ASTM D4847-2002 Standard Specification for Woven Awning and Canopy Fabrics《机织遮阳篷和遮雨檐织物的标准规范》.pdf

1、Designation: D 4847 02Standard Performance Specification forWoven Awning and Canopy Fabrics1This standard is issued under the fixed designation D 4847; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A nu

2、mber in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This performance specification covers woven awningand canopy fabrics composed of any textile fiber or mixture offibers.1.2 These require

3、ments apply to the length and widthdirections for those properties where fabric direction is perti-nent.1.3 The following safety hazards caveat pertains only to thetest methods described in this specification: This standard doesnot purport to address all of the safety concerns, if any,associated wit

4、h its use. It is the responsibility of the user of thisstandard to establish appropriate safety and health practicesand determine the applicability of regulatory limitations priorto use.2. Referenced Documents2.1 ASTM Standards:D 123 Terminology Relating to Textiles2D 434 Test Method for Resistance

5、to Slippage of Yarns inWoven Fabrics Using a Standard Seam2D 1424 Test Method for Tearing Strength of Fabrics byFalling-Pendulum Type (Elmendorf)2D 2261 Test Method for Tearing Strength of Woven Fabricsby the Tongue (Single-Rip) Method (Constant-Rate-of-Extension Tensile Testing Machine)2D 2905 Prac

6、tice for Statements on Number of Specimensfor Textiles2D 5034 Test Method for Breaking Strength and Elongationof Textile Fabrics (Grab Test)32.2 AATCC Test Methods:48 Colorfastness to Crocking: AATCC Crockmeter Method16 Colorfastness to Light22 Water Repellency: Spray Test23 Colorfastness to Burnt G

7、as Fumes35 Water Resistance: Rain Test116 Colorfastness to Crocking: Rotary Vertical CrockmeterMethod129 Colorfastness to Ozone in the Atmosphere under HighHumidities138 Shampooing: Washing of Textile Floor CoveringsEvaluation Procedure 1 Gray Scale for Color ChangeEvaluation Procedure 2 Gray Scale

8、for StainingEvaluation Procedure 9 Step Chromatic Transference ScaleNOTE 1References to test methods in this standard give only thepermanent part of the designation of ASTM, AATCC, or other testmethods. The current editions of each test method shall prevail.3. Terminology3.1 Definitions:3.1.1 For de

9、finitions of textile terms used in this specifica-tion, refer to the individual ASTM and AATCC test methods,and to Terminology D 123.4. Specification Requirements4.1 The properties of woven awning and canopy fabricsshall conform to the specification requirements listed in Table1.5. Significance and

10、Use5.1 Fabrics intended for this end-use should meet all of therequirements listed in Table 1.5.2 It should be recognized that fabrics can be producedwith an almost infinite number of combinations of constructionvariables (for example, type of fibers, percentage of fibers, yarntwist, yarn number, wa

11、rp and pick count, chemical andmechanical finished.) Additionally, fashion or aesthetics dictatethat the ultimate consumer may find acceptable articles madefrom fabrics that do not conform to all of the requirements inTable 1.5.2.1 Hence, no single performance specification can possi-bly apply to al

12、l the various fabrics that could be utilized for thisend-use.5.3 The uses and significance of particular properties andtest methods are discussed in the appropriate sections of thespecified test methods.5.4 The significance and use of particular properties and testmethods are discussed in the approp

13、riate sections of the1This specification is under the jurisdiction of ASTM Committee D13 onTextiles and is the direct responsibility of Subcommittee D13.63 on HomeFurnishings.Current edition approved April 10, 2002. Published July 2002. Originallypublished as D 4847 88. Last previous edition D 4847

14、95a(2001).2Annual Book of ASTM Standards, Vol 07.01.3Annual Book of ASTM Standards, Vol 07.02.4Available from the American Association of Textile Chemists and Colorists,P.O. Box 12215, Research Triangle Park, NC 27709.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohock

15、en, PA 19428-2959, United States.specified test methods.6. Test Methods (see Note 1)6.1 Breaking ForceDetermine the dry breaking force, inthe standard atmosphere for testing textiles, as directed in TestMethod D 5034, using a constant rate of extension (CRE)tensile testing6.2 Resistance to Yarn Slip

16、pageDetermine the resistanceto yarn slippage as directed in Test Method D 434.NOTE 2The precision of Test Method D 434 has not been established,and it may not be suitable for fabrics with low yarn counts in terms of endsand picks.6.3 Tear StrengthDetermine the tear strength as directedin Test Method

17、 D 1424.6.4 Dimensional ChangeDetermine the maximum dimen-sional change after five cleanings, as directed in AATCC TestMethod 138.6.5 Colorfastness:6.5.1 Burnt Gas FumesDetermine the colorfastness toburnt gas fumes on the original fabric, and after one launderingor one drycleaning, as directed in AA

18、TCC Test Method 23.6.5.2 CrockingDetermine the colorfastness to dry and wetcrocking as directed in AATCC Test Method 8 or AATCC TestMethod 116, or as agreed to by the purchaser and the supplier.In case of controversy, AATCC Test Method 8 shall prevail.6.5.3 LightDetermine the colorfastness to light

19、as di-rected in AATCC Test Method 16.NOTE 3There are distinct differences in spectral distribution betweenthe various types of machines listed in AATCC Test Method 16, with nooverall correlations between them. Consequently, these machines cannotbe used interchangeably. In case of controversy, result

20、s obtained with thewater cooled xenon arc machine listed in Option E shall prevail.6.5.4 OzoneDetermine the colorfastness to ozone as di-rected in AATCC Test Method 129.6.6 Water Resistance (Rain Test)Determine the waterresistance (rain test) on the original fabric, and after onelaundering, as direc

21、ted in AATCC Test Method 35.6.7 Water RepellencyDetermine the water repellency(spray test) on the original fabric, and after one laundering, asdirected in AATCC Test Method 22.6.8 FlammabilityThe flammability requirements shall beagreed upon by the purchaser and supplier, except whenregulated by app

22、licable government mandatory standards.7. Keywords7.1 fabric; performance; specificationASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of

23、 the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn.

24、Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comme

25、nts have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or m

26、ultiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).TABLE 1 Specification RequirementsNOTE 1Class in a, b, and SA. rating is based on a numerical

27、 scale of5 for no color change, color transfer, or wrinkle, to 1 for severe colorchange, color transfer, or wrinkle.Characteristic Requirements SectionBreaking Strength (Load) 660 N (150 lbf), min 6.1Yarn Slippage 6 mm (14 in.) separa-tionat 67 N (15 lbf)6.2Tear Strength 44 N (10 lbf) min 6.3Dimensi

28、onal Change: 3 % max 6.4Colorfastness:Burnt Gas Fumes-2 cycles Grade 4Amin 6.5.1Shade Change After OneLaun deringGrade 4Amin 6.5.1CrockingDry Grade 4Bmin 6.5.2Wet Grade 3Bmin 6.5.2Light (160 AATCC SFU) Grade 4Amin 6.5.3Ozone1 cycle Grade 4Amin 6.5.4Water Resistance 6.6Categories based on mini-mum ti

29、me for 1-g (Origi-nal and After One Laun-dering)2 ft (600 mm) 30 s shower2 ft (600 mm) 2 min rain3 ft (915 mm) 5 min stormWater Repellency 6.7Smooth textured fabricsOriginal 90 minAfter laundering 70 minRough textured fabricsOriginal 80 minAfter laundering 70 minFlammability Pass 6.8AAATCC Gray Scale For Color Change.BAATCC 9Step Chromatic Transference Scale.D 48472