ImageVerifierCode 换一换
格式:PDF , 页数:4 ,大小:74.53KB ,
资源ID:515064      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-515064.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM D3595-2002 Standard Specification for Polychlorotrifluoroethylene (PCTFE) Extruded Plastic Sheet and Film《聚三氟氯乙烯挤压塑料薄板及薄膜标准规范》.pdf)为本站会员(testyield361)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

ASTM D3595-2002 Standard Specification for Polychlorotrifluoroethylene (PCTFE) Extruded Plastic Sheet and Film《聚三氟氯乙烯挤压塑料薄板及薄膜标准规范》.pdf

1、Designation: D 3595 02Standard Specification forPolychlorotrifluoroethylene (PCTFE) Extruded Plastic Sheetand Film1This standard is issued under the fixed designation D 3595; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year

2、 of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope*1.1 This specification covers extru

3、ded sheet and film inthicknesses from 0.015 to 0.25 mm (0.0006 to 0.01 in.).1.2 The values stated in SI units shall be regarded as thestandard.1.3 The following precautionary statement pertains only tothe test methods portion, Section 9 of this specification: Thisstandard does not purport to address

4、 all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.NOTE 1There is no ISO equivalent specification to this specifi

5、cation.22. Referenced Documents2.1 ASTM Standards:D 374 Test Methods for Thickness of Solid Electrical Insu-lation3D 618 Practice for Conditioning Plastics for Testing4D 882 Test Methods for Tensile Properties of Thin PlasticSheeting4D 883 Terminology Relating to Plastics4D 1204 Test Method for Line

6、ar Dimensional Changes ofNonrigid Thermoplastic Sheeting or Film at ElevatedTemperature4D 1430 Classification System for Polychlorotrifluoroethyl-ene (PCTFE) Plastics4D 1600 Terminology for Abbreviated Terms Relating toPlastics4D 3892 Practice for Packaging/Packing of Plastics5F 1249 Test Method for

7、 Water Vapor Transmission RateThrough Plastic Film and Sheeting Using a ModulatedInfrared Sensor6IEEE/ASTM SI 10 Standard for Use of the InternationalSystem of Units (SI): The Modern Metric System73. Terminology3.1 Definitions of terms used in this specification shall be inaccordance with Terminolog

8、y D 883.3.2 lot, none production run or a uniform blend of two ormore production runs.3.3 Abbreviations are in accordance with TerminologyD 1600. PCTFE is the abbreviation for polychlorotrifluoroet-hylene.4. Classification4.1 This specification covers four types of polychlorotrif-luoroethylene sheet

9、 and film:84.1.1 Type ITransparent film, with high and low moisturevapor transmission rate.4.1.2 Type IIDimensionally stable transparent sheet andfilm with low moisture vapor transmission rate.4.1.3 Type IIIDimensionally stable transparent film withvery low moisture vapor transmission rate.4.1.4 Typ

10、e IVLow crystalline transparent film with highductility and extremely low moisture vapor transmission.4.2 A one-line system may be used to specify materialscovered by this specification. The system uses predefined cellsto refer to specific aspects of this specification, as illustratedbelow.1This spe

11、cification is under the jurisdiction of ASTM Committee D20 onPlastics and is the direct responsibility of Subcommittee D20.15 on ThermoplasticMaterials.Current edition approved March 10, 2002. Published May 2002. Originallypublished as D 3595 77. Last previous edition D 3595 97.2As defined in IEEE/A

12、STM SI 10.3Annual Book of ASTM Standards, Vol 10.01.4Annual Book of ASTM Standards, Vol 08.01.5Annual Book of ASTM Standards, Vol 08.02.6Annual Book of ASTM Standards, Vol 15.09.7Available from ASTM International, 100 Barr Harbor Drive, West Consho-hocken, PA 194282959.8The basic polymer used to mak

13、e these types of polymer does not correspond tothe types given in Specification D 1430.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.SpecificationStandard NumberBloc

