ASTM D4730-2002 Standard Specification for Flooding Compounds for Telecommunications Wire and Cable《电信电线和电缆用浸渍化合物的标准规范》.pdf

1、Designation: D 4730 02An American National StandardStandard Specification forFlooding Compounds for Telecommunications Wire andCable1This standard is issued under the fixed designation D 4730; the number immediately following the designation indicates the year oforiginal adoption or, in the case of

2、revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers a variety of compounds usedfor flooding the shields and armors of tel

3、ecommunicationswires and cables (both electrical and fiber optic) for thepurpose of preventing water and other undesirable fluids fromentering or migrating along or through the cable sheath. (Forrelated standards see Specifications D 4731 and D 4732.)2. Referenced Documents2.1 ASTM Standards:D 6 Tes

4、t Method for Loss on Heating of Oil and AsphalticCompounds2D 92 Test Method for Flash and Fire Points by ClevelandOpen Cup3D 482 Test Method for Ash from Petroleum Products3D 1321 Test Method for Needle Penetration of PetroleumWaxes3D 3236 Test Method for Apparent Viscosity of Hot MeltAdhesives and

5、Coating Materials4D 4565 Test Methods for Physical and Environmental Per-formance Properties of Insulations and Jackets for Tele-communications Wire and Cable5D 4568 Test Methods for Evaluating Compatibility Be-tween Cable Filling and Flooding Compounds and Poly-olefin Wire and Cable Materials5D 473

6、1 Specification for Hot-Application Filling Com-pounds for Telecommunications Wire and Cable5D 4732 Specification for Cool-Application Filling Com-pounds for Telecommunications Wire and Cable5E 28 Test Method for Softening Point of Resins Derivedfrom Naval Stores by Ring-and-Ball Apparatus63. Termin

7、ology3.1 Descriptions of Terms Specific to this Standard:3.1.1 flooding compoundsany of several materials used tofill the air spaces between the sheath elements of single andmulti-conductor insulated wires and cables or optical cables forthe purpose of excluding water and other undesirable fluids;es

8、pecially with regard to telecommunications wire and cable,including optical cable, intended for outside aerial or under-ground installations.3.1.2 producerthe primary manufacturer of the material.3.1.3 suppliersjobbers and distributors as distinct fromproducers.4. Ordering Information4.1 Orders for

9、material under this specification shall includethe following information:4.1.1 Quantity (mass or volume) of each item,4.1.2 Generic name of the material, such as cable floodingcompound,4.1.3 How furnished (drums or barrels, blocks, etc.),4.1.4 Certification, if required (see Section 11).4.1.5 This s

10、pecification designation, and4.1.6 Any special requirements, as listed in 8.2 and 9.2, thatapply.5. Materials and Manufacture5.1 The material and manufacturing methods used shall besuch that the resulting products will conform to the propertiesand characteristics prescribed in this specification.1Th

11、is specification is under the jurisdiction of ASTM Committee D09 onElectrical and Electronic Insulating Materials and is under the direct responsibilityof Subcommittee D09.18 on Solid Insulations, Non-Metallic Shieldings andCoverings for Electrical and Telecommunication Wires and Cables.Current edit

12、ion approved Sept. 10, 2002. Published October 2002. Originallypublished as D 473087. Last previous edition D 4730 93 (1998).2Annual Book of ASTM Standards, Vol 04.04.3Annual Book of ASTM Standards, Vol 05.01.4Annual Book of ASTM Standards, Vol 05.02.5Annual Book of ASTM Standards, Vol 10.02.6Annual

13、 Book of ASTM Standards, Vol 06.03.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.6. Compatibility with Other Materials6.1 It is the responsibility of the purchaser to ensure that theflooding compound ordered is suitable for the int

14、ended appli-cation and is compatible with any other components that maycome into contact with the flooding compound.6.2 The purchaser shall specify the materials that the com-pound must be compatible with when tested in accordance withTest Method D 4568.7. Chemical Composition7.1 The chemical compos

