lay.6.2 The length o

20、f lay of the outer layer of the rope-laystranded conductor shall be not less than 8 nor more than 16times the outside diameter of the completed conductor. Thelength of lay of the other layers shall be at the option of themanufacturer unless specifically agreed upon. The direction oflay of the outer

21、layer shall be left-hand, unless the direction oflay is specified otherwise by the purchaser. The direction of layof the other layers shall be reversed in successive layers, unlessotherwise agreed upon between the manufacturer and thepurchaser.6.3 The length of lay of the individual wires composing

22、thestranded members shall be not less than 8 nor more than 16times the outside diameter of that layer. Unless otherwisespecified, the direction of lay of the outer layer of wires shallbe at the option of the manufacturer. The direction of lay shallbe reversed in successive layers, unless otherwise a

23、greed uponbetween the manufacturer and the purchaser.7. Construction7.1 The area of cross section and the number and diameterof wires for a variety of strand constructions in general use areshown in Tables 1 and 2.8. Physical and Electrical Tests8.1 Tests for the electrical properties of wires compo

24、singconductors made from soft or annealed copper wire, bare orcoated, shall be made before stranding.8.2 Tests for the physical properties of soft or annealedcopper wire, bare or coated, may be made upon the wiresbefore stranding or upon wires removed from the completedstranded conductors, but need

25、not be made upon both. Careshall be taken to avoid mechanical injury and stretching whenremoving wires from the conductor for the purpose of testing.8.3 The physical properties of wire when tested beforestranding shall conform to the applicable requirements of 11.1.8.4 The physical properties of wir

26、es removed from thecompleted stranded conductor shall be permitted to vary fromthe applicable requirements of 11.1 by the following amounts:(Explanatory Note 4):8.4.1 Average of Results Obtained on All Wires TestedThepercent minimum elongation may be reduced by the value of5 % from the values requir

27、ed for unstranded wires as specifiedby Specifications B3, B33,orB189, as applicable. Forexample, where the unstranded wire specification requiresminimum elongation of 30 %, wire of that material removedfrom Specification B173 stranded conductor shall meet aminimum elongation value of 25 %, a value 5

28、 % reduction.8.4.2 Results Obtained on Individual WiresThe percentminimum elongation may be reduced by the value of 15 %from the values required for unstranded wires as specified bySpecifications B3, B33,orB189, as applicable. For example,where the unstranded wire specification requires minimumelong

29、ation of 30 % wire of that material removed fromSpecification B173 stranded conductor shall meet a minimumelongation value of 15 %. If the reduction results in minimumelongation of less than 5 %, a minimum of 5 % shall apply.8.5 In the event that the requirements prescribed in 8.4.2 aremet, but thos

30、e prescribed in 8.4.1 are not met, a retest shall bepermitted wherein all wires of a conductor of 100 wires or less,or 100 wires selected at random throughout a conductor ofmore than 100 wires shall be tested for the purpose of finaldetermination for conformance to 8.4.8.6 Elongation tests to determ

31、ine compliance shall not bemade on the conductor as a unit.8.7 If a tinning, lead-coating, or lead-alloy-coating test isrequired, it shall be made on the wires prior to stranding.9. Density9.1 For the purpose of calculating mass, cross sections, etc.,the density of copper shall be taken as 8.89 g/cm

32、3(0.32117lb/in.3) at 20C (Explanatory Note 5).10. Mass and Resistance10.1 The mass and electrical resistance of a unit length ofstranded conductor are a function of the length of lay. Theapproximate mass and electrical resistance may be determinedusing the standard increments shown in Explanatory No

33、te 6.When greater accuracy is desired, the increment based on thespecific lay of the conductor may be calculated (ExplanatoryNote 7).10.2 The maximum electrical resistance of a unit ofstranded conductor shall not exceed 2 % over the nominal DCresistance shown in Table 1 and Table 2. When the DCB173

34、10 (2015)2TABLE1ConstructionalandDCResistanceRequirementsofRope-LayStrandedCopperConductorsHavingConcentric-StrandedMembersClassGAAreaofCrossSectionSizeAWGCompletedConductorBUncoatedCopperTinnedCopperNumberofWiresDiameterofWiresNumberofWiresinEachMemberNominalDiameterNominalMassNominalDCResistance20

35、CMaximumDCResistance20CNominalDCResistance20CMaximumDCResistance20Ccmilmm2in.mmin.mmlb/1000ftkg/kmohm/1000ftohm/kmohm/1000ftohm/kmohm/1000ftohm/kmohm/1000ftohm/km50000002534.11590.06571.67192.95775.116052238880.002200.007210.002240.007350.002290.007500.002340.0076545000002280.11590.06231.58192.80471

36、.214433214790.002440.008010.002490.008170.002540.008330.002590.0085040000002027.11590.05871.49192.64267.112814190690.002750.009020.002810.009200.002860.009380.002920.0095735000001773.11590.05501.40192.47562.911249167410.003140.01030.003200.01050.003270.01070.003340.010930000001520.11590.05091.29192.

