BHMA A156 26-2017 CONTINUOUS HINGES.pdf

1、 1 ANSI/BHMA A156.26-2017 Revision of BHMA A156.26-2012 STANDARD FOR CONTINUOUS HINGES SPONSOR BUILDERS HARDWARE MANUFACTURERS ASSOCIATION, INC. Approved by the AMERICAN NATIONAL STANDARDS INSTITUTE December 22, 2017 2 AMERICAN NATIONAL STANDARD An American National Standard implies a consensus of t

2、hose substantially concerned with its scope and provisions. An American National Standard is intended as a guide to aid the manufacturer, the consumer and the general public. The existence of an American National Standard does not in any respect preclude anyone, whether he has approved the Standard

3、or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the Standard. American National Standards are subject to periodic review and users are cautioned to obtain the latest editions. CAUTION NOTICE: This American National Standard is permitte

4、d to be revised or withdrawn at any time. The procedures of the American National Standards Institute require that action be taken to reaffirm, revise, or withdraw this Standard no later than five years from the date of publication. Purchasers of American National Standards receive current informati

5、on on all Standards by calling or writing The American National Standards Institute. Published by BUILDERS HARDWARE MANUFACTURERS ASSOCIATION, INC. 355 Lexington Avenue New York, New York 10017 Copyright 2017 by the Builders Hardware Manufacturers Association, Inc. Not to be reproduced without spec

6、ific authorization from BHMA Printed in the USA This Standard was developed by the Builders Hardware Manufacturers Association, Inc. It was approved by ANSI under the canvass method. BHMA was accredited on 21 March 1983 as a sponsor using the Canvass Method. 3 FOREWORD (This Foreword is not a part o

7、f ANSI/BHMA A156.26) The general classification of builders hardware includes a wide variety of items which are divided into several categories. To recognize this diversity, a sectional classification system has been established. Continuous Hinges is one such section and this Standard is a result of

8、 the collective efforts of members of the Builders Hardware Manufacturers Association, Inc. who manufacture these products. The total Product Standards effort is, therefore, a collection of sections, each covering a specific category of items. Performance tests and, where necessary, dimensional requ

9、irements have been established to insure a degree of safety and stability. There are no restrictions on design except for those dimensional requirements imposed. This Standard is not intended to obstruct but rather to encourage the development of improved products, methods and materials. The BHMA re

10、cognizes that errors will be found, items will become obsolete, and new products, methods and materials will be developed. With this in mind, the Association plans to update, correct and revise these Standards on a regular basis. It shall also be the responsibility of manufacturers to request such a

11、ppropriate revisions. 4 TABLE OF CONTENTS Section Page 1. Scope . 5 2. Definitions 5 3. General 6 4. Test Equipment . 7 5. Test Procedures . 7 6. Tests 8 Appendix A full door also acceptable 6.10 Salt Spray Test Finish Test specimens shall not have corrosion exceeding the values given below when tes

12、ted in accordance with ANSI/BHMA A156.18. Requirements Clear Coatings on single plated ferrous material All Grades: 24 Hours Painted material All Grades: 48 Hours Non-Ferrous material - plated or unplated, coated or uncoated All Grades: 72 Hours Stainless steel All Grades: