ASTM D4709-2007(2012) Standard Specification for Methyl Acrylate《丙烯酸甲酯标准规格》.pdf

1、Designation: D4709 07 (Reapproved 2012)Standard Specification forMethyl Acrylate1This standard is issued under the fixed designation D4709; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in pare

2、ntheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers methyl acrylate (99 % grade)for use in paint, varnish, lacquer, and related products.1.2 The following applies to all spec

3、ified limits in thisstandard; for purposes of determining conformance with thisstandard, an observed value or a calculated value shall berounded off “to the nearest unit” in the last right-hand digitused in expressing the specification limit, in accordance withthe rounding-off method of Practice E29

4、.1.3 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish app

5、ro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use. For specific hazardinformation see Section 4.1.5 For specific hazard information and guidance, see thesuppliers Material Safety Data Sheet for materials listed in thisspecification.2. Refer

6、enced Documents2.1 ASTM Standards:2D1209 Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)D1364 Test Method for Water in Volatile Solvents (KarlFischer Reagent Titration Method)D1613 Test Method for Acidity in Volatile Solvents andChemical Intermediates Used in Paint, Varnish, Lacquer,a

7、nd Related ProductsD3125 Test Method for Monomethyl Ether of Hydroquinonein Colorless Monomeric Acrylate Esters and Acrylic AcidD3362 Test Method for Purity of Acrylate Esters by GasChromatography (Withdrawn 2011)3D5386 Test Method for Color of Liquids Using TristimulusColorimetryE29 Practice for Us

8、ing Significant Digits in Test Data toDetermine Conformance with SpecificationsE300 Practice for Sampling Industrial Chemicals2.2 U.S. Federal Specification:PPP-C-2020 Chemicals, Liquid, Dry, and Paste: Packagingof43. Properties3.1 Methyl acrylate shall conform to the following require-ments:Purity,

9、 wt %, min, as methyl acrylate 99.5Water, wt %, min 0.10Color, Pt-Co units, max (Note 1)in bulk shipments 10in drum shipments 20Acidity, (free acid acrylic acid), wt %, max 0.01Methyl ether of hydroquinone as agreed upon by the purchaserand the manufacturer_NOTE 1Instrumental Pt-Co color determined

10、by Test Method D5386has been shown to have no statistically significant difference from Pt-Cocolor determined by Test Method D1209. However, it is not knownwhether methyl acrylate was part of the sample set included in theinterlaboratory study.4. Hazards4.1 Methyl acrylate is a flammable liquid. Its

11、 vapors canform explosive mixtures with air and are particularly irritating.Store samples in amber bottles or protect from light by othermeans to aid in preventing polymerization. Keep samples awayfrom heat sources and chemicals that can cause free radicalpolymerization. Methyl acrylate can polymeri

12、ze violentlyevolving considerable heat. The inhibitor, methyl ether ofhydroquinone, requires oxygen to be active.5. Sampling5.1 The material shall be sampled in accordance withPractice E300 (see Section 4 on Hazards).1This specification is under the jurisdiction of ASTM Committee D01 on Paintand Rel

13、ated Coatings, Materials, and Applications and is the direct responsibility ofSubcommittee D01.35 on Solvents, Plasticizers, and Chemical Intermediates.Current edition approved July 1, 2012. Published September 2012. Originallyapproved in 1987. Last previous edition approved in 2007 as D4709 07. DOI

14、:10.1520/D4709-07R12.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The last approved version of this histo

15、rical standard is referenced onwww.astm.org.4Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:/www.dodssp.daps.mil.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Bar

16、r Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States16. Test Methods6.1 The properties enumerated in this specification shall bedetermined in accordance with the following ASTM testmethods:6.1.1 PurityTest Method D3362.6.1.2 WaterTest Method D1364.6.1.3 ColorTest Method D1209

17、 (see Note 1).6.1.4 AcidityDetermine the acidity in accordance withTest Method D1613, except multiply the results obtained “asacetic acid” by 76.06/60.05 or 1.2. This will convert the resultsobtained to “as acrylic acid.” The results obtained “as mg KOHper g of sample” are unaffected.6.1.5 Methyl Et

18、her of Hydroquinone ContentTest MethodD3125.7. Packaging and Package Marking7.1 Package size shall be agreed upon between the pur-chaser and the supplier.7.2 Packaging shall conform to applicable carrier rules andregulations or when specified shall conform to Fed. Spec.PPP-C-2020.8. Keywords8.1 acid

19、ity, alkalinity, or pH; color; methyl acrylate; puritySUMMARY OF CHANGESCommittee D01.35 has identified the location of selected changes to this standard since the last issue(D4709 - 02) that may impact the use of this standard. (Approved June 1, 2007.)(1) Added Test Method D5386 to list of Referenc

20、ed Docu-ments.(2) Added new Note 1 in 6.1.3.(3) Referenced new Note 1 in 6.1.3.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the vali

21、dity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comm

22、ents are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have

23、not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple c

24、opies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D4709 07 (2012)2