ASTM F952-2003 Standard Specification for Mixing Machines Food Electric《电动食品搅拌机的标准规范》.pdf

1、Designation: F 952 03Standard Specification forMixing Machines, Food, Electric1This standard is issued under the fixed designation F 952; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parent

2、heses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This specification covers vertical electric food mixingmachines in th

3、e size range (as expressed by bowl capacity)from 5 to 140 qt. These machines shall be adaptable formixing, whipping, and beating food products. This specifica-tion does not include special purpose machines that areintended solely for mixing dough.1.2 This specification also covers optional construct

4、ionfeatures and attachments that enhance the mixing, beating, orwhipping capabilities of the machine. This specification doesnot cover ancillary equipment that can be driven by theattachment hub.1.3 The values stated in inch-pound units are to be regardedas the standard.1.4 The following precautiona

5、ry caveat pertains only to thetest methods portion, Section 9, of this specification. Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and dete

6、rmine the applicability of regulatory limita-tions prior to use.2. Referenced Documents2.1 ASTM Standards:D 3951 Practice for Commercial Packaging2F 760 Specification for Food Service Equipment Manuals3F 1166 Practice for Human Engineering Design for MarineSystems, Equipment and Facilities42.2 NSF/A

7、NSI Standards:5NSF/ANSI No. 2 Food EquipmentNSF/ANSI No. 8 Commercial Powered Food PreparationEquipmentNSF Food Equipment Listing (Current Year)2.3 Underwriters Laboratories Standards:6ANSI/UL 763 Motor-Operated Commercial Food PreparingMachinesANSI/UL 969 Marking and Labeling Systems2.4 ANSI Standa

8、rds:7Z1.4 Sampling Procedures and Tables for Inspection byAttributesS1.13 Methods for Measurement of Sound Pressure Levels2.5 Military Standards:8MIL-STD-1399/300 Interface Standard for Shipboard Sys-tems, Section 300A, Electric Power, Alternating CurrentMIL-STD-167/1 Mechanical Vibration of Shipboa

9、rd Equip-ment (Type IEnvironmental and Type IIInternallyExcited)MIL-STD-461 Requirements for the Control of Electro-magnetic Interference Characteristics of Subsystems andEquipment3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 agitators, nthese devices attach to the vertical

10、shaftthat protrudes downward from the mixer and converts theplanetary rotation into the desired action on the foodstuffswithin the bowl.3.1.2 attachment hub, nthe device that locks ancillarydevices, such as a vegetable slicer or a chopping end, into anindustry standard #12 tapered hub (#10 tapered h

11、ub for Size 5machines) and provides a rotating square drive. This ismounted above the bowl on the front of the mixer.3.1.3 bowl guard, nthe barrier, assembled over the bowlarea, intended to reduce the users access to the hazards thatexist in the bowl during machine operation.1This specification is u

12、nder the jurisdiction of ASTM Committee F26 on FoodService Equipment and is the direct responsibility of Subcommittee F26.04 onMechanical Preparation Equipment.Current edition approved Sept. 10, 2003. Published Sept. 2003. Originallyapproved in 1985. Last previous edition approved in 1999 as F 952 9

13、9.2Annual Book of ASTM Standards, Vol 15.09.3Annual Book of ASTM Standards, Vol 15.08.4Annual Book of ASTM Standards, Vol 01.07.5Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd., AnnArbor, MI 48113-0140.6Available from comm2000, 1414 Brook Dr., Downers Grove, IL 60515.7Available

14、 from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036.8Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West

15、Conshohocken, PA 19428-2959, United States.4. Classification4.1 Food mixers covered in this specification are the fol-lowing types:4.1.1 Type I, bench-mounted mixer:SizeBowlCapacity,qt,min/maxAgitator r/minMotor Horse-power Rating,minLowestSpeed,less thanHighestSpeed,greater than5 5/7 150 5001612 12

16、/15 120 3001320 20/25 120 300124.1.2 Type II, floor-mounted mixer:SizeBowlCapacity,qt,min/maxAgitator r/minMotor Horse-power Rating,minLowest Speed,less thanHighestSpeed,greater than20 20/25 120 3001230 30/36 100 3003440 40/45 100 300 11460 60/70 80 280 11280 80/90 80 280 3140 140/160 55 260 54.1.3

17、Classes:4.1.3.1 Class 1Painted finish.4.1.3.2 Class 2Nonpainted finish. All nonwearing sur-faces to be either polished aluminum, plated carbon steel, orstainless steel.5. Ordering Information5.1 Purchasers should select the mixer and any preferredoptions and include the following information in the

