ASTM F1070-1987(2004) Standard Specification for Doors Non-Tight for Marine Use《船用非密闭门》.pdf

1、Designation: F 1070 87 (Reapproved 2004)An American National StandardStandard Specification forDoors, Non-Tight, for Marine Use1This standard is issued under the fixed designation F 1070; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revis

2、ion, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification to be used in conjunction with Speci-fication F 1073, covers the principal dimens

3、ions and themechanical requirements for manufacturing steel, aluminum,and glass-reinforced plastic non-tight, personnel doors anddutch doors, with the exception of joiner, joiner dutch doors,and expanded metal doors, for marine use.1.2 The doors will be used in non-tight bulkheads.1.3 When fire prot

4、ection requirements are applicable to thelocation of these doors, then the use of aluminum and glass-reinforced plastic doors shall be unacceptable.1.4 The values stated in inch-pound units are to be regardedas the standard. The values given in parentheses are forinformation only.2. Referenced Docum

5、ents2.1 ASTM Standards:2A 36/A 36M Specification for Carbon Structural SteelA 131/A 131M Specification for Structural Steel for ShipsB 209 Specification for Aluminum and Aluminum-AlloySheet and PlateF 1073 Specification for Door Fittings, for Watertight/Gastight/Airtight, Weathertight, and Non-Tight

6、 Doors, forMarine Use2.2 ABS Standard:3Rules for Building and Classing Steel Vessels2.3 Military Standards:4MIL-P-17549 Plastic Laminates, Fibrous Glass Reinforced,Marine StructuralMIL-R-21607 Resins, Polyester Low-Pressure Laminating,Fire RetardantMIL-P-24441 Epoxy-Polyamide PaintMIL-C-81706 Coatin

7、g, Aluminum and Aluminum AlloysTT-E-490 Enamel, Silicone Alkyd Copolymer, Semi-gloss,ExteriorDoD-STD-2138 Metal Sprayed Coating Systems for Corro-sion Protection3. Ordering Information3.1 Ordering for doors under this specification shall includethe following:3.1.1 Type of door and material (see Tabl

8、e 1 and Figs. 1-3),3.1.2 Nominal and ASTM designations,3.1.3 Quantity, hand of door (right hand or left hand, orboth), and3.1.4 Optional items, such as fixed lights, door locks, to beindicated.3.2 Inspection and acceptance of doors shall be agreed uponbetween the purchaser and the supplier.4. Materi

9、als and Manufacture4.1 The materials and specifications shall be as given inTable 1.4.2 Glass-reinforced plastic (GRP) material of doors shallmeet the requirements of MIL-P-17549, Grade 1. In addition,laminate must have the flammability limits equal to therequirements for Grade 2, Class A of MIL-R-2

10、1607.5. Construction, Shape, and Dimensions5.1 The construction, shape, and clear opening dimensionsshall be as shown in Tables 1 and 2 and Figs. 1-3 and conformto the following requirements:5.1.1 A right-hand opening door shall be construed as onethat opens towards you with hinges located on right

11、side ofdoor. A left-hand opening is similar but with hinges on the left.5.1.2 The size of the door opening and shape shall be asgiven in Table 2.5.1.3 Figs. 1 and 2 show the right-hand opening, and in thecase of left-hand opening, the arrangement of fittings shall bereversed.5.1.4 The position of th

12、e grab handles shall be located onthe center of the height of both sides of the door; in the case ofdutch doors, the location of the grab handles shall be suitablypositioned in the top panel.1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the

13、direct responsibility of Subcommittee F25.03 onOutfitting and Deck Machinery.Current edition approved Nov. 1, 2004. Published November 2004. Originallyapproved in 1987. Last previous edition approved in 1999 as F 1070 87 (1999).2For referenced ASTM standards, visit the ASTM website, www.astm.org, or

14、contact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American Bureau of Shipping, ABS Plaza, 16855 NorthchaseDr., Houston, TX 77060.4Available from Standardization Docume

