ASTM F2448-2004(2007) Standard Practice for Manufacturer Quality Assurance System for Weight-Shift-Control Aircraft《重量转移控制飞行器用生产商质量保证体系的标准实施规程》.pdf

1、Designation: F 2448 04 (Reapproved 2007)Standard Practice forManufacturer Quality Assurance System for Weight-Shift-Control Aircraft1This standard is issued under the fixed designation F 2448; the number immediately following the designation indicates the year oforiginal adoption or, in the case of

2、revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers minimum requirements for a qual-ity assurance program for weight-shift-con

3、trol aircraft.1.2 This practice applies to weight-shift-control aircraftseeking civil aviation authority approval, in the form of flightcertificates, flight permits, or other like documentation.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use.

4、It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Significance and Use2.1 The purpose of this practice is to provide the minimumrequirements necessary for the establish

5、ment of a writtenquality assurance program for a light sport aircraft manufac-turer, or component supplier.2.2 If final assembly is completed outside of the mainproduction facility, the manufacturer shall specify the requiredprocedures and what persons are authorized to perform them.3. Materials and

6、 Manufacture3.1 Drawing Control ProcedureA written procedure shallbe in effect so that appropriate manufacturing drawings, theirmanufacturing revisions, and related documents are utilized foreach project.3.2 Component Control Procedure:3.2.1 A written procedure shall be in effect so that materials,p

7、rocesses, and components, including raw materials, are inaccordance with the manufacturing specifications.3.2.2 This procedure shall provide the purchasing agentwith all of the information required to order appropriatematerial.3.2.3 A written receiving procedure shall be in effect so thatincoming ma

8、terial and components are checked against thepurchasing specifications.3.2.4 A written procedure shall be in effect so that materialin stock can be properly identified for future use.3.2.5 Documentation on any material, process, or compo-nents certified shall be filed for reference.4. Inspection4.1

9、A written procedure shall be in effect so that appropriateinspections are made on manufactured parts and subassembliesfor conformance with engineering specifications.4.2 A written procedure shall be in effect so that appropriateinspections are made on purchased components.4.3 A written procedure sha

10、ll be in effect so that completedunits are inspected prior to delivery.4.4 Nonconforming components shall be identified andevaluated for disposition as follows:4.4.1 A component not suitable for use shall be altered ordisposed of to avoid accidental use.4.4.2 Reworked components shall be re-inspecte

11、d in accor-dance with 4.1, 4.2,or4.3 of this practice prior to use.4.4.3 In some cases, a component may be determined to beacceptable as is or as modified after further evaluation. In suchcases, appropriate review, acceptance, and documentation shallbe a requirement.4.5 AuditsA written procedure sha

12、ll be in effect to per-form audits of the quality assurance program at least onceevery two years.5. Keywords5.1 light sport aircraft; special airworthiness certificate;weight-shift-control aircraft1This practice is under the jurisdiction of ASTM Committee F37 on Light SportAircraft and is the direct

13、 responsibility of Subcommittee F37.40 on Weight Shift.Current edition approved Feb. 15, 2007. Published July 2007. Originallyapproved in 2004. Last previous edition approved in 2004 as F 2448 04.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, Uni

14、ted States.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such

15、rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additio

16、nal standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the A

17、STM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F 2448 04 (2007)2