14、k:Type:Grade:Class:SpecialNotes:- - - - -Example: Specification D 3595 02, I 6 CFor this example, the line callout would be SpecificationD 3595 02, I6C, and would specify a coagulated dispersionform of polytetrafluoro-ethylene that has all of the propertieslisted for that Type, Grade, and Class in t

15、he appropriatespecified properties, tables, or both, in the specification iden-tified. A comma is used as the separator between the StandardNumber and the Type. Separators are not needed between theType, Grade, and Class.9Provision for Special Notes isincluded so that other information can be provid

16、ed whenrequired. An example would be in Specification D 3295 81awhere dimensions and tolerances are specified for each AWGsize within Type and Class. When Special Notes are used, theyshould be preceded by a comma.5. Requirements5.1 The sheet and film shall be manufactured from poly-chlorotrifluoroet

17、hylene (PCTFE) plastics that consist of at least90 % chlorotrifluoroethylene. The remaining 10 % may in-clude chemical modifications, such as co-monomers, but notcolorants, fillers, plasticizers, or mechanical blends of otherresins.5.2 The length, width, roll core diameter, and maximumnumber of spli

18、ces permitted shall be as agreed upon betweenthe purchaser and the seller. The tolerance for roll width shallbe 3 % mm (18 in.). The tolerance for roll length shall be 610 % of the specified length.5.3 Thickness tolerances shall be as specified in Table 1.5.4 The sheet and film shall conform to the

19、property valuesspecified in Table 2, Table 3, and Table 4.5.5 The material shall be essentially free from contamina-tion, wrinkles, holes, scratches, and other imperfections unlessotherwise agreed upon between the purchaser and the seller.6. Sampling6.1 Sampling shall be statistically adequate to sa

20、tisfy therequirements of 10.4.7. Number of Tests7.1 One set of test specimens as prescribed in Section 8shall be considered sufficient for testing each batch. Theaverage result of the specimens tested shall conform to therequirements of this specification.8. Specimen Preparation8.1 ConditioningFor t

21、hose tests where conditioning isrequired, condition the test specimens in accordance withProcedureAof Practice D 618 for a period of at least 24 h priorto test.8.2 Test ConditionsUnless otherwise specified, conducttests at the Standard Laboratory Temperature of 23 6 2C (70to 77F) and at 50 6 5 % rel

22、ative humidity.8.3 Preparation of SpecimensTake test specimens acrossthe width of the roll.9. Test Methods9.1 ThicknessMeasure the thickness of the sheet of film inaccordance with Test Methods D 374, MethodAor C. Measurethe sample across the web width at 25-mm (1-in.) increments.All readings shall b

23、e within the specified tolerances. Abnormalreadings may occasionally result from spot imperfections.Discard such readings and take new readings in the same area(excluding the defect).9.2 Tensile Strength and ElongationDetermine tensilestrength and elongation of the sheet or film in accordance with9S

24、ee the ASTM Form and Style Manual. Available from ASTM Headquarters.TABLE 1 Thickness ToleranceThicknessTolerance, % Type Availabilitymm in.0.015 0.0006 620 IV0.019 0.00075 620 III0.023 0.0009 620 IV0.038 0.0015 620 I,0.051 0.0002 615 I, II, III, IV0.076 0.0003 615 II0.127 0.0005 615 II0.19 0.0075 6

25、10 II0.20 0.0078 610 III0.25 0.010 610 IITABLE 2 Tensile Strength and ElongationThickness, mm (in.) TypeTensile Strength, minElongation,min, %psi MPa0.019 to 0.038 I, II, III 2800 19.32 50(0.00075 to 0.0015)0.051 to 0.25 I, II, III 3100 21.40 50(0.020 to 0.01)0.016 to 0.051 IV 4500 31.0 70(0.0006 to

26、 0.002)TABLE 3 Dimensional StabilityThickness, mm (in.) Type Shrinkage,Amax,%0.038 to 0.051 I 6170.0015 to 0.0020.019 to 0.051 II, III 630.00075 to 0.0020.051 to 0.25 III 630.002 to 0.25 II 650.016 to 0.051 IV 6150.0006 to 0.002)APositive sign means increase in length.TABLE 4 Moisture Vapor Transmis

