ASTM D3409-1993(2002)e1 Standard Test Method for Adhesion of Asphalt-Roof Cement to Damp Wet or Underwater Surfaces《沥青屋顶胶粘剂对潮湿表面、湿表面和水下表面粘着性的试验方法》.pdf

1、Designation: D 3409 93 (Reapproved 2002)e1Standard Test Method forAdhesion of Asphalt-Roof Cement to Damp, Wet, orUnderwater Surfaces1This standard is issued under the fixed designation D 3409; the number immediately following the designation indicates the year oforiginal adoption or, in the case of

2、 revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.e1NOTEEditorially switched from inch/pound dominant to SI dominant in April 2002.1. Scope1.1 This test met

3、hod covers the determination of the adhe-sion of asphalt roofing cements to damp, wet, or underwatersurfaces.1.2 The values in SI units are to be regarded as standard.The values in parentheses are for information only.1.3 This standard does not purport to address all of thesafety concerns, if any, a

4、ssociated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Summary of Test Method2.1 A metal lid is covered with a coating of asphalt roofingcement and i

5、mmersed in water. A similar metal lid which hasbeen flamed and wet with water is pressed on the asphalticsurface. The degree of adhesion is evaluated by estimating thepercentage of area covered by the cement on the water-wetflamed metal lid.3. Significance and Use3.1 This test method offers a means

6、of evaluating theadhesive properties of asphalt roofing cements used to repairroofs under adverse conditions. Weathered roof surfaces areeasily coated with asphalt roofing cements when they are dry,however when wet or during a rain, asphalt roofing cementsmay not adhere readily to water-wet surfaces

7、 such as metalflashings or asphalt roll roofing. The flamed metal lids used inthis test method simulate weathered roof surfaces.4. Apparatus4.1 Metal Lids2Slip-on covers supplied with 89-mL (3-fluid oz) capacity seamless metal containers, approximately 55mm in diameter and with a raised rim 1 mm hig

8、h and 3 mmwide.4.2 Water BathA bath with a flat bottom surface having acapacity of at least 1 L (1 qt) which can be filled with tap waterto a minimum depth of 51 mm (2 in.) and maintained at 20 63C (68 6 5F).5. Sampling5.1 Stir the sample thoroughly to ensure homogeneity be-fore removing a portion f

9、or testing.5.2 If the size of the sample is 4 L (1 gal) or over, a portionmay be removed and stored in a 1-L (1-qt) triple-seal, friction-top can.6. Procedure6.1 Spread5gofthecement on the top surface of each ofthree metal lids and place them in the water bath.6.2 Flame three other metal lids in an

10、open gas flame untileach entire lid has an oxidized blue-gray surface and placethem in the water bath after they have cooled to roomtemperature.6.3 After 5 min, place a flamed lid on top of each cement-covered lid, and press only on the rim of the flamed lid for 1min or until the flow of the cement

11、stops.NOTE 1Covers that have a raised rim (1 mm) on the top surface areintended for this test. When the two lids are pressed together, approxi-mately4gofthe5-gsample will be contained between the surfaces. If lidswith raised rims are not available, smooth lids may be used except thatcare should be e

12、xercised in pressing the lids together to prevent squeezingout all of the sample.6.4 Remove each set of lids from the water bath and scrapeoff the excess cement around the edges with a spatula or knife.6.5 Separate the lids without twisting and estimate thepercentage of area covered by the cement on

13、 each of the flamedlids.7. Report7.1 Report the average of the three estimates on coverage ofthe cement on the flamed lids as the adhesion, in percent, at20C (68F).1This test method is under the jurisdiction of ASTM Committee D08 onRoofing, Waterproofing, and Bituminous Materials and is the direct r

14、esponsibility ofSubcommittee D08.05 on Solvent-Bearing Bituminous Compounds for Roofing andWaterproofing.Current edition approved Oct. 15, 1993. Published December 1993. Originallypublished as D 3409 75. Last previous edition D 3409 81 (1987).2Deep Style 22 Seamless Cans, available from Ellisco Inc.

15、, Myers Div., 6850River Rd., Pennsauken, NJ 08110, have been found satisfactory for this purpose.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.NOTE 2There may be a need for testing at lower temperatures.Committee D08 would welcome

16、data supporting suitable modifications.8. Precision8.1 The precision of this test method has not yet beendetermined.9. Keywords9.1 adhesion; asphalt cement; wet surfaceASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin t

17、his standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must

18、be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of there

19、sponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D 34092