ASTM F707 F707M-1994(2006) Standard Specification for Modular Gage Boards《组合式量规板标准规范》.pdf

1、Designation: F 707/F 707M 94 (Reapproved 2006)An American National StandardStandard Specification forModular Gage Boards1This standard is issued under the fixed designation F 707/F 707M; the number immediately following the designation indicates the yearof original adoption or, in the case of revisi

2、on, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This specification c

3、overs modular gage boards formounting 89-mm (312-in.), 114-mm (412-in.), 152-mm (6-in.),and 216-mm (812-in.) dial size pressure gages and dial ther-mometers for miscellaneous shipboard applications.1.2 Gage boards ordered under this specification are suitablefor pressure gages and dial thermometers

4、with either turret orback flanged type cases and with either back or bottomconnections (see Appendix X1).1.3 Gage mounting dimensions shall be in accordance withANSI B 40.011.4 The values stated in SI units are to be regarded as thestandard. The inch-pound values given in parentheses are forinformat

5、ion only.NOTE 1Gage boards covered by this specification are those normallysupplied by the shipyard as opposed to the shipyards equipment subcon-tractor.2. Referenced Documents2.1 Other Standards:B 40.1 Gages, Pressure and Vacuum, Indicating DialTypeElastic Element2Fed Spec. TT-P-645 Primer, Paint,

6、Zinc-Chromate, AlkydType3DoD-P-15328 Primer (Wash), Pretreatment (Formula No.117 for Metals) (Metric)33. Classification3.1 Gage boards are furnished in two types as follows:3.1.1 Type IGage boards for mounting 89-mm (312-in.)and 114-mm (412-in.) dial size gages as specified in Section 5.3.1.2 Type I

7、IGage boards for mounting 152-mm (6-in.)and 216-mm (812-in.) dial size gages as specified in Section 5.3.2 Gage boards are furnished in two grades as follows:3.2.1 Grade aGage boards are to be manufactured fromcarbon steel as specified in Section 5.3.2.2 Grade bGage boards are to be manufactured fro

8、maluminum alloy as specified in Section 5.4. Ordering Information4.1 Orders for gage boards under this specification shallinclude the following information:4.1.1 Quantity (number of gage boards),4.1.2 Name of item (gage board),4.1.3 Type (Type I or Type II as specified by purchaser), see3.1.1 and 3.

9、1.2,4.1.4 Grade (Grade a or Grade b as specified by purchaser),see 3.2.1 and 3.2.2,4.1.5 Paint (as specified by purchaser), see 7.2,4.1.6 Drilling for gage mounting (as specified by pur-chaser), see 5.1.1, and4.1.7 ASTM designation and date of issue.5. Materials and Manufacture5.1 Unless otherwise s

10、pecified the gage boards shall bemanufactured from 11-gage (manufacturers standard gage)carbon steel for Grade a and 3 mm (18 in.) thick aluminumalloy for Grade b. Materials shall be capable of being bent atroom temperature through 90 in any direction to an insideradius equal to its thickness withou

11、t cracking on the outside ofthe bent portion.5.1.1 Unless otherwise specified, Type I gage boards shallbe drilled for mounting both 89-mm (312-in.) and 114-mm(412-in.) dial size gages and Type II gage boards shall bedrilled for mounting both 152-mm (6-in.) and 216-mm (812-in.) dial size gages. When

12、specified by the purchaser, drillingshall be limited to one size gage for either Type I or Type IIgage boards (see 4.1.6).1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.11 onMachinery and Piping S

13、ystems.Current edition approved Feb. 1, 2006. Published February 2006. Originallyapproved in 1981. Last previous edition approved in 2001 as F 707/F 707M 94(2001).2Available from American National Standards Institute, 25 W. 43rd St., 4thFloor, New York, NY 10036.3Available from Standardization Docum

14、ents Order Desk, Bldg. 4 Section D, 700Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.6. Dimensions and Permissible Variations6.1 The dimensions of the gage board shall not vary

15、 bymore than 0.4 mm (6164 in.) except as noted in Fig. 1 and Fig.2.7. Workmanship, Finish and Appearance7.1 The gage boards shall have a workmanlike finish free ofscale, burrs, cracks, and other defects affecting serviceability orappearance.7.2 If paint is not specified by the purchaser, Grade a gag

16、eboards shall be supplied with a coat of zinc chromate primer inaccordance with Federal Specification TT-P-645, Formula 84or equal (yellow) 0.038-mm (1.5-mils) dry film thickness.Grade b gage boards shall be supplied with one pretreatmentwash coat in accordance with Specification DOD-P-15328Formula

17、117 or equal (dark green) 0.013-mm (0.5-mils) dryfilm thickness and one coat of zinc chromate primer inaccordance with Federal Specification TT-P-645 Formula 84Dor equal (dark green) 0.013 mm (1.5-mils) dry film thickness.8. Product Marking8.1 Each shipping unit shall bear a tag or be plainly marked

18、with the following: ASTM designation number, name ortrademark of manufacturer, number of pieces, and purchaseorder number.9. Keywords9.1 dial pressure gages; dial thermometers; modular gageboards; pressure gagesFIG. 1 Gage Board Type IF 707/F 707M 94 (2006)2APPENDIX(Nonmandatory Information)X1. RATI

19、ONALE USED FOR DEVELOPMENT OF SPECIFICATION FOR MODULAR GAGE BOARDSX1.1 This specification has been developed primarily toprovide maximum versatility for the installation of 89-mm(312-in.), 114-mm (412-in.), 152-mm (6-in.), and 216-mm(812-in.) dial size simplex, duplex, and differential pressuregage

20、s and dial thermometers with either turret- or back-flangedcases (see Fig. X1.1 Fig. X1.2 Fig. X1.3).X1.2 The gage board is suitable for single-gage installation,but has the versatility of being bolted together horizontally,vertically, in pyramid fashion or a combination thereof toFIG. 2 Gage Board

21、Type IIFIG. X1.1 Bottom- and Back-Connected Pressure Gages for Horizontal Installations of Type I or Type II Gage BoardsF 707/F 707M 94 (2006)3provide for multigage installations utilizing both Type I andType II gage boards.X1.3 When used in horizontally arranged installations,either bottom or back

22、connected pressure gages and dialFIG. X1.2 Back-Connected Pressure Gages for Vertical or Combined Vertical, Horizontal, and Pyramid Arrangements of Type I or Type IIGage BoardsFIG. X1.3 Back Connected Type I and Type II Gage Boards Combined For Vertical, Horizontal, and Pyramid ArrangementsF 707/F 7

23、07M 94 (2006)4thermometers may be used. When used vertically or in com-bination with vertical, horizontal, or pyramid arrangements,back connected pressure gages and dial thermometers must beused.X1.4 This specification does not cover flush-mountedgages.ASTM International takes no position respecting

24、 the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standar

25、d is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International

26、 Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.Thi

27、s standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F 707/F 707M 94 (2006)5