ASTM F656-2002 Standard Specification for Primers for Use in Solvent Cement Joints of Poly(Vinyl Chloride) (PVC) Plastic Pipe and Fittings《聚氯乙烯塑料管和配件的溶剂胶结接口用打底剂的标准规范》.pdf

1、Designation: F 656 02An American National StandardStandard Specification forPrimers for Use in Solvent Cement Joints of Poly(VinylChloride) (PVC) Plastic Pipe and Fittings1This standard is issued under the fixed designation F 656; the number immediately following the designation indicates the year o

2、foriginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers requirements for primers foruse

3、 with poly(vinyl chloride) (PVC) pipe and fittings that are tobe joined by PVC solvent cements meeting the requirements ofSpecification D 2564.1.2 These primers are used in pressure and nonpressureapplications with plain end pipe and either socket-type fittingsor bell end pipe. These primers prepare

4、 the surface of pipe andfittings before the application of solvent cement. The primerseffect on the set and cure time of the joint is dependent on thecement, pipe size, application method, temperature, and hu-midity.1.3 Aprocedure for using the primer with cement is given inPractice D 2855.1.4 The t

5、ext of this specification references notes, footnotes,and appendixes which provide explanatory material. Thesenotes and footnotes (excluding those in tables and figures) shallnot be considered as requirements of the specification.1.5 The values stated in inch-pound units are to be regardedas the sta

6、ndard. The values given in parentheses are forinformation only.1.6 The following safety hazards caveat pertains only to thetest methods portion, Section 6, of this specification: Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibi

7、lity of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2. Referenced Documents2.1 ASTM Standards:D 1600 Terminology for Abbreviated Terms Relating toPlastics2D 1784 Specification for Rigid Poly(Viny

8、l Chloride) (PVC)Compounds and Chlorinated Poly(Vinyl Chloride)(CPVC) Compounds2D 2564 Specification for Solvent Cements for Poly(VinylChloride) (PVC) Plastic Piping Systems3D 2855 Practice for Making Solvent-Cemented Joints withPoly(Vinyl Chloride) (PVC) Pipe and Fittings3F 402 Practice for Safe Ha

9、ndling of Solvent Cements,Primers, and Cleaners Used for Joining Thermoplastic Pipeand Fittings3F 412 Terminology Relating to Plastic Piping Systems3F 493 Specification for Solvent Cements for ChlorinatedPoly(Vinyl Chloride) (CPVC) Plastic Pipe and Fittings32.2 NSF Standards:Standard No. 14 for Plas

10、tic Piping Components and RelatedMaterials4Standard No. 61 for Drinking Water SystemsComponentsHealth Effects43. Terminology3.1 DefinitionsDefinitions are in accordance with Termi-nology F 412, and abbreviations are in accordance with Ter-minology D 1600, unless otherwise specified.4. Material Requi

11、rements4.1 The primer shall be an organic liquid with water-likeviscosity and shall not contain any undissolved particles.4.2 The solvent system to be used in the formulation of thisprimer is not specified.NOTE 1If required for identification purposes, colorants shall be usedin the primer. It is rec

12、ommended that orange not be used, since this is therecommended color for CPVC solvent cement covered under Specifica-tion F 493.5. Detail Requirements5.1 Dissolving AbilityThe primer shall be capable ofdissolving at least 10 % by weight of PVC resin at 73.4 63.6F (23 6 2C) within 60 min, as specifie

13、d in 5.1. The PVCresin shall be a resin used to make poly(vinyl chloride)molding or extrusion compound meeting the requirements ofClass 12454-B, as classified in Specification D 1784.1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct respon

14、sibility of Subcommittee F17.20 on Joining.Current edition approved Sept. 10, 2002. Published October 2002. Originallypublished as F 656 80. Last previous edition F 656 96a.2Annual Book of ASTM Standards, Vol 08.01.3Annual Book of ASTM Standards, Vol 08.04.4Available from the National Sanitation Fou

15、ndation, P.O. Box 1468, Ann Arbor,MI 48106.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.2 StabilityThe 10 % resin-primer solution mixed inaccordance with 6.1.1 shall be tested for stability in accordancewith 6.2.6. Test Methods6

