ASTM D5139-2012 Standard Specification for Sample Preparation for Qualification Testing of Coatings to be Used in Nuclear Power Plants《核电站用涂料合格性测试用样品制备的标准规范》.pdf

1、Designation: D5139 12Standard Specification forSample Preparation for Qualification Testing of Coatings tobe Used in Nuclear Power Plants1This standard is issued under the fixed designation D5139; the number immediately following the designation indicates the year oforiginal adoption or, in the case

2、 of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification defines the size, composition, surfacepreparation, and coating applicatio

3、n variables for preparingsamples for evaluating coatings and linings over varioussubstrates.1.2 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered st

4、andard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Refer

5、enced Documents2.1 ASTM Standards:2A36/A36M Specification for Carbon Structural SteelC33/C33M Specification for Concrete AggregatesC150/C150M Specification for Portland CementC192/C192M Practice for Making and Curing Concrete TestSpecimens in the LaboratoryC260 Specification for Air-Entraining Admix

6、tures for Con-creteC494/C494M Specification for Chemical Admixtures forConcreteC618 Specification for Coal Fly Ash and Raw or CalcinedNatural Pozzolan for Use in ConcreteD3912 Test Method for Chemical Resistance of Coatingsand Linings for Use in Nuclear Power PlantsD4258 Practice for Surface Cleanin

7、g Concrete for CoatingD4259 Practice for Abrading ConcreteD4260 Practice for Liquid and Gelled Acid Etching ofConcreteD4538 Terminology Relating to Protective Coating andLining Work for Power Generation FacilitiesD4541 Test Method for Pull-Off Strength of Coatings UsingPortable Adhesion TestersD7234

8、 Test Method for Pull-Off Adhesion Strength of Coat-ings on Concrete Using Portable Pull-Off Adhesion Tes-ters2.2 American Concrete Institute:3ACI 308 Guide to Curing ConcreteACI Cement and Concrete Terminology2.3 American National Standards Institute (ANSI):4ANSI N5.121974 Protective Coatings (Pain

9、ts) for theNuclear Industry, paragraph 7.4.33. Terminology3.1 DefinitionsDefinitions for use with this standard areshown in Terminology D4538 or other applicable standards.3.2 Definitions of Terms Specific to This Standard:3.2.1 bughole (surface air void), na small regular orirregular cavity, usuall

10、y not exceeding 1.5 mm in diameter,resulting from entrapment of air bubbles in the surface offormed concrete during placement and consolidation (ACICement and Concrete Terminology).3.2.2 curing compound, na liquid that can be applied as acoating to the surface of newly placed concrete to retard thel

11、oss of water and, in the case of pigmented compounds, toreflect heat so as to provide an opportunity for the concrete todevelop its properties in a favorable temperature and moistureenvironment (ACI Cement and Concrete Terminology).4. Significance and Use4.1 This specification provides uniform requi

12、rements for thepreparation of test samples used for testing of coatings andlinings to be used in nuclear power plants.1This specification is under the jurisdiction of ASTM Committee D33 onProtective Coating and Lining Work for Power Generation Facilities and is the directresponsibility of Subcommitt

13、ee D33.02 on Service and Material Parameters.Current edition approved July 1, 2012. Published August 2012. Originallyapproved in 1990. Last previous edition approved in 2010 as D5139 10. DOI:10.1520/D5139-12.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Custome

14、r Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American Concrete Institute (ACI), P.O. Box 9094, FarmingtonHills, MI 48333-9094, http:/www.concrete.org.4Available from American Nationa

15、l Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States14.2 At the users discretion, this standard may also be usedwhen preparing samples to be tes

16、ted for the purpose ofassessing performance attributes for coating and lining systemsthat may be applied in other types of power plants or for otherindustrial facilities.4.3 Users of this guide must ensure that coatings workcomplies not only with this guide, but also with the licenseesplant-specific

17、 quality assurance program and licensing com-mitments.5. Steel Panels5.1 Panel size shall be a minimum of 2-in. wide by 4-in.long by18-in. thick (50.8-mm wide by 101.6-mm long by3.175-mm thick) unless otherwise stated in the referenced testmethod. Edges and corners may be rounded. A suitably located

18、14 in. (6.35 mm) diameter hole may be provided in the testpanel as appropriate when required by the test method.5.1.1 For Test Method D4541 the minimum size shall be3-in. wide by 5-in. long by14-in. thick (76.2-mm wide by127-mm long by 6.35-mm thick).5.2 Unless otherwise required, all panels shall b

19、e carbonsteel, meeting the requirements of Specification A36/A36M.6. Concrete Blocks6.1 The minimum size shall be 2-in. wide by 2-in. deep by4-in. long (50.8-mm wide by 50.8-mm deep by 101.6-mmlong) unless otherwise stated in the referenced test method. Theedges may be chamfered up to14 in. (6.35 mm

20、) maximum.6.1.1 The dimensions of the block to be tested should besufficient to accommodate the adhesion tester to be used (forexample, Test Method D7234).6.2 Composition shall be as follows:Cement Specification C150/C150M,Type II7 sacks/yd3Gravel Specification C33/C33M,size38 in.45 % by volumeSand

21、Specification C33/C33M 55 % by volumeAir-entrainingadmixtureSpecification C260 As recommended4to7%Water-reducingadmixtureSpecification C494/C494M As recommendedPozzolan Specification C618 As recommendedto 15 % amountWater,demineralizedor distilled3 in. slumpNominal 1 CubicFoot BatchCement Specificat

