1、Designation: D4465 05 (Reapproved 2015)Standard Performance Specification forZippers for Dungarees, Jeans and Work Trousers1This standard is issued under the fixed designation D4465; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision,
2、the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This performance specification covers zippers to be usedas fly closures in dungarees, jeans and work trous
3、ers madefrom heavy denim or other durable fabric, approximately 475g/m2(14 oz/yd2).1.2 Zippers covered by this specification may be satisfac-tory for lighter weight denim and other fabrics.1.2.1 When lighter weight material is being used, consider-ation should be given to the zipper size and slider
4、type becauseof their effect on the appearance of the zipper installation area.1.3 The values stated in SI units are to be regarded as thestandard. The values in parentheses are for information only.2. Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD2050 Terminology Rela
5、ting to Fasteners and ClosuresUsed with TextilesD2057 Test Method for Colorfastness of Zippers to Laun-deringD2060 Test Methods for Measuring Zipper DimensionsD2061 Test Methods for Strength Tests for ZippersD2062 Test Methods for Operability of ZippersD2905 Practice for Statements on Number of Spec
6、imens forTextiles (Withdrawn 2008)33. Terminology3.1 Definitions:3.1.1 denim, na durable woven twill fabric, usually of allcotton or a blend of cotton and man-made fibers, made from avariety of yarn numbers, and in various fabric weights, colors,designs, and finishes.3.1.1.1 DiscussionTraditionally,
7、 denim is made with in-digo blue dyed cotton warp and undyed or tinted filling. Denimfabrics are used for many types of garments including workclothes, sportswear, dresswear, and home furnishings.3.2 Definitions of Terms Specific to This Standard:3.2.1 jeans, na style of trousers made of a twill fab
8、ric usedas sportswear and work clothing.3.2.2 dungaree, ntrousers made from denim and designedfor general heavy work wear.3.2.3 trouser, na garment that closes at the waist andcovers the lower body to the crotch and each leg from the waistto the ankle.3.3 For other textile terminology used in this s
9、pecification,refer to Terminology D123. For definitions of zipper termsused in this specification, refer to Terminology D2050.4. Specification Requirements4.1 The properties of zippers for dungarees, jeans and worktrousers shall conform to the specification requirements inTable 1.5. Significance and
10、 Use5.1 This specification serves as a guide for the purchase ofzippers to be used for dungarees, jeans or work trousers.5.2 Upon agreement between the purchaser and the supplier,zippers intended for this end-use should meet all of therequirements listed in Table 1 of this specification.5.3 It is re
11、cognized that for purposes of fashion or aestheticsthe ultimate consumer may find acceptable dungarees, jeans orwork trousers, having zippers that do not conform to all of therequirements in Table 1. Therefore, one or more of therequirements listed in Table 1 may be modified by agreementbetween the
12、purchaser and the supplier.5.3.1 In such cases, and references to this specification shallspecify that: This zipper meets Performance SpecificationD4465 except for the following characteristic(s).5.4 Where no prepurchase agreement has been reachedbetween the purchaser and the supplier, and in case o
13、fcontroversy, the requirements listed in Table 1 are intended tobe used as a guide only. As noted in 5.3 ultimate consumerdemands dictate varying performance parameters for anyparticular style of zipper.1This performance specification is under the jurisdiction of ASTM CommitteeD13 on Textiles and is
14、 the direct responsibility of Subcommittee D13.54 onSubassemblies. This performance specification was developed in cooperation withthe Slide Fastener Association, Inc.Current edition approved Feb. 1, 2015. Published April 2015. Originallyapproved in 1985. Last previous edition approved in 2010 as D4
15、465 05(2010).DOI: 10.1520/D4465-05R15.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The last approved vers
16、ion of this historical standard is referenced onwww.astm.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States15.5 The uses and significance of particular properties andtest methods are discussed in the appropriate sections of thespecif
17、ied test methods.6. Sampling6.1 Description of LotsUnless there is prior agreement,consider as a lot for acceptance testing all material of a singleitem received as a single shipment.6.2 Lot Samples and Laboratory SamplesFor acceptancetesting, take lot samples and laboratory samples as directed inea
18、ch of the applicable test methods.6.3 Test SpecimensTake the number of specimens directedin each of the applicable test methods. Take the specimens, andperform the tests on zippers as received by the garmentmanufacturer or on zippers removed from unused garments.6.3.1 If the method does not specify
19、the number of speci-mens and there has been no prior agreement, use the proce-dures in Practice D2905 to determine the number of specimensper unit in the laboratory sample when using a reliable estimateof the variability of individual observations on similar materi-als in the users laboratory under
20、conditions of single-operatorprecision. The number of specimens per unit in the laboratorysample shall be such that the user may expect at the 95 %probability level that each test result is not more than 5 % ofthe average above or below the true average for the unit in thelaboratory sample.7. Test M
21、ethods7.1 Element Pull-OffDetermine the resistance of the ele-ment to being pulled from the tape as directed in Test MethodsD2061.7.2 Element SlippageDetermine the element resistance toslippage as directed in Test Methods D2061.7.3 Crosswise StrengthDetermine the crosswise strengthof the chain as di
22、rected in Test Methods D2061.7.4 Bottom Stop Holding-Stringer SeparationDeterminethe bottom stop holding-stringer separation strength as directedin Test Methods D2061.7.5 Top Stop HoldingDetermine the top stop holdingstrength as directed in Test Methods D2061.7.6 Slider Lock HoldingDetermine the hol
23、ding strength ofthe slider lock as directed in Test Methods D2061.7.7 Slider Deflection and Recovery-PullDetermine thedeflection and recovery for the slider as directed in TestMethods D2061.7.8 Resistance to Pull-Off of Slider PullDetermine theresistance of the slider pull to pull-off as directed in
24、 TestMethods D2061.7.9 OperabilityDetermine the ease of slider operation onthe chain as directed in Test Methods D2062.7.10 Longitudinal Dimensional Change-LaunderingDetermine the longitudinal dimensional change of the zipper asmeasured on the tape after laundering as directed in TestMethods D2060.7
25、.11 Colorfastness to LaunderingDetermine the colorfast-ness of the textile portion of the zipper to laundering asdirected in Test Method D2057.TABLE 1 Specification Requirements for Zippers for Dungaree, Jeans and Work TrousersCharacteristics Requirement SectionElement pull-off 62 N (14 lbf), min 7.
26、1Element slippage 44 N (10 lbf), min 7.2Crosswise strength 578 N (130 lbf), min 7.3Bottom stop holdingstringer separation 111 N (25 lbf), min 7.4Top stop holding 111 N (25 lbf), min 7.5Slider lock holdingPositive lock 111 N (25 lbf), min 7.6Ratchet lock 31N(7lbf),min 7.6Slider deflection and recover
27、yPull Method:Deflection 0.254 mm (0.010 in.), max 7.7Permanent set 0.127 mm (0.005 in.), maxResistance to pull-off of slider pull 111 N (25 lbf), min 7.8Operability 6.7 N (1.5 lbf), max 7.9Longitudinal Dimensional ChangeLaundering:Normal shrinkage level 3.5 % max 7.10Low shrinkage level 1.5 % max 7.
28、10Colorfastness to launderingColor change 3.5 min 7.11Staining 3.5 min 7.11D4465 05 (2015)2ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination
29、 of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdraw
30、n. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your co
31、mments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single o
32、r multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 05 (2015)3
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1