ASTM D2466-2013 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings Schedule 40《聚氯乙烯(PVC)塑料管配件标准规格 表40》.pdf

1、Designation: D2466 13 An American National StandardStandard Specification forPoly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule401This standard is issued under the fixed designation D2466; the number immediately following the designation indicates the year oforiginal adoption or, in the case

2、 of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope*1.1 This speci

3、fication covers poly(vinyl chloride) (PVC)Schedule 40 pipe fittings. Included are requirements formaterials, workmanship, dimensions, and burst pressure.NOTE 1Socket-type CPVC plastic pipe fittings, Schedule 40, whichwere formerly included in this standard, are now covered by SpecificationF438.1.2 T

4、he products covered by this specification are intendedfor use with the distribution of pressurized liquids only, whichare chemically compatible with the piping materials. Due toinherent hazards associated with testing components and sys-tems with compressed air or other compressed gases, somemanufac

5、turers do not allow pneumatic testing of their products.Consult with specific product/component manufacturers fortheir specific testing procedures prior to pneumatic testing.NOTE 2Pressurized (compressed) air or other compressed gasescontain large amounts of stored energy which present serious safte

6、yhazards should a system fail for any reason.1.3 Fitting such as unions, flanges, special plastic-to-metaltransitions and appurtenances intended for use with PVCpiping are covered under specification F1970.1.4 The text of this specification references notes, footnotes,and appendixes which provide ex

7、planatory material. Thesenotes and footnotes (excluding those in tables and figures) shallnot be considered as requirements of the specification.1.5 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are p

8、rovided for information onlyand are not considered standard.1.6 The following safety hazards caveat pertains only tothe test method portion, Section 7, of this specification. Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility

9、 of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2. Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD1599 Test Method for Resistance to Short-Time Hydrau

10、licPressure of Plastic Pipe, Tubing, and FittingsD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD1784 Specification for Rigid Poly(Vinyl Chloride) (PVC)Compounds and Chlorinated Poly(Vinyl Chloride)(CPVC) CompoundsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and F

11、ittingsD2749 Symbols for Dimensions of Plastic Pipe FittingsF412 Terminology Relating to Plastic Piping SystemsF438 Specification for Socket-Type Chlorinated Poly(VinylChloride) (CPVC) Plastic Pipe Fittings, Schedule 40F1498 Specification for Taper Pipe Threads 60 for Thermo-plastic Pipe and Fitting

12、sF1970 Specification for Special Engineered Fittings, Appur-tenances or Valves for use in Poly (Vinyl Chloride) (PVC)or Chlorinated Poly (Vinyl Chloride) (CPVC) Systems2.2 NSF Standards:Standard No. 14 for Plastic Piping Components and RelatedMaterials3Standard No. 61 for Drinking Water Systems Comp

13、onentsHealth Effects33. Terminology3.1 GeneralDefinitions are in accordance with Terminol-ogy F412, and abbreviations are in accordance with Terminol-ogy D1600, unless otherwise indicated. The abbreviation forpoly(vinyl chloride) plastic is PVC.1This specification is under the jurisdiction of ASTM C

14、ommittee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.Current edition approved Aug. 1, 2013. Published September 2013. Originallyapproved in 1965. Last previous edition approved in 2006 as D2466 06. DOI:10.1520/D2466-13.2For referenced ASTM standar

15、ds, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd., AnnArbor, MI 4811

16、3-0140.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States14. Classification4.1 GeneralThis specification covers Schedule 40 PVCpipe fittings, made from four PVC plastic com

17、pounds andintended for use with Iron Pipe Size (IPS) outside-diameterplastic pipe.4.1.1 Fittings covered by this specification are normallymolded. In-line fittings, such as couplings, bushings, caps,nipples, etc., shall be molded or machined from extruded stock.4.1.2 Fittings fabricated by welding a

18、re not included in thisspecification.5. Materials5.1 This specification covers PVC pipe fittings made fromfive PVC plastics as classified in Specification D1784. Theseare PVC 12454, 12454, 13354, 11443, and 14333.5.2 CompoundThe PVC plastic compound shall meet therequirements of PVC 12454, 12454, 11

19、443, or 14333, asdescribed in Specification D1784.NOTE 3Mechanical strength, heat resistance, flammability, andchemical resistance requirements are covered in Specification D1784.5.3 Rework MaterialThe manufacturers shall use onlytheir own clean rework fitting material and the fittings pro-duced sha

20、ll meet all the requirements of this specification.6. Requirements6.1 Dimensions and Tolerances:6.1.1 Fitting sockets inside diameters (waterways), mini-mum wall thicknesses, and dimensions shall be as shown inTable 1, Table 2, and Table 3 when measured in accordancewith Test Method D2122.6.1.2 When

21、 multistep reducer bushings are cored out, theinner socket shall be reinforced from the outer wall by aminimum of three ribs extending from the top of the innersocket to the deepest extremity of the coring. The transitionfromDtoDJ(Table 3) shall be straight, tapered as shown, orradiused. A positive

