ASTM E2031-1999(2016) Standard Practice for Quality Control of Psychophysiological Detection of Deception (Polygraph) Examinations《欺骗检查的心理生理检测 (测谎) 质量控制的标准实施规程》.pdf

1、Designation: E2031 99 (Reapproved 2016)Standard Practice forQuality Control of Psychophysiological Detection ofDeception (Polygraph) Examinations1This standard is issued under the fixed designation E2031; the number immediately following the designation indicates the year oforiginal adoption or, in

2、the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice establishes essential and recommendedprocedures for the conduct of qua

3、lity control for a Psycho-physiological Detection of Deception (PDD) examination.2. Referenced Documents2.1 ASTM Standards:2E2035 Terminology Relating to Forensic Psychophysiology3. Terminology3.1 DefinitionsFor additional terminology relating toPDD, refer to Terminology E2035.3.1.1 independent qual

4、ity control reviewan evaluation ofthe PDD examination that is free of undue influence from theoriginal examiner or other persons.3.1.2 objective quality control reviewan evaluation ofPDD test data based upon established analysis procedureswhich meet ASTM standards.3.1.3 PDD reporta written account t

5、o the person oragency requesting the examination which summarizes thedetails of an individual PDD examination. The report shouldinclude, but is not limited to: the details of the incident or thecircumstances for which the examination was conducted;identifying information of the examinee; the purpose

6、 of theexamination; identifying information of the examiner; theresults of the examination; the instrumentation utilized tocollect the test data; and any explanatory remarks determinednecessary by the examiner. For a specific issue examination, allrelevant questions and the examinees answers shall b

7、e in-cluded.3.1.4 quality controla systematic, independent, and objec-tive review, evaluation, and critique of a PDD examination bya qualified examiner. This review is designed to ensure eachexaminer maintains professional standards.4. Summary of Practice4.1 All PDD examinations may be subjected to

8、a qualitycontrol review. Prior to a PDD examination being consideredby any court or judicial tribunal, in order to ensure eachexamination meets appropriate standards, each examinationshould undergo a quality control review.4.2 Experienced examiners who are trained in the PDDformat utilized by the or

9、iginal examiner are qualified toconduct a quality control review of an examination.4.3 A quality control review shall be independent andobjective and meet all applicable ASTM standards. The qualitycontrol process should involve, but is not limited to a reviewof: the test data analysis of all charts

10、collected during theexamination; all questions and answers utilized during theexamination to produce the data which were evaluated; thePDD report; any available electronic recordings; and all alliedpaperwork completed by the PDD examiner in support of theexamination.4.4 The person conducting the qua

11、lity control review shallattest, in writing, as to whether the test data supports theconclusion rendered by the original examiner.4.5 All PDD documents and test data shall remain availablefor a quality control review for no less than a year or until theincident or circumstance requiring the examinat

12、ion to beconducted has been completely adjudicated.5. Keywords5.1 forensic psychophysiology; PDD; psychophysiologicaldetection of deception; quality control; standards1This practice is under the jurisdiction of ASTM Committee E52 on ForensicPsychophysiology and is the direct responsibility of Subcom

13、mittee E52.03 onQuality Control.Current edition approved Jan. 1, 2016. Published January 2016. Originallyapproved in 1999. Last previous edition approved in 2010 as E2031 99 (2010).DOI: 10.1520/E2031-99R16.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer

14、Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1ASTM International takes no position resp

15、ecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This s

16、tandard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM Interna

17、tional Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown bel

18、ow.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 99 (2016)2