ASTM C1264-2011 Standard Specification for Sampling Inspection Rejection Certification Packaging Marking Shipping Handling and Storage of Gypsum Panel Products《石膏心墙板制品的抽样 检验 淘汰 合格认.pdf

1、Designation: C1264 11Standard Specification forSampling, Inspection, Rejection, Certification, Packaging,Marking, Shipping, Handling, and Storage of Gypsum PanelProducts1This standard is issued under the fixed designation C1264; the number immediately following the designation indicates the year ofo

2、riginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers sampling; inspection; rejec-tion;

3、certification; packaging and marking; and shipping, han-dling, and storage of gypsum panel products.2. Referenced Documents2.1 ASTM Standards:2C11 Terminology Relating to Gypsum and Related BuildingMaterials and SystemsC1396/C1396M Specification for Gypsum Board2.2 ISO Standards:3ISO 31661 Codes for

4、 the representation of names ofcountries and their subdivisions - Part 1: Country codes3. Terminology3.1 DefinitionsDefinitions shall be in accordance withTerminology C11.4. Sampling4.1 When specified by the purchase agreement, samples ofgypsum panel products shall be taken at the place of manufac-t

5、ure or at the destination. If the samples are taken at thedestination, such samples shall be taken within 24 h of thereceipt of the material.4.2 At least 0.25 % of the number of gypsum panel productsin a shipment, but not less than three gypsum panel products,shall be so selected as to be representa

6、tive of the shipment andshall constitute a sample for the purpose of tests by thepurchaser or user.5. Inspection5.1 Inspection of the gypsum panel products shall be agreedupon between the purchaser and the producer or supplier aspart of the purchase agreement.6. Rejection6.1 Rejection of gypsum pane

7、l products that fails to con-form to the requirements of the specification shall be reportedto the producer or supplier promptly and in writing. The noticeof rejection shall contain a statement documenting how thegypsum panel products has failed to conform to the require-ments of the specification.7

8、. Certification7.1 When specified in the purchase agreement, a producersor suppliers report shall be furnished at the time of shipmentcertifying that the product is in compliance with the ASTMspecification referencing this specification.8. Packaging and Marking8.1 Each gypsum panel product or packag

9、e shall havelegibly marked thereon the following: the thickness, the nameof the producer or supplier, the brand name, if any, and theASTM specification for the product.8.2 In addition to the marking described in 8.1, gypsumboard manufactured to Specification C1396/C1396M shall bemarked as described

10、in Annex A1.8.3 Single, unbound panels of gypsum board manufacturedto Specification C1396/C1396M that are packaged in multi-panel units shall be permitted to be marked as a palletizedpackaging unit. These units are typically packaged to meetspecific contractual requirements and as such the markingre

11、quirements of 8.1 and 8.2 are not applicable.9. Shipping, Handling, and Storage9.1 Gypsum panel products shall be shipped so as to be keptdry.9.2 Gypsum panel products shall be stored so as to be keptdry, preferably inside a building. Gypsum panel products shallbe neatly stacked flat with care taken

12、 to prevent sagging ordamage to edges, ends, and surfaces.1This specification is under the jurisdiction of ASTM Committee C11 onGypsum and Related Building Materials and Systems and is the direct responsibilityof Subcommittee C11.01 on Specifications and Test Methods for Gypsum Products.Current edit

13、ion approved Nov. 1, 2011. Published November 2011. Originallyapproved in 1994. Last previous edition approved in 2011 as C1264 05(2011).DOI: 10.1520/C1264-11.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of

14、ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from International Organization for Standardization (ISO), 1, ch. dela Voie-Creuse, CP 56, CH-1211 Geneva 20, Switzerland, http:/www.iso.org.1Copyright ASTM International, 100 Barr Harbor Dri

15、ve, PO Box C700, West Conshohocken, PA 19428-2959, United States.9.3 Where necessary to store gypsum panel products out-side, it shall be stacked flat, off the ground, supported on a levelplatform, and fully protected from weather and direct sunlightexposure.10. Keywords10.1 certification; gypsum; g

16、ypsum panel products; han-dling; inspection; marking; packaging; rejection; sampling;shipping; storageANNEXA1. Marking RequirementsA1.1 Each individual sheet of gypsum board manufacturedto Specification C1396/C1396M shall have the followinginformation legibly printed on the back surface:A1.1.1 The n

17、ame of the manufacturing company or aunique alpha code of not less than three letters identifying themanufacturer of the gypsum board.A1.1.2 A unique alpha or numeric code identifying themanufacturing facility and the production line.A1.1.3 Acode identifying the date and time of manufacture.A1.1.4 T

18、he three-letter alpha code as designated in ISO3166-1 identifying the country of manufacture.A1.2 The printed information described in A1.1 shall be:A1.2.1 One or more lines oriented in the machine direction,parallel to one edge of the sheet.A1.2.2 Reproduced in its entirety at an interval of not mo

19、rethan 6 ft (1800 mm) on center.A1.2.3 Placed not less than 1 in. (25 mm) nor more than 15in. (380 mm) from the edge of the sheet.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard a

20、re expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not

21、 revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which y

22、ou may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,Unite

23、d States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).C1264 112