ASTM E921-1997(2003) Standard Specification for Export Packaged Laboratory Apparatus《出口包装的实验室装置》.pdf

1、Designation: E 921 97 (Reapproved 2003)Standard Specification forExport Packaged Laboratory Apparatus1This standard is issued under the fixed designation E 921; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revis

2、ion. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.INTRODUCTIONThis specification is proposed as a performance standard to be met for items that will be exported.The standard would apply onl

3、y when requested by the buyer.1. Scope1.1 This specification covers the procedures for testingloaded shipping containers. Drop, vibration and compressiontests are performed to measure the ability of the shippingcontainer to protect the product from shock, vibration andcompressive forces encountered

4、during normal export handlingand shipping conditions. This specification is not intended tosupplant material specifications or existing preshipment testprocedures. This specification is not intended for use withhazardous materials.1.2 These procedures are suitable for all types of laboratoryapparatu

5、s, including reusable and disposable macro and microproducts.1.3 The following precautionary caveat pertains only to thetest method portion, Section 4, of this specification: Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility

6、 of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2. Referenced Documents2.1 ASTM Standards:D 642 Test Method for Determining Compressive Resis-tance of Shipping Containers, Components, and UnitLoa

7、ds2D 685 Practice for Conditioning Paper and Paper Productsfor Testing2D 999 Methods for Vibration Testing of Shipping Contain-ers2D 1083 Test Methods for the Mechanical Handling ofUtilized Loads and Large Shipping Cases and Crates2D 3951 Practice for Commercial Packaging2D 4169 Practice for Perform

8、ance Testing of Shipping Con-tainers and Systems2D 5276 Test Method for Drop Test of Loaded Containers byFree Fall23. Requirements3.1 Three individual shipping containers, or one unit con-sisting of two or more overpackaged individual units arerequired. Each specimen shall be run through the sequenc

9、e oftests, in the order given.3.2 Condition test specimens in accordance with PracticeD 685. Standard conditions must be maintained throughout thetest sequence.3.3 The packaging shall comply with Practice D 3951except cleanliness of laboratory apparatus shall be as requiredby the Product Standard, t

10、he Quality Assurance Standard, or asagreed upon between the manufacturer and the purchaser.4. Procedure4.1 Determine the test levels in accordance with PracticeD 4169.4.2 For items less than 100 lb, perform drop test inaccordance with Test Method D 5276.4.2.1 Determine the drop test levels of the sp

11、ecimen fromthe following:Gross Weight, lb (kg) Drop Height, in. (mm)0 to 20 lb (0 to 9.1 kg) 24 in. (610 mm)20 to 40 lb (9.1 to 18.1 kg) 21 in. (533 mm)40 to 60 lb (18.1 to 27.2 kg) 18 in. (457 mm)60 to 80 lb (27.2 to 36.3 kg) 15 in. (381 mm)80 to 100 lb (36.3 to 45.4 kg) 12 in. (305 mm)4.2.2 Perfor

12、m the following drop sequence: bottom at twicespecified height; bottom long edge at specified height; bottomadjacent short edge at specified height; bottom corner atspecified height; bottom diagonal opposite corner at specifiedheight; and top at specified height.4.3 For drop test items more than 100

13、 lb, proceed with thefollowing (Test Methods D 1083):1This specification is under the jurisdiction of ASTM Committee E41 onLaboratory Apparatus and is the direct responsibility of Subcommittee E41.01 onGlass Apparatus.Current edition approved Nov. 10, 1997. Published February 1998. Originallypublish

14、ed as E 921 83. Last previous edition E 921 96.2Annual Book of ASTM Standards, Vol 15.09.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.4.3.1 Determine the drop test levels in accordance withPractice D 4169:Gross Weight Drop Height1

15、00 to 500 lb 2 in.500 lb and Over 9 in.4.3.2 Perform the following drop sequence: one drop oneach bottom edge. The total number of drops shall be four.4.4 Perform the compression test in accordance with TestMethod D 642.4.4.1 Compression test level in accordance with PracticeD 4169 where F = 4.4 and

16、 H = 120 in.4.4.2 Use the following test level:L 5 W120 2 H!H!3 4.5 (1)where:L = load,W = weight of one shipping container, andH = height of one shipping container in in.5. Acceptable Criteria5.1 Disposable GlassCompletion of testing withoutbreakage occurring in any of the three units tested. In the

17、 caseof bulk packed items (more than 50 in a shipping container)less than 3 % total breakage in each of the three units tested.5.2 All OtherCompletion of testing without breakageoccurring in any of the three units tested.5.3 Outer package must contain product and provide adegree of protection to con

18、tents. One complete retest consist-ing of three (3) new packages is permitted.6. Report6.1 Each supplier shall maintain on file laboratory testreports verifying successful testing as outlined in this specifi-cation and if required, with each order issue a certification, inwriting, that states that p

19、ackaging complies with this specifi-cation.7. Keywords7.1 apparatus; export; laboratory; packagingASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determ

20、ination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or w

21、ithdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that

22、your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).E 921 97 (2003)2