ASTM F2032-2015 Standard Specification for Helmets Used for BMX Cycling《BMX赛车用头盔的标准规格》.pdf

1、Designation: F2032 15 An American National StandardStandard Specification forHelmets Used for BMX Cycling1This standard is issued under the fixed designation F2032; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last r

2、evision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers performance requirements forhelmets used in BMX cycling. Studies have shown higher riskto the head

3、 and face for this sport as compared to recreationalstreet riding; therefore, this specification requires impact pro-tection over a larger area of the head than Specification F1447and the CPSC standard. This specification also providesperformance criteria for helmets equipped with chin bars.1.2 All

4、testing and requirements of this specification shallbe in accordance with Test Methods F1446 except where notedherein.1.3 Partial utilization of this specification is prohibited. Anystatement of compliance with this specification shall be acertification that the headgear with faceguard meets all of

5、therequirements of the specification in their entirety. A headgearwith faceguard that fails to meet any one of the requirements ofthis specification is considered to have failed the specification,and shall not be sold with any indication that it meets parts ofthe specification.1.4 Headgear designed

6、to comply with this and otherstandards may proclaim uses as certified by the manufacturer.1.5 The values stated in SI units are to be regarded asstandard.1.6 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of t

7、his standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2F1446 Test Methods for Equipment and Procedures Used inEvaluating the Performance Characteristics of ProtectiveHeadgea

8、rF1447 Specification for Helmets Used in Recreational Bicy-cling or Roller Skating3. Labels and Warnings3.1 Shall meet the requirements of Test Methods F1446.3.2 Shall have the words “For BMX bicycle riding andracing.”4. Marking the Test Line4.1 The test line is shown in Fig. 1 and shall be marked i

9、naccordance with Test Methods F1446.5. Conditioning and Number of Samples5.1 Shall be in accordance with Test Methods F1446.5.2 The test requires a minimum of four samples of eachshell/liner combination, with a fifth sample required for fullface helmets with a chin bar.6. Retention System Testing6.1

10、 Retention system tests shall be performed before impacttesting.6.2 The ambient helmet shall be subjected to the Roll-OffTest of Test Methods F1446 usinga4kgdrop mass from aheight of 0.6 m.6.3 The retention system shall remain intact and the helmetshall remain on the headform.6.4 The hot, cold, and

11、wet helmets shall be subjected to theDynamic Strength Retention Test of Test Methods F1446 usinga 4 kg drop mass from a height of 0.6 m.6.5 The retention system shall remain intact without elon-gating more than 30 mm.7. Impact Sites and Projections7.1 Impact sites are described in Test Methods F1446

12、.7.2 ProjectionsAny unfaired projection extending morethan 7 mm from the helmets outer surface shall break away orcollapse when impacted with forces equivalent to those pro-duced by applicable impact-attenuation tests in Section 5.There shall be no fixture on the helmets inner surface1This specifica

13、tion is under the jurisdiction of ASTM Committee F08 on SportsEquipment, Playing Surfaces, and Facilities and is the direct responsibility ofSubcommittee F08.53 on Headgear and Helmets.Current edition approved May 15, 2015. Published June 2015. Originallyapproved in 2000. Last previous edition appro

14、ved in 2011 as F2032 06 (2011).DOI: 10.1520/F2032-15.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyrigh

15、t ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1projecting more than 2 mm into the helmet interior exceptoccipital stabilizers and foam fit pads.8. Impacting Schedule8.1 All impacting shall be performed in accordance withTest Methods F1446, u

16、sing the variable mass drop assemblyconfiguration.8.2 Helmets shall be impacted with the anvils centered on orabove the test line described in Fig. 1.8.3 The test anvils can be oriented in any horizontal,centered position.8.4 For full face helmets with a chin bar, a fifth ambienthelmet shall be test

17、ed in accordance with Section 10 below.9. Impact Testing9.1 Retention system testing shall be completed prior toimpact testing.9.2 The helmet can be impacted such that the theoreticalcenter of impact described in Test Methods F1446 is anywhereon or above the test line with the curbstone anvil in any

18、horizontal orientation.9.3 Anvils to be used are the flat, hemispherical, andcurbstone anvils from Test Methods F1446.9.4 The helmet shall be dropped onto the flat anvil toachieve an impact velocity of 6.2 m/s 6 3 % (corresponding toa theoretical drop height of 2.0 m).HeadformSizeDimensionX L/2 Y R

19、S T UA 24.0 88.0 89.7 38.0 23.0 142.0 84.0C 25.0 91.0 92.7 38.5 23.5 146.5 86.0E 26.0 94.5 96.0 39.0 24.0 151.0 88.0J 27.5 101.0 102.5 41.0 25.0 160.0 92.0M 29.0 106.0 107.0 41.0 27.0 166.0 96.0O 30.0 108.5 110.0 42.0 27.0 170.0 97.0FIG. 1 Marking the Test LineF2032 1529.5 Hemispherical and curbston

20、e anvil impacts shallachieve an impact velocity of 4.8 m/s 6 3 % (corresponding toa theoretical drop height of 1.2 m).9.6 Each helmet shall be given two flat anvil impacts andone each hemispherical and curbstone anvil impact in anysequence.9.7 The theoretical center of each impact site shall besepar

21、ated from the theoretical center of other impact sites by aminimum of 120 mm.9.8 The peak acceleration of each impact shall not exceed300 g.10. Chin Bar Rigidity Test10.1 The chin bar rigidity test applies to helmets with a chinbar only.10.2 If a chin bar is present, it shall be tested in accordance

22、with the procedures in Test Methods F1446, Chin Bar RigidityTest, with an impact velocity of 2.8 m/s 6 5 % (correspondingto a theoretical drop height of 0.4 m), using a fifth ambientsample that has not been subjected to any other impact testing.11. Keywords11.1 bicycle; BMX; helmetsASTM Internationa

23、l takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their o

24、wn responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be a

25、ddressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards,

26、at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 153