22、ion C150/C150M,Type II low alkali22.2 lb (10.07 kg)Gravel Specification C33/C33M,Size38 in.45.3 lb (20.55 kg)Sand Specification C33/C33M 55.5 lb (25.17 kg)Air-entrainingadmixtureSpecification C260 1.05 fl oz (31 mL)Pozzolan Specification C618 2.2 lb (1.0 kg)Water-reducingadmixture(Type A)Specificati

23、on C494/C494M As recommendedby the manufacturerWater,demineralizedor distilledAs required to produce3-in. (76.2-mm) slump(approximately)6.3 Blocks shall be cast horizontally in forms using releaseagents that are compatible with the coatings/linings to be used.The top surface, as cast, shall be given

24、 a broom finish, unlessotherwise specified in the project specification. The blocksurface is to be covered with plastic during the first 24 hours tosimulate water curing unless otherwise specified.6.4 The block shall be removed from the form after 24 hoursand wet cured in accordance with ACI 308 or

25、PracticeC192/C192M.6.5 If a curing compound is to be used, apply the compoundto the top surface immediately after finishing and to all othersurfaces of the block within 2 hours after its removal from theform.6.6 Allow the block to cure for 28 days in accordance withACI 308 before application of the

26、coating system unlessotherwise specified.6.7 A suitable hanger compatible with the testing apparatusshall be affixed at the mid-point of one end of the block asappropriate when required by the test method.6.8 After removing the block from the form, place or marka reference indicator on one end of ea

27、ch block, (for example,mark with a permanent marker or otherwise describe thereference being used). This indicator will allow referencingeach face by means of the following convention (refer to Fig.1):(a) Face “A” is the top (non-formed) face(b) Viewing the indicator on the block end, Faces “B, “C,”

28、 and “D” are located clockwise from Face “A.”7. Miscellaneous Materials7.1 Follow 5.1 and 5.2 for metallic materials such asaluminum, galvanized steel, and other metals.FIG. 1 Concrete Test Block Face DesignationD5139 1227.2 Follow 6.1 and 6.3 for castable materials such as grout,fireproofing, and o

29、ther castables.8. Surface Preparation8.1 Steel:8.1.1 Surface preparation parameters shall be established.8.1.2 Users of this standard may identify project specificconditions, for example, weld configuration, corrosion pitting,interfaces/overlaps with pre-existing coatings, etc. These con-ditions sha

30、ll be specified as appropriate.8.2 Concrete:8.2.1 Surface preparation parameters shall be established.8.2.2 Users of this standard may identify project specificconditions, for example, configuration, texture, bugholes,interfaces/overlaps with pre-existing coatings, etc. These con-ditions shall be re

31、quired as appropriate.8.2.3 After curing, remove loose material on Face A (non-formed, broom finished surface) by light wire brushing. Re-move loose material on a cast surface by blowing with air (80to 100 psi), unless otherwise specified, such as PracticesD4258, D4259,orD4260.8.2.4 Bugholes, honeyc

32、omb, and other surface defects maybe simulated by drilling holes to test coating systems forpatching surface defects.9. Application9.1 All test samples shall be coated with the coating/liningsystem(s) intended for evaluation, including any applicablefillers, internal reinforcement, curing compounds

33、and sealants.Different systems may be applied to different surfaces of thesame sample. The manufacturers latest published applicationinstructions shall be followed for mixing, thinning (asapplicable), and coating/lining application unless otherwiserequired. Any special procedures or conditions shall

34、 be notedin the documentation including thinning, mixing, use ofaccelerators, drying/curing times, force curing, aging betweencoats/systems, and intermediate surface preparations.9.2 The film thickness range shall be representative of thespecific work for which the testing is being conducted.9.3 The

35、 coating system shall be fully cured as specified bythe manufacturer or licensee. Historically, some coated testpanels were cured for 30 to 45 days at 70 to 80F (21 to 27C)or force cured at a maximum temperature of 150F (66C) fora maximum of 72 hours prior to commencement of testing (seeANSI N5.1219

36、74, paragraph 7.4.3).9.4 Test samples for painting test programs may includesimulated aging of the coating when applicable, intermediatesurface preparation and wide ranges of coating filmthicknesses, as required. The sample preparation procedureshall reflect actual field conditions as closely as pos

37、sible,including surface preparation, coating/lining application andcuring methods. Any additional special requirements shall berecorded.9.5 All surfaces of concrete blocks shall be coated whentesting in accordance with Test Method D3912. One end of theblocks shall be left uncoated for all other test

38、ing.10. Documentation and Records10.1 Coating/Lining Material Data:10.1.1 Manufacturers product identification.10.1.2 Product batch number for each component.10.1.3 Product color.10.2 Minimum Sample Preparation Data:10.2.1 All sample preparation times and dates for each coat.10.2.2 Surface preparati

39、on details.10.2.3 Thinners, accelerators, additives, reinforcement, andfillers added during the mixing and application process.10.2.4 Method of application.10.2.5 Coating/lining sequence.10.2.6 Individual dry film thickness ranges of each coat andtotal thickness range.10.2.7 Environmental conditions

40、.10.2.8 Cure times and temperatures.10.3 Record any deviations or non-conformances.11. Keywords11.1 concrete blocks; nuclear power plants; sample prepa-ration; steel panels; surface preparation and coating applicationvariables; test samplesASTM International takes no position respecting the validity

41、 of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject

42、to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters

43、. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is

44、 copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D5139 123