15、nts Order Desk, Bldg. 4 Section D, 700Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.1.5 The material of the standard door components shall beas shown in Table 1.5.1.6 Doors s

16、hall be fitted with dogs, hinges, hasp and stapleassemblies, grab handles, label plates, and hook assemblies; fordetails, see Specification F 1073.5.1.7 Welding shall be done in accordance with the Rules ofAmerican Bureau of Shipping.6. Workmanship, Finish, and Appearance6.1 All sharp and ragged edg

17、es shall be ground flush andremoved for personnel protection.6.2 Pretreatment and priming of door components shall beas follows:NOTE 11 in. = 25.4 mm.FIG. 1 Non-Tight Doors (Square Corners)FIG. 2 Non-Tight Doors (Radius Corners)F 1070 87 (2004)26.2.1 Steel doors and components shall be coated within

18、organic zinc-rich primer SSPC Paint 20 Type I-C at 1.5 to 3.0mil (MDFT), both sides before assembly, following surfacepreparation in accordance with the manufacturers instructions.6.2.2 Aluminum doors and components are to be pretreatedwith wash primer coating followed with lead-free, chromate-free,

19、 anticorrosion prime coating. Pretreatment and primer areto be applied before assembly, following surface preparation,in accordance with the manufacturers instructions.NOTE 12.2 lb=1kg.NOTE 21 in. = 25.4 mm.FIG. 3 Ships Non-Tight Steel DoorsTABLE 1 Standard Door MaterialsNumber ComponentMild SteelAl

20、uminumGlass-Reinforced Plastic(GRP)1 door panel Specifications A 36/A 36M orA 131/A 131MSpecification B 209 MIL-P-17549, Grade 12 stiffeners Specifications A 36/A 36M orA 131/A 131MSpecification B 209 integralTABLE 2 DoorNon-TightUNITS: INCHESNOTE 11 in. = 25.4 mm.NominalNo.Size of Opening DoorCalcu

21、latedMass, lbWidth Height W H h26542666 265466 27556716.525.58310130603063 306063 31616422241051103066 66 67 25.5 116F 1070 87 (2004)36.2.3 GRP doors and components are to have color tint“haze gray” painted upon completion of the molding process.7. Product Marking7.1 Each door shall be marked with t

22、he purchase ordernumber by attaching a CRES label plate to the door panel usingletters at least12 in. (12.7 mm) high, indicating the ASTMdesignation number, nominal number, thickness of door plate,and direction of opening. Other markings may be in paint.7.2 Label plates shall be screwed or bolted to

23、 the door panelon steel and aluminum doors.7.3 GRP door label plates shall be affixed to the door withepoxy.8. Packaging and Package Marking8.1 Doors shall be crated or attached to a pallet in a manneracceptable for shipment by a common carrier. The door anddoor frame assembly shall be shipped as on

24、e unit, with gasketprotected from knife edge by an inserted partition.9. Keywords9.1 doors; dutch doors; marine; non-tight doors; personneldoors; shipSUPPLEMENTARY REQUIREMENTSThe following supplementary requirements shall apply only when specified by the contract or order.S1. Pretreatment and Primi

25、ng of Door ComponentsS1.1 Pretreatment and priming of door components shallconsist of metal spray coating in accordance with DoD-STD-2138, Type II, on both sides before assembly.S2. Aluminum Doors and ComponentsS2.1 Aluminum doors and components shall be treated witha chemical conversion coating MIL

26、-C-81706, followed with asecond coat of epoxy polyamide primer (Formula 150 ofMIL-P-24441) alkyd haze gray (TT-E-490 or equal). Coatingto be applied before assembly, following surface preparation,in accordance with the manufacturers instruction.ASTM International takes no position respecting the val

27、idity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is sub

28、ject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headqua

29、rters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standa

30、rd is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F 1070 87 (2004)4