22、taper in the same direction of the taper inthe socket on the outside diameter of the bushing is optional(See XA/XB in Table 3).Any point measured along the outsidediameter of the bushing (between points XA and XB) shall notfall below minimum pipe OD.6.1.3 The minimum wall thickness of fittings shall

23、 be 125 %of the minimum wall thickness of the corresponding size ofSchedule 40 pipe for which they are designed to be used,except that for the socket, the wall thickness shall be at leastequal to the minimum wall thickness of the corresponding sizeof Schedule 40 pipe. For any threaded fitting the mi

24、nimum wallthickness of the threaded portion shall be at least equal to thethickness of material under the thread root of threaded Sched-ule 80 pipe of the same size.6.1.4 The minimum inside diameter of the fittings shall benot less than the minimum specified inside diameter of thecorresponding size

25、of Schedule 40 pipe. Any fitting having amale thread shall have an internal diameter not larger thanSchedule 80 pipe of the same size.6.1.5 Minimum dimensions have zero negative tolerance.Tolerances on other dimensions are shown in Table 1 and Table3.6.2 ThreadsFor all fittings having taper pipe thr

26、eads,threads shall conform to Specification F1498 and be gaged inaccordance with 8.4.6.3 Burst Pressure:6.3.1 The minimum burst strength of the fittings shall be notless than that calculated for the size and wall thickness of thepipe with which it is to be used, when calculated from thefollowing equ

27、ation:S 5 PDO2 t!/2t (1)where:S = hoop stress, psi (or MPa),P = internal pressure, psi (or MPa),DO= average outside diameter, in. (or mm), andt = minimum wall thickness, in. (or mm).Fittings tested in accordance with 8.5 shall withstand theminimum burst pressure shown in Table 4.6.3.2 Pressures show

28、n are minimum burst pressures and donot imply rated working pressures. The burst pressure shall beused only as an indication of quality.7. Workmanship, Finish, and Appearance7.1 The fittings shall be homogeneous throughout and freeof cracks, holes, foreign inclusions, or other defects. Thefittings s

29、hall be as uniform as commercially practicable incolor, opacity, density, and other physical properties.8. Test Methods8.1 ConditioningCondition the test specimens at 73 63.6F (23 6 2C) and 50 6 5 % relative humidity for not lessthan 40 h prior to test in accordance with Procedure A ofPractice D618,

30、 for those tests where conditioning is required.8.2 Test ConditionsConduct tests in the Standard Labora-tory Atmosphere of 73 6 3.6F (23 6 2C) and 50 6 5%relative humidity, unless otherwise specified in the test meth-ods or in this specification.8.3 SamplingA sufficient quantity of fittings as agree

31、dupon between the seller and the purchaser shall be selected atrandom from each lot or shipment and tested to determine thatthe basic design is in conformance with this specification.NOTE 4For individual orders or specifications, only those tests andnumbers of tests specifically agreed upon between

32、the purchaser and theseller need be conducted.8.4 ThreadsAll taper pipe threads shall be gaged inaccordance with Specification F1498.8.5 Burst PressureDetermine the minimum burst pressurein accordance with Test Method D1599. The pressure shall beapplied at a uniform rate such that the minimum allowa

33、bleburst pressure is attained in 60 or 70 s.NOTE 5The time-to-failure may exceed 70 s.8.5.1 ApparatusFittings shall be tested while held in atest jig constructed in such a manner as to seal the socket bymeans of O-rings, or gaskets but not to reinforce or support thefittings, except where contact is

34、 necessary because of the shapeof the fitting to keep the fitting in the test jig. Such contact shallbe held to the minimum. The socket plug portion of the testD2466 132fixture must extend one third to two thirds of the socket depth.Failure of any part of the test apparatus does not constitutefailur

35、e of the fittings.9. Retest and Rejection9.1 If the results of any test(s) do not meet the requirementsof this specification, the tests(s) shall be conducted again onlyby agreement between the purchaser and seller. Under suchagreement, minimum requirements shall not be lowered,changed, or modified,

36、nor shall specification limits be changed.If upon retest, failure occurs, the quantity of product repre-sented by the test(s) does not meet the requirements of thisspecification.10. Marking10.1 Fittings shall be marked with the following:10.1.1 Manufacturers name or trademark,10.1.2 Material designa

37、tion PVC I for PVC 12454-B, PVC12 for PVC 12454-C, PVC 13 for PVC 13354-C and 11443-B,and PVC II for PVC 14333-D,TABLE 1 Tapered Sockets for PVC Pipe Fittings, Schedule 40, in.ANominalPipeSizeASocket Entrance DiameterBSocket Bottom Diameter CBSocketLength,minDCInsideDiameter,minWall Thickness, minMi