15、ition of these materials is notspecified. The material may be of any chemical compositionsuitable for the intended purpose and which meets the require-ments of this specification as hereinafter stated.7.2 Once established, the producer shall not change thecomposition of the compound in successive lo

16、ts of materialwithout prior approval of the purchaser.8. Physical Properties8.1 Flooding compound furnished under this specificationshall inhibit the corrosion of any metallic wire and cableelements with which it comes in contact, while serving as aradial and longitudinal barrier to moisture transmi

17、ssion. Con-tact of the flooding compound with any cable component shallnot cause degradation of performance of the cable component.The flooding compound shall display adhesive properties toprovide adhesion between metallic sheath elements and theouter jacket materials of wire and cable.8.2 Other Pro

18、perties:8.2.1 Other physical properties requirements such as Vis-cosity (for example, Test Method D 3236), Flash Point (forexample, Test Method D 92), Needle Penetration (for example,Test Method D 1321), Ring-and-Ball Softening Point (forexample, Test Method E 28), and Heat Stability/ViscosityChange

19、 (for example, Test Method D 3236), may be specified,if needed, and shall be as agreed-upon between the producerand the purchaser.8.3 The purchaser (individual cable manufacturer or other)shall specify any other expected requirements needed to ensurecompliance with such end-product requirements as c

20、old-bend,low-temperature flexibility, and the like (for example, TestMethods D 4565).9. General Requirements9.1 All flooding compounds manufactured in conformanceto this specification shall meet the following requirements:9.1.1 HomogeneityThe compound shall be homogeneousand uniformly mixed.9.1.2 Fo

21、reign MaterialThe compounds shall be free ofdirt, metallic particles, and other foreign matter.9.2 Other Properties:9.2.1 Other raw material requirements such as Volatility (forexample, Test Method D 6), Metals Content (for example, TestMethod D 482), adhesive property measurements, and corro-sion i

22、nhibiting characteristics may be specified, if needed, andshall be as agreed-upon between the producer and the pur-chaser.9.3 The purchaser (individual cable manufacturer or other)shall specify any other expected requirements needed to ensurecompliance with such end-product requirements as cabledrip

23、-out temperature and jacket slip.10. Quality Assurance10.1 Responsibility for Inspection and TestsUnless other-wise specified in the contract or purchase order, the producer isresponsible for the performance of all inspection and testrequirements specified herein. The producer may use his ownor any

24、other suitable facilities for the performance of theinspection and test requirements specified herein, unless oth-erwise stated by the purchaser in the order or at the time of thecontract signing. The purchaser shall have the right to performany of the inspections and tests set forth in this specifi

25、cationwhere such inspections are deemed necessary to assure that thematerial conforms to prescribed requirements.10.2 Each producer shall establish written nominal valuesand tolerances for the material properties routinely checked.For properties not routinely checked, typical values shall bespecifie

26、d. Once these values have been accepted by thepurchaser, the producer shall not ship material which deviatesfrom these limits without prior notification to and approval bythe purchaser.10.3 An inspection lot shall consist of an identifiable quan-tity of the same material subjected to inspection at o

27、ne time.11. Certification11.1 The producer or supplier shall, on request, furnish tothe purchaser a certificate stating that each lot has beensampled, tested, and inspected in accordance with this speci-fication, and has met the requirements.12. Packaging and Package Marking12.1 PackagingThe floodin

28、g compound shall be pack-aged in a manner that protects the material from contaminationduring shipment.12.2 Package MarkingShipping containers shall bemarked with the name of the manufacturer, trade name, type ofmaterial, lot number, mass or volume, and date of manufacture.13. Keywords13.1 adhesive;

29、 compatibility; flooding compound; moisturebarrier; telecommunications wire and cableD4730022ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determinati

30、on of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdr

31、awn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your

32、comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D4730023