ASTM F1447-2018 Standard Specification for Helmets Used in Recreational Bicycling or Roller Skating.pdf

1、Designation: F1447 18 An American National StandardStandard Specification forHelmets Used in Recreational Bicycling or Roller Skating1This standard is issued under the fixed designation F1447; the number immediately following the designation indicates the year oforiginal adoption or, in the case of

2、revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers performance requirements forhelmets manufactured for use by recreation

3、al bicyclists orroller skaters. This specification recognizes the desirability oflightweight construction and ventilation; however, it is aperformance standard and is not intended to restrict design.1.2 All testing and requirements of this specification shallbe in accordance with Test Methods F1446,

4、 except where notedherein.1.3 Partial utilization of this specification is prohibited. Anystatement of compliance with this specification shall be acertification that the product meets all of the requirements ofthe specification in its entirety. A product that fails to meet anyone of the requirement

5、s of this specification is considered tohave failed the standard and should not be sold with anyindication that it meets parts of the standard.1.4 This standard is subject to revision at any time byASTM. It must be reviewed every five years and if not revisedeither reapproved or withdrawn. Reference

6、s to the standardmust include the version date. No references to a version thathas been replaced or withdrawn shall be placed on any productor its packaging manufactured more than 24 months after theeffective revision or withdrawal date. Go to astm.org to verifythe latest version of this standard.NO

7、TE 1The current edition of this standard was approved on June 1,2018.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-m

8、endations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2F1446 Test Methods for Equipment and Procedures Used inEvaluating the Performance Characteristics of ProtectiveHeadgearF2043 Classification for Bicycle Usage3. Termi

9、nology3.1 Definitions of Terms Specific to This Standard:3.1.1 recreational bicycling, nbicycling in conditions upto Condition 3 as specified in Classification F2043.3.1.2 in-lines, nroller skates with all wheels on each skatearranged along a single longitudinal line.3.1.3 quads, nroller skates with

10、 four wheels on each skatearranged in a rectangular pattern.3.1.4 recreational roller skating, nskating horizontallyusing quads or in-lines but not roller hockey or trick rollerskating such as ramp jumping, sliding sideways, or skating onstairs.4. Headforms4.1 Headforms to be used in this specificat

11、ion are asspecified in the section on Test Headforms of Test MethodsF1446, using the variable mass drop assembly configuration.The appropriate size headform shall be selected in accordancewith the section on Headform Size of Test Methods F1446 forthe helmet to be tested.4.2 In addition to the provis

12、ions of Test Methods F1446, thecenter of gravity of the headform must be within a 10 verticalcone from the center of impact and lie within a rectangular area28 by 12.8 mm oriented as shown in Fig. 1. The center ofgravity of the drop assembly shall lie within 6.4 mm millime-ters of the Z-X plane, whi

13、ch is defined for twin wire systems asthe plane containing the axes of the two guide wires, and formonorail systems as the plane containing the design center of1This specification is under the jurisdiction of ASTM Committee F08 on SportsEquipment, Playing Surfaces, and Facilities and is the direct r

14、esponsibility ofSubcommittee F08.53 on Headgear and Helmets.Current edition approved June 1, 2018. Published June 2018. Originallyapproved in 1993. Last previous edition approved in 2012 as F1447 12. DOI:10.1520/F1447-18.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact

15、 ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard

16、 was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1the headf

17、orm and the axis of the monorail. The center ofgravity of the drop assembly shall lie within 6.4 mm of the Y-Zplane on the side opposite the arm of the ball arm and within21.6 mm of the Y-Z plane on the side containing the ball armwhere the Y-Z plane is perpendicular to the Z-X plane andcontains the

18、 design center of the headform. Please see Fig. 1.The center of the anvil must be fixed in alignment with thecenter vertical axis of the accelerometer.5. Anvils and Impact Velocities5.1 Anvils to be used for impact tests in this specificationare the flat, hemispherical, and curbstone anvils describe

19、d inthe section on Apparatus of Test Methods F1446.5.2 The helmet shall be dropped onto the flat anvil toachieve an impact velocity of 6.2 m/s (corresponding to atheoretical drop height of 2.0 m).5.3 The helmet shall be dropped onto the hemispherical andcurbstone anvils to achieve an impact velocity

20、 of 4.8 m/s(corresponding to a theoretical drop height of 1.2 m).5.4 The impact velocity shall be measured during the last 40mm of free-fall for each test and shall be within 63 % of thevelocities specified in 5.2 and 5.3.6. Marking the Test Line (Area of Required Coverage)6.1 Place the helmet on th

21、e appropriate size headform inaccordance with the section on Headform Size Selection ofTest Methods F1446 and preload with a preload ballast weightof 5 kg.6.2 Position the helmet as specified by the manufacturershead positioning index (HPI) with the brow parallel to the basicplane.6.3 Draw a line A-

22、B-C-D on the helmet as shown in Fig. 2.This represents the test line defined in Test Methods F1446.7. Conditioning, Number of Samples and LaboratoryEnvironment7.1 The test normally requires eight samples of each shell/liner combination.7.2 Conditioning of the samples to be tested is described inthe

23、section on Conditioning Environment of Test MethodsF1446, except that the ambient sample may be conditioned inan environment at 17 to 27C with a relative humidity of 20 to80 %, and the wet sample is to be submerged inverted inpotable water at a temperature of 17 to 27C to an externalcrown depth of a

24、t least 305 6 25 mm.8. Impact Sites and Projections8.1 Impact sites are described in the section on Impact Sitesand Anvils of Test Methods F1446.8.2 ProjectionsAny unfaired projection extending morethan 7 mm from the helmets outer surface shall break away orcollapse when impacted with forces equival

25、ent to those pro-duced by applicable impact-attenuation tests in Section 5.There shall be no fixture on the helmets inner surfaceprojecting more than 2 mm into the helmet interior exceptoccipital stabilizers and foam fit pads.9. Impacting Schedule9.1 All impacting shall be performed in accordance wi

26、thTest Methods F1446.9.2 Helmets shall be impacted with the anvils centered on orabove the test line described in Section 6.9.3 The test anvils can be oriented in any horizontal,centered position.9.4 One each hot, cold, wet, and ambient helmet shall beimpacted using the flat and hemispherical anvils

27、 only.NOTE 1Overview of ball-arm as installed on impact test apparatus.NOTE 2Coordinate system as defined in FMVSS 218, revised April 6, 1988. Z axis positive downward (into page).FIG. 1 Center of Gravity for Drop AssemblyF1447 1829.5 The curbstone anvil shall be used to impact one timeeach of the s

28、econd set of four samples, one conditioned undereach of the four conditioning environments.9.6 In accordance with the section on Test Schedule of TestMethods F1446, retention system testing (see Section 11) shallbe completed prior to impact testing.10. Peak Acceleration Requirements10.1 The peak acc

29、eleration (g, max) of the impulse duringthe impact shall be measured with equipment described in thesection on Apparatus of Test Methods F1446.10.2 The peak acceleration of any impact shall not exceed300 g.11. Retention System Testing11.1 The ambient helmet shall be subjected to the positionalstabil

30、ity (roll-off) test in accordance with Test Methods F1446,usinga4kgdrop mass from a height of 0.6 m.11.2 Dynamic Strength Retention TestThe hot, cold, andwet helmets shall be subjected to the dynamic retention testdescribed in Test Methods F1446, using a drop mass of 4 kgdropped a distance of 0.6 m.

31、11.2.1 The helmet shall satisfy the requirements of TestMethods F1446 and the retention system shall not elongatemore than 30 6 0.8 mm.12. Labels and Warnings12.1 In addition to the labeling requirements outlined in TestMethods F1446, the helmet shall have one of the followinginscriptions on an inte

32、rior permanent label:”For use in recreational bicycling but not trick bicycling ordownhill mountain bike racing.”For use in recreational roller skating but not trick rollerskating or roller hockey.”For use in recreational bicycling or roller skating but nottrick bicycling or roller skating, downhill

33、 mountain bikeracing, or roller hockey.”13. Keywords13.1 bicycling; protective headgear ; roller skating; helmetHeadformSizeDimensionXL/2 YRSTA 24.0 88.0 89.7 38.0 23.0 137.0C 25.0 91.0 92.7 38.5 23.5 141.5E 26.0 94.5 96.0 39.0 24.0 146.5J 27.5 101.0 102.5 41.0 25.0 155.0M 29.0 106.0 107.0 41.0 27.0

34、 161.0O 30.0 108.5 110.0 42.0 27.0 164.5FIG. 2 Marking the Test LineF1447 183ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validi

35、ty of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your commen

36、ts are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have no

37、t received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple cop

38、ies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 184