27、sion RateThicknessTypeMoisture VaporTransmission Rate,max, g/m23 24 hmm in.0.038 0.0015 I 0.610.019 0.00075 III 0.680.051 0.002 II 0.570.0051 0.002 III 0.310.016 0.0006 IV 0.420.051 0.002 IV 0.12D3595022Test Methods D 882, Method A. The specimen size shall be 25by 127 mm (1 by 5 in.). Elongation rat

28、e shall be 508 mm (20in.)/min. Separation between jaws shall be 51 mm (2 in.).Edges of the specimen shall be parallel within 2 % of thewidth.9.3 Dimensional StabilityTest dimensional stability of thesheet or film in accordance with Test Method D 1204 afterexposure to 149C (300F) for 10 min.9.4 Moist

29、ure Vapor Transmission RateMeasure the mois-ture vapor transmission rate in accordance with Test MethodF 1249 at 100 % relative humidity at 38C (100F).10. Inspection and Certification10.1 Inspection and certification of the material suppliedwith reference to a specification based on this specificati

30、onshall be for conformance to the requirements specified herein.10.2 Lot-acceptance shall be the basis on which acceptanceor rejection of the lot is made. The lot acceptance inspectionshall consist of thickness measurement.10.3 Periodic check inspection with reference to this speci-fication shall co

31、nsist of the test for all requirements of thematerial in accordance with this specification.10.4 Certification shall be that the material was manufac-tured by a process in statistical control, sampled, tested, andinspected in accordance with this specification, and that theaverage values for the lot

32、 meet the requirements of thisspecification.10.5 A report of test results shall be furnished when re-quested. The report shall consist of results of the lot-acceptanceinspection for the shipment and the results of the most recentperiodic-check inspection.11. Packaging and Package Marking11.1 Packagi

33、ngThe material shall be packaged in stan-dard commercial containers so constructed as to ensure accep-tance by common or other carriers for safe transportation at thelowest rate to the point of delivery, unless otherwise specifiedin the contract or order.11.2 MarkingShipping containers shall be mark

34、ed withthe name of the material, type, size, and quantity containedtherein. Each roll of tape shall be marked to designate type,grade, and lot number. The marking will be in the core and onthe pallet.11.3 All packing, packaging, and marking provisions ofPractice D 3892 shall apply to this specificat

35、ion.12. Keywords12.1 chlorofluorocarbon plastics; copolymer; extrudedPCTFE; fluorocarbon polymer; fluoropolymers; homopolymer;PCTFE; PCTFE film; PCTFE sheet;polychlorotrifluoroethyleneSUMMARY OF CHANGESThis section identifies the location of selected changes to this test method. For the convenience

36、of the user,Committee D20 has highlighted those changes that may impact the use of this test method. This section may alsoinclude descriptions of the changes, or reasons for the changes, or both.D 3595 02:(1) Added IEEE/ASTM SI 10.(2) Deleted all reference to Practice D 1898.(3) Added definition of

37、lot to 3.1.(4) Editorially corrected 4.1.(5) Editorially corrected 4.2.(6) Revised 6.1 and deleted 6.2 and 6.3.(7) Revised Section 11.(8) Deleted section on Rejection and Rehearing.D 3595 97:(1) Changed extruded sheet and film thicknesses in 1.1.(2) Added Note 1.(3) Added Test Method F 1249 to 2.1.(

38、4) Added revisions to 4.1.1, 4.1.3, and 4.1.4 .(5) Table 1 reflects changes in thicknesses for standard prod-ucts.(6) The sheet and film shall conform to the property valuesspecified in Table 2, Table 3, and Table 4. These tables havebeen changed to reflect the new thickness and addition of TypeIV m

39、aterial.(7) Revised 8.3.(8) Changed dimensional stability to 10 min in 9.3.(9) Revised 9.4 and deleted the section on the old MVTRmethod, including Footnote 7.(10) Revised 12.2.2.(11) Added homopolymer and copolymer to Keywords.D3595023ASTM International takes no position respecting the validity of

40、any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to r

41、evision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Yo

42、ur comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is cop

43、yrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D3595024

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1