38、nOutsideDiameterof Hub, MEntrance, minDiameterToleranceonDiameterMaxOut-of-RoundDiameterToleranceonDiameterMaxOut-of-RoundE F EW EX, EZ18 0.417 0.004 0.016(0.41)0.401 0.004 0.016(0.41)0.500 0.225 0.068 0.085 0.52616416414 0.552 0.004 0.016(0.41)0.536 0.004 0.016(0.41)0.500 0.320 0.088 0.110 0.672164

39、16438 0.687 0.004 0.016(0.41)0.671 0.004 0.016(0.41)0.594 0.449 0.091 0.114 0.82113213212 0.848 0.004 0.016(0.41)0.836 0.004 0.016(0.41)0.688 0.578 0.109 0.136 0.99813213234 1.058 0.004 0.020(0.51)1.046 0.004 0.020(0.51)0.719 0.740 0.113 0.141 1.2211321321 1.325 0.005 0.020(0.51)1.310 0.005 0.020(0.

40、51)0.875 0.990 0.133 0.166 1.504116116114 1.670 0.005 0.024(0.61)1.655 0.005 0.024(0.61)0.938 1.335 0.140 0.175 1.871116116112 1.912 0.006 0.024(0.61)1.894 0.006 0.024(0.61)1.094 1.564 0.145 0.181 2.1271161162 2.387 0.006 0.024(0.61)2.369 0.006 0.024(0.61)1.156 2.021 0.154 0.193 2.634116116212 2.889

41、 0.007 0.030(0.76)2.868 0.007 0.030(0.76)1.750 2.414 0.203 0.254 3.170332183 3.516 0.008 0.030(0.76)3.492 0.008 0.030(0.76)1.875 3.008 0.216 0.270 3.84133218312 4.016 0.008 0.030(0.76)3.992 0.008 0.030(0.76)2.000 3.486 0.226 0.283 4.374332184 4.518 0.009 0.030(0.76)4.491 0.009 0.030(0.76)2.000 3.961

42、 0.237 0.296 4.907332185 5.583 0.010 0.060(1.52)5.553 0.010 0.060(1.52)3.000 4.975 0.258 0.323 6.039332186 6.647 0.011 0.060(1.52)6.614 0.011 0.060(1.52)3.000 5.986 0.280 0.350 7.203183168 8.655 0.015 0.090(2.29)8.610 0.015 0.090(2.29)4.000 7.888 0.322 0.403 9.3201831610 10.780 0.015 0.100(3.05)10.7

43、35 0.015 0.100(3.05)5.000 9.917 0.365 0.456 11.6141831612 12.780 0.015 0.120(3.81)12.735 0.015 0.120(3.81)6.000 11.825 0.406 0.508 13.78618316AThe sketches and designs of fittings are illustrative only.BSocket depth, measured from socket entrance face to socket bottom face.CSee 6.1.4.D2466 13310.1.3

44、 Fittings intended for the transport of potable watershall include the seal or mark of the laboratory making theevaluation for this purpose.10.1.4 Size, and10.1.5 This designation number: D2466.10.2 Where the size of the fitting does not allow completemarking, omit identification marking in the foll

45、owing se-quence: size, material designation, manufacturers name ortrademark.10.3 Markings or symbols shall be molded, hot-stamped, orapplied to fittings by any other suitable method, such asprinting.10.4 Where recessed marking is used, care shall be taken tosee that in no case marking causes cracks

46、or reduces the wallthickness below the minimum specified.11. Quality Assurance11.1 When the product is marked with this designation,D2466, the manufacturer affirms that the product wasmanufactured, inspected, sampled, and tested in accordancewith this specification and has been found to meet therequ

47、irements of this specification.12. Keywords12.1 fittings; pressure; PVC; Sch 40; sockets; threadsTABLE 2 Minimum Dimension from Center to End of Sockets(Laying Length) for Couplings, Tees, 90 and 45 Elbows, PVCSocket-Type Pipe Fittings, Schedule 40, in.ANominalPipe SizeG,min J,min N,min1814181161451

48、6532116383831633212121433234916516332111165163321147838332112 1716332211458332212 112111631631131634316312 218 131642516 131653383166312 134148412 21410 51316 29161412 61516 311614AThe sketches and designs of fittings are illustrative only.D2466 134TABLE 3 Dimensions of Reducer Bushings, PVC Socket-

49、Type Pipe Fittings, Schedule 40,Ain. (mm)Nominal Size Outside DiameterXATolerance onOutside DiameterOutside DiameterXBTolerance onOutside DiameterMaximum Out-of-Roundness(max, minus min.)14 by18 0.540 (13.72) +0.007 0.004 (0.18 0.10) 0.540 (13.72) 0.004 (0.10) 0.016 (0.41)38 by14,18 0.675 (17.41) +0.007 0.004 (0.18 0.10) 0.675 (17.41) 0.004 (0.10) 0.016 (0.41)12 by38,14 0.840 (21.34) +0.007 0.004