18、purchas-ing document:5.1.1 Title, number, and date of this specification,5.1.2 Type, size, and class of mixer required (see 4.1),5.1.3 Electrical power supply characteristics; voltage,phase, frequency (see 6.5 and 6.7),5.1.4 Bowls, agitators, accessory equipment, options, mixerguard, spare parts, an

19、d maintenance parts required,5.1.5 Labeling requirements (if different than Section 13),5.1.6 Quantity of mixers to be furnished, and5.1.7 Any special requirements or deviations from thisspecification.6. Physical Requirements6.1 Design and ManufactureThe mixer shall meet thethen current applicable r

20、equirements of NSF Standard 8 andUL 763. Accessories, such as agitators, bowl trucks, bowls,tables, extensions, adapters, splash covers, and storage standsshall meet the applicable requirements of NSF Standard 2 or 8at the time of purchase. Optional accessories, component parts,assemblies, and spare

21、 parts shall be identical to the extentnecessary to insure interchangeability between mixers.6.1.1 Compliance with NSF StandardAcceptable evi-dence of the mixer meeting the requirements of NSF Standard8 shall be the NSF listing mark on the finished product andlisting in the current edition of the NS

22、F Official Listing of FoodEquipment, or a certified test report from a recognized inde-pendent testing laboratory acceptable to the user, or a certifi-cate issued by NSF under its special one time contractevaluation/certification service.6.1.2 Compliance with UL 763Acceptable evidence ofmeeting the

23、requirements of UL 763 shall be a UL Listing markon the mixer, or a certified test report from a recognizedindependent testing laboratory acceptable to the user.6.2 Drive MechanismThe mixer shall be driven by anelectric motor, through a reduction system, to the planetary/beater shaft system. The ent

24、ire drive system shall be enclosedwithin the mixer itself. All constituent active parts within thedrive system shall be replaceable. All mixers shall be equippedwith an internal clutch, shock absorber, or belt drive tominimize the shock of starting or shifting gears of the mixer.Size 60 and larger g

25、ear drive speed selection mixers shall beequipped with a shift interlock switch that will automaticallydisconnect power to the main drive motor if the operatorattempts to shift speeds without first shutting off the motor.6.3 Speed SelectorA speed selector shall be provided tochange agitator speed. E

26、ither continuously variable or discretespeed selection is acceptable. A means to provide the user withreference marks for speed repeatability is required. In no caseshall less than three distinct speeds be available on gear boxequipped mixers or three distinct markings be available oncontinuously va

27、riable transmissions.6.4 Beater ShaftThe beater shaft shall be verticallymounted and shall be held securely in place. Agitators shall fitsecurely and shall be capable of being removed or replacedwithout tools. The beater shaft shall be connected to planetarygearing to provide two separate rotating m

28、otions of the agitatorsimultaneously.6.5 Motor(s)Minimum horsepower rating for the maindrive motor of the mixer shall meet the requirements of 4.1.1or 4.1.2, as appropriate. If an auxiliary motor is used to performanother function (such as, bowl lifts), it shall be internallyinterconnected within th

29、e mixer to provide a single electricalpoint connection. Size 5 through 30 mixers shall be availablefor operation on a 120/60/1 line. Size 60 and larger mixers shallbe available for operation on a 208/60/3 line. Other voltageavailabilities are at the discretion of the manufacturer. Mixerswith three p

30、hase motors shall be provided with a plate, label, ordecal showing the direction of rotation. In all cases, the maindrive motor shall be rated for continuous duty.6.6 Power SupplyThe mixer may either be provided witha power supply cord or designed for permanent electricalconnection. Power supply cor

31、ds shall be a minimum 5-ft lengthand provided with a grounding type attachment plug. Mixerhousings designed for permanent electrical connection shall beprovided with an appropriate hole sized for conduit connection.6.7 Electrical SpecificationsNominal electrical specifica-tions are as follows: 120/6

32、0/1, 208/60/1, 240/60/1, 208/60/3,240/60/3, and 480/60/3.6.8 Mixing BowlsBowls shall meet the requirements ofNSF Standard 8 or NSF Criteria C-2. Bowl requirementsshould be stated in the purchasing document. The bowl shall beequipped with two handles. If the bowl is metallic, theminimum wall thicknes

33、s for bowls of 60-qt capacity or less is0.0625 in. For bowls of larger than 60-qt capacity, theminimum metallic thickness is 0.0781 in. The minimumF952032thickness at any point of the bowl after forming shall be no lessthan 0.050 in. for bowls of 60 qt or less capacity and not lessthan 0.062 in. for

34、 bowls over 60-qt capacity. All bowls shall beequipped with a durable metallic means of attachment to thebowl yoke. Bowls of 60-qt capacity or greater shall bereinforced at the points of attachment to the bowl yoke. Bowlsof nonmetallic construction shall have equivalent durability tometallic bowls.

