ASTM D173 D173M-2003(2011)e1 Standard Specification for Bitumen-Saturated Cotton Fabrics Used in Roofing and Waterproofing《屋面和防水用沥青浸透棉织物标准规格》.pdf

1、Designation: D173/D173M 03 (Reapproved 2011)1Standard Specification forBitumen-Saturated Cotton Fabrics Used in Roofing andWaterproofing1This standard is issued under the fixed designation D173/D173M; the number immediately following the designation indicates the yearof original adoption or, in the

2、case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense. This standard repl

3、aces Federal SpecificationSS-C-450.1NOTEUnits information was editorially corrected in January 2012.1. Scope1.1 This specification covers woven cotton fabrics saturatedwith either asphalt or coal-tar pitch intended to be used withasphalts conforming to Specifications D312 or D449, coal-tarpitches co

4、nforming to Specification D450, or appropriatesolvent bearing bituminous materials in the construction ofroofing and waterproofing systems.1.1.1 Asphalt-saturated cotton fabric shall be used withasphalt base plying cement; typical ones are mopping asphaltsconforming to Specifications D312 or D449 or

5、 appropriatesolvent bearing asphaltic compounds.1.1.2 Coal-tar-saturated cotton fabric shall be used withcoal-tar based plying cements; a typical one is coal-tar pitchconforming to Specification D450 or appropriate solvent bear-ing coal-tar compounds.1.2 The values stated in either SI units or inch-

6、pound unitsare to be regarded separately as standard. The values stated ineach system may not be exact equivalents; therefore, eachsystem shall be used independently of the other. Combiningvalues from the two systems may result in non-conformancewith the standard.2. Referenced Documents2.1 ASTM Stan

7、dards:2D146 Test Methods for Sampling and Testing Bitumen-Saturated Felts and Woven Fabrics for Roofing and Wa-terproofingD312 Specification for Asphalt Used in RoofingD449 Specification for Asphalt Used in Dampproofing andWaterproofingD450 Specification for Coal-Tar Pitch Used in Roofing,Dampproofi

8、ng, and WaterproofingD1079 Terminology Relating to Roofing and WaterproofingD3775 Test Method for Warp (End) and Filling (Pick)Count of Woven Fabrics3. Terminology3.1 DefinitionsFor definitions of terms used in this speci-fication, refer to Terminology D1079.4. Materials and Manufacture4.1 In the pr

9、ocess of manufacture, the dry cotton fabric shallbe thoroughly and uniformly saturated with bitumen. This shallbe accomplished by passing the fabric through the saturant orby spraying with saturant, calendering in the presence of heat,and then cooling before winding on a core.4.2 If fabric with a se

10、lvage is used, the selvage shall not bemore than 16 mm 58 in. wide.4.3 The fabric shall be woven entirely from cotton fibers,but customary sizing materials not exceeding 8 % by weight ofthe moisture-free cotton shall be permitted to be used.5. Physical Properties5.1 The material shall conform to the

11、 physical requirementsprescribed in Table 1 and the dimensions and masses pre-scribed in Table 2.5.2 The finished product shall not crack nor be so sticky asto cause tearing or other damage upon being unrolled attemperatures between 10 and 60C 50 and 140F.6. Workmanship, Finish, and Appearance6.1 Th

12、e meshes of the fabric shall not be completely closedor sealed by the process of saturation. There shall be sufficientporosity maintained to allow successive moppings of theplying cement to seep through.1This specification is under the jurisdiction of ASTM Committee D08 onRoofing and Waterproofing a

13、nd is the direct responsibility of Subcommittee D08.04on Felts and Fabrics.Current edition approved Nov. 1, 2011. Published January 2012. Originallyapproved in 1923. Last previous edition approved in 2003 as D173 03. DOI:10.1520/D0173_D0173M-03R11E01.2For referenced ASTM standards, visit the ASTM we

14、bsite, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United St

15、ates.6.2 The surface of the fabric shall not be coated or coveredwith talc or other substances that would tend to interfere withadhesion between the fabric and the plying cement. The use ofsilica or wood flour is permissible.6.3 The surface shall be uniformly smooth and free ofirregularities, folds,

16、 or knots.6.4 The finished material shall be free of visible externaldefects such as ragged or untrue edges, breaks, rents, or cracks.7. Sampling and Test Methods7.1 Sample the material and determine compliance withthese specifications in accordance with Test Methods D146.7.2 Determine the pliabilit

17、y of the saturated fabric at 0C32F by bending over a 1.6-mm 116-in. diameter mandrelthrough an arc of 180 in one direction and then through 360in the opposite direction.7.3 Determine the thread count in accordance with TestMethod D3775.8. Inspection8.1 InspectionInspection shall be in accordance wit

18、h therequirements of this specification.8.2 Inspection AlternativesAlternative inspection require-ments shall be determined by and agreed upon between thepurchaser and the supplier.9. Rejection and Resubmittal9.1 Failure to ConformFailure to conform to any of therequirements as stated in this specif

19、ication constitutes groundsfor rejection.9.2 Rejection RedressThe supplier shall have the right toinspect the rejected materials. The supplier and the purchasershall agree to the quantity of rolls deemed unacceptable. Thesupplier shall then have the right to submit the same number ofnew rolls as rep

20、lacement.10. Packaging and Package Marking10.1 Unless otherwise agreed upon between the supplierand purchaser, each product package shall be plainly markedwith the suppliers name, the product brand, the ASTMdesignation, and type of bitumen if not evident in the labelname of the product.10.2 The roll

21、s shall be securely wrapped or banded in amanner that completely encircles the roll and will preventslipping or unrolling.10.3 No roll shall contain more than two pieces, and nomore than 3 % of the rolls in any lot shall contain two pieces.If a roll contains a manufacturing splice, the splice shall

22、beclearly marked.10.4 The rolls shall be wound on mandrels or rigid hollowfiber cylinders not less than 50 mm 2 in. in diameter,extending not more than 100 mm 4 in. beyond the end of therolls.11. Keywords11.1 bitumen-saturated; roofing and waterproofing; wovencotton fabricASTM International takes no

23、 position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own respons

24、ibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed t

25、o ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the add

26、ress shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone),

27、 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).TABLE 1 Physical Properties of Saturated Cotton FabricsProperty RequirementBreaking loadAat 21.

28、1C 70F, both warp and filldirections, min, kN/m lbf/in.8.76 50Pliability at 0C 32F no crackingACommittee D08 recognizes the advisability of including a requirement relativeto the percentage elongation before rupture, but in the absence of any reliable testmethod, such requirement cannot be stated at

29、 the present time.TABLE 2 Dimensions and Masses of Saturated Cotton Fabricsmin maxWidth of roll, mm in. 762 30 965 38Gross mass per roll, kg lb 15.9 35 36.3 80Mass of mandrel and wrappingmaterial, kg lb. 1.13 2.5Mass of detached comminutedsurfacing, g/m2lb/100 ft2. 49 1.0Net mass of saturated fabric

30、, avg,g/m2oz/yd2340 10 .Thread count per 25.4 mm 1 in.WarpFilling10.2 269.4 2412.6 3212.6 32Moisture, at point of manufacture,max, %A. 6.0Mass of desaturated, moisture-freefabric, avg, g/m2oz/yd2119 312 .Ash (based on mass ofdesaturated fabric), %. 2.0Mass of saturant 1.6 3 (mass ofdesaturated,moisture-freefabric in the samearea).Selvage, mm in. 16 58AAt time of manufacture, products with higher moisture content at time ofinstallation may cause hot materials to foam, creating interply voids that may resultin blisters.D173/D173M 03 (2011)12