16、.1 Dissolving Ability:6.1.1 Weigh 270 g of the primer being tested into a closedmixing container. Weigh out 30 g of PVC resin. Adjust thetemperature of the primer to 73.4 6 3.6F (23 6 2C). Beginmixing the primer, using a laboratory mixer designed formixing flammable liquids. Add the resin to the pri

17、mer andcontinue mixing for 60 min at a mixing speed of 1500 r/min orless, using a mixing blade and speed so that the maximumtemperature of the mixture during the mixing period is 90F(32C) or less. After 60 min, turn off the mixer and adjust thetemperature to 73.4 6 3.6F (23 6 2C).6.1.2 Visually obse

18、rve whether the resin is completelydissolved. The solution shall be smooth, nongrainy, free-flowing, and shall not contain any undissolved resin.6.2 StabilityHold the resin-primer solution at 40F (5C)for 24 h and then observe that (1) the resin is still completelydissolved, (2) the solution is free

19、flowing, and (3) there are nosigns of stringiness or gelatin structure.7. Retest and Rejection7.1 If the results of any test(s) do not meet the requirementsof this specification, the test(s) shall be conducted again onlyby agreement between the purchaser and the seller. Under suchagreement, minimum

20、requirements shall not be lowered, nortests omitted, substituted, changed, or modified, nor shallspecification limits be changed. If upon retest, failure occurs,the quantity of product represented by the test(s) does not meetthe requirements of this specification.8. Report8.1 Report the following in

21、formation:8.1.1 Name of primer manufacturer,8.1.2 Lot number,8.1.3 Dissolving ability, pass or fail, and8.1.4 Stability, pass or fail.9. Container Labeling and Marking9.1 Container labeling of primer shall include the following:9.1.1 Manufacturers or suppliers name and address, trade-name or tradema

22、rk.9.1.2 This designation: “ASTM F 656.9.1.3 Function of material (Primer for PVC pipe and fit-tings. Product name shall be Primer.).9.1.4 Procedure or instructions for application and use.9.1.5 Lot number of batch on container (not on closure orlid).NOTE 2Solvent cement intended for use in the join

23、ing of potablewater piping should be evaluated and certified as safe for this purpose bya testing agency acceptable to the local health authority. The evaluationshould be in accordance with requirements for chemical extraction, taste,and odor that are no less restrictive than those included in NSF S

24、tandardNo. 14. The seal or mark of the laboratory making the evaluation shouldbe included on the container.9.1.6 End-use applications (examples: potable water, pres-sure use).9.1.7 All warnings and cautions necessitated by:9.1.7.1 Ingredients,9.1.7.2 Handling and distribution of the product,9.1.7.3

25、Intended use, and9.1.7.4 Requirements of law (such as the Federal HazardousSubstances Act). These are intended to warn those who handleor use the product against potential hazards, such as flamma-bility, toxicity, etc.NOTE 3It is recommended that the color of the contents be indicatedon the label.10

26、. Safe Handling of Primer10.1 Primers for plastic pipe are made from flammableliquids. Keep them away from all sources of ignition. Maintainventilation to reduce fire hazard and to minimize breathing ofsolvent vapors. Avoid contact of primers with skin and eyes.10.2 Refer to Practice F 402 for addit

27、ional information.11. Quality Assurance11.1 When the product is marked with this designation,F 656, the manufacturer affirms that the product was manufac-tured, inspected, sampled, and tested in accordance with thisspecification and has been found to meet the requirements ofthis specification.F65602

28、2SUPPLEMENTARY REQUIREMENTSPOTABLE WATER REQUIREMENTThis requirement applies whenever a regulatory authority or user calls for the product to be used toconvey or to be in contact with potable water.S1. Products intended for contact with potable water shallbe evaluated, tested, and certified for conf

29、ormance with ANSI/NSF Standard No. 61 or the health effects portion of NSFStandard No. 14 by an acceptable certifying organization whenrequired by the regulatory authority having jurisdiction.ASTM International takes no position respecting the validity of any patent rights asserted in connection wit

30、h any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible techn

31、ical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful considerati

32、on at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Har

33、bor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F656023