35、Acceptable metal bowls will be either tin-plated carbon steel or stainless steel.6.9 AgitatorsMixers meeting this specification must beavailable with batter beater, sweet dough beater, dough hook,pastry knife, wing whip, and wire whip suitable for use withthe bowl size(s) specified. Stainless steel

36、must be used on thewires of whips.6.10 Bowl LiftThe mixer shall be provided with a mecha-nism for raising and lowering the bowl. Mixers of 80-qtcapacity or more shall be equipped with a powered bowl lift ifspecified in the purchase document. Size 60 and smaller mixersshall have a manually operated l

37、ift mechanism with a positivestop at the extremities of the travel. In all cases, a stop shall beprovided to prevent the agitator from contacting the bowl whenproper bowls and agitators are used together.6.11 Bowl SupportThe bowl support shall have three lugpositions matching lugs on the bowl. All m

38、ixers shall have apositive bowl locking mechanism to prevent bowl motionunder heavy loads.6.12 BaseThe base shall be constructed of materials thatare consistent with the need for rigidity and durability. For Size12 and larger machines, means shall be provided for bolting themixer to a stand (Type I)

39、 or to the floor (Type II).6.13 TimerSize 60 and larger mixers shall be providedwith a 15-min timer. The timer shall stop the mixer drive motorupon operating for the preset time. The timer or mixer designshall include an override position to permit continuous opera-tion. Mixers less than size 60 sha

40、ll be available with anoptional timer to provide the functions stated above.6.14 Attachment HubSize 60 and smaller mixers shall beprovided with an attachment hub for operating vegetable andcheese slicing, meat chopping, dicing, or equivalent attach-ments. This attachment hub shall be capable of at l

41、east 350rpm. This requirement can be met by the manufacturer with anancillary speed increaser attachment of aluminum construction.6.15 Bowl TruckType II mixers shall have optionallyavailable a bowl truck whose use is compatible with the basedesign of the mixer. The bowl truck shall be durably con-st

42、ructed and designed to hold the bowl above the point ofattachment to the bowl support when the support is at its lowestposition.6.16 Other Optional Equipment:6.16.1 Mixing Bowl ExtensionShall be optionally avail-able for size 60 and 80 mixers and made of the same materialas the bowl.6.16.2 Colander

43、and Sieve SetShall be optionally avail-able for size 20 and 30 mixers.6.16.3 Bowl AdaptersSize 20 and larger mixers shall beoptionally available with bowl adapters to use the next smallersize bowl and agitators.6.16.4 Splash CoversShall be optionally available for size60 and larger mixers.6.16.5 Tab

44、leShall be optionally available for Type I, Size20. When specified, the table shall be 24 in. high with ahorizontal surface of 30 by 24 in. A full-size shelf under the topsurface shall be provided for ancillary equipment storage. Itshall be of stainless steel construction, able to support a load of2

45、50 lb.6.17 LubricationAll wearing parts of the mixer shall beprovided with a means for lubrication or be permanentlylubricated and sealed. Oil seals shall contain the lubricant. Gearhousings shall have provisions for lubrication and shall allowlubricant to circulate around gears if applicable.6.18 F

46、inishingAll exterior surfaces of the mixer andattachments described within this specification shall be finishedto the requirements of NSF Standard 8. All sand cast parts shallbe ground smooth and, if manufactured of corroding materials,painted, or otherwise finished with a noncorroding treatment.6.1

47、9 WorkmanshipAll components and assemblies of themixer shall be free of dirt and other extraneous materials, burrs,slivers, tool and grind marks, dents, and cracks. Castings,molded parts, and stampings shall be free of voids, sand pits,blow holes, and sprues. External surfaces shall be free of sharp

48、edges and corners. All sheet metals used in the fabrication ofthe mixing machine shall be free from kinks and unspecifieddents. Forming and welding shall not cause damage to themetal and shall be done neatly and accurately. Corners shall besquare and true and all bends of a major nature shall be ofu

49、niform size and shape.6.20 Hazard Protection:6.20.1 The mixer shall meet the requirements of UL 763.6.20.2 Switch GuardThe ON/OFF control shall beguarded or fabricated in such a manner as to prevent unplannedactivation.6.20.3 Controls LocationThe controls for the mixer shallbe located such that they are easily visible and easily manipu-lated by the operator when standing in a comfortable operatingposition.6.20.4 Mixer GuardA barrier over the bowl area of themixer may be provided. The barrier may be solid or con-structed of a welded grid made of