37、29158.29635143380.003660.01200.003730.01220.003810.01250.003890.012825000001267.7030.05961.51192.08653.08012119240.004400.01440.004490.01470.004570.01500.004660.015320000001013.7030.05331.35191.86647.4640895360.005500.01800.005610.01840.005720.01880.005830.01921900000963.7030.05201.32191.82046.26099

38、90770.005790.01900.005910.01940.006020.01970.006140.02011800000912.7030.05061.29191.77145.0577585940.006110.02000.006230.02040.006350.02080.006480.02121750000887.7030.04991.27191.74744.4561783580.006280.02060.006410.02100.006530.02140.006660.02181700000861.7030.04921.25191.72243.7546081250.006470.02

39、120.006600.02160.006720.02210.006850.02251600000811.7030.04771.21191.67042.4513276380.006870.02250.007010.02300.007150.02340.007290.02391500000760.4270.05931.5171.60140.7477271020.007260.02380.007410.02430.007550.02480.007700.02531400000709.4270.05731.4671.54739.3445666310.007780.02550.007940.02600.

40、008090.02650.008250.02701300000659.4270.05521.4071.49037.8413561540.008380.02750.008550.02810.008710.02860.008880.02921250000633.4270.05411.3771.46137.1397259110.008710.02860.008880.02920.009060.02970.009240.03031200000608.4270.05301.3571.43136.3381256730.009070.02980.009250.03040.009440.03100.00963

41、0.03161100000557.4270.05081.2971.37234.8350252120.009900.03250.01010.03320.01030.03380.01050.03451000000507.4270.04841.2371.30733.2317947310.010900.03570.01110.03640.01130.03720.01150.0379900000456.4270.04591.1771.23931.5285942550.01210.03970.01230.04050.01260.04130.01290.0421800000405.4270.04331.10

42、71.16929.7254437870.01360.04470.01390.04560.01420.04640.01450.0473750000380.4270.04191.0671.13128.7238335460.01450.04760.01480.04860.01510.04950.01540.0505700000355.4270.04051.0371.09427.8222633130.01560.05100.01590.05200.01620.05310.01650.0542650000329.4270.03900.9971.05326.7206430720.01680.05500.0

43、1710.05610.01740.05720.01770.0583600000304.4270.03750.9571.01325.7190828400.01810.05950.01850.06070.01890.06190.01930.0631550000279.4270.03590.9170.96924.6174926030.01980.06500.02020.06630.02060.06760.02100.0690500000253.2590.04391.1270.92223.4157923500.02170.07110.02210.07250.02250.07400.02300.0755

44、450000228.2590.04171.0670.87622.3142521200.02410.07900.02460.08060.02510.08220.02550.0838400000203.2590.03931.0070.82521.0126518830.02710.08890.02760.09070.02820.09240.02880.0942350000177.2590.03680.9370.77319.6110916510.03100.1020.03160.1040.03220.1060.03280.108300000152.2590.03400.8670.71418.19471

45、4090.03610.1190.03680.1210.03760.1230.03840.125250000127.2590.03110.7970.65316.679211790.04340.1420.04430.1450.04510.1480.04600.15121160010700001330.03991.0170.59915.26679920.05100.1670.05200.1700.05300.1740.05410.17716780085.00001330.03550.9070.53313.55287850.06430.2110.06560.2150.06680.2190.06810.

46、22313310067.4001330.03160.8070.47412.04186220.08100.2660.08260.2710.08430.2760.08600.28210560053.501330.02820.7270.42310.73334950.1020.3350.1040.3420.1060.3480.1080.3558369042.411330.02510.6470.3779.62643930.1290.4230.1320.4310.1340.4400.1370.4496636033.62490.03680.9370.3318.42073080.1610.5280.1640.

47、5390.1670.5490.1700.5605262026.73490.03280.8370.2957.51642450.2030.6660.2070.6790.2110.6930.2150.7074174021.14490.02920.7470.2636.71301940.2560.8400.2610.8570.2660.8730.2710.8903309016.85490.02600.6670.2345.91031540.3231.060.3291.080.3361.100.3431.122624013.36490.02310.5970.2085.381.51210.4071.340.4

48、151.370.4231.390.4311.422082010.57490.02060.5270.1854.764.896.50.5131.680.5231.710.5341.750.5451.79165108.378490.01840.4770.1664.251.777.00.6472.120.6602.160.6872.250.7012.30130906.639490.01630.4170.1483.840.660.40.8162.680.8322.730.8672.840.8842.90103805.2610490.01460.3770.1313.332.648.51.033.381.0

49、53.451.093.591.113.66B173 10 (2015)3TABLE1ContinuedAreaofCrossSectionSizeAWGCompletedConductorBUncoatedCopperTinnedCopperNumberofWiresDiameterofWiresNumberofWiresinEachMemberNominalDiameterNominalMassNominalDCResistance20CMaximumDCResistance20CNominalDCResistance20CMaximumDCResistance20Ccmilmm2in.mmin.mmlb/1000ftkg/kmohm/1000ftohm/kmohm/1000ftohm/kmohm/1000ftohm/kmohm/1000ftohm/km65303.3112490.01150.2970.1042.620.230.11.645.371.675.481.745.701.775.8141102.0814490.00920.2370.0832.112.919.22.608.532.658