ASTM F1648-1995(2003) Standard Test Methods for Archery Bowstring Component-Serving String Material《射箭弓弦元件的标准试验方法 弓弦用材料》.pdf

1、Designation: F 1648 95 (Reapproved 2003)An American National StandardStandard Test Methods forArchery Bowstring ComponentServing String Material1This standard is issued under the fixed designation F 1648; the number immediately following the designation indicates the year oforiginal adoption or, in

2、the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 These test methods cover the classification and testingof serving string as a compo

3、nent material used in the fashion-ing of archery bowstrings.1.2 These test methods are not intended to provide informa-tion beyond any evaluation of the serving string material thatwould determine its fitness for use other than in the fabricationof the completed bowstring.1.3 This standard does not

4、purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:

5、2D 76 Specification for Tensile Testing Machines for TextilesD 123 Terminology Relating to TextilesD 204 Test Methods for Sewing ThreadsD 1776 Practice for Conditioning and Testing TextilesD 2256 Test Method for Tensile Properties of Yarns by theSingle-Strand Method3. Terminology3.1 Definitions:3.1.

6、1 bowstringcompleted assembly constructed in partfrom multiple strands of cord materials lashed at the center orthe loop ends with serving string materials and used to connectthe limbs of a bow by which to launch an arrow.3.1.2 diametera measure of the thickness of the servingstring material.3.1.3 e

7、longationthe amount that a serving string materialstretches; measured as a percentage of the original length eitherat the point of rupture or at some other interval of applied load.3.1.4 serving stringapplied to a variety of natural orman-made textile materials, serving string material may be ofmono

8、cord, twisted, cable, braided, or monofilament construc-tion.3.1.5 standard conditiona condition reached by materialwhen in moisture equilibrium with a standard atmosphere of agiven temperature and relative humidity.3.1.6 strengththe maximum force applied to a servingstring material causing it to br

9、eak.4. Significance and Use4.1 These test methods are intended to provide basic infor-mation for evaluation and procurement for the user of servingstring materials for bowstrings.4.2 These test methods are not meant to be all inclusivesince special circumstances may occur that dictate the use ofnonc

10、onforming procedures for evaluation. These special cir-cumstances and the requirements they establish cannot betotally anticipated and therefore must be considered on anindividual basis.5. Test Methods5.1 Refer to Practice D 1776 for standard condition require-ments.5.1.1 Standard Conditions70 6 2F

11、(21 6 1C), 65 62 % relative humidity.5.2 Refer to Test Method D 2256 for strength and elonga-tion requirements.5.2.1 Set CRE-type testing machine at 12 6 0.5-in. (305 610-mm)/min draw rate with gage length as follows:5.2.1.1 10 6 0.1 in. (250 6 3 mm) from nip for pneumaticflat-faced clamps, or5.2.1.

12、2 5 6 0.1-in. (125 6 3-mm) free gage length forcapstan-type clamps.5.2.1.3 Report test results as the average of five test speci-mens per sample and the average of three test samples.5.2.2 Elongation tests using capstan clamps are measured at80 % of test specimen average breaking load using 100-mmin

13、dex marks arbitrarily marked along the 5-in. free gage lengthdue to possible stretching of the test specimen around thecapstans. Arbitrarily mark 100-mm index marks along the 5-in.free gage length of the mounted test specimen, and measure thechange in length of index marks after applying load to the

14、 test1These test methods are under the jurisdiction of ASTM Committee F08 onSports Equipment and Facilities and are the direct responsibility of SubcommitteeF08.16 on Archery Products.Current edition approved May 10, 2003. Published July 2003. Originallyapproved in 1995. Last previous edition approv

15、ed in 1995 as F 1648 95.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Ba

16、rr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.specimen equal to 80 % of test specimen average breakingload. Report test results entitled as EASL 80 % as the averageof five test specimens per sample and the average of three testsamples.5.3 Refer to Test Method D 204 fo

17、r diameter requirements.5.3.1 Diameter0.375 6 0.001-in. (9.52 6 0.02-mm) anvilweighted to apply 6 6 0.1 ozf (1.67 6 0.03 N). Report the testresults as the average of five test specimens and the average ofthree test samples.6. Keywords6.1 bowstring; diameter; elongation; serving string; strengthASTM

18、International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are enti

19、rely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand

20、 should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on

21、 Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F 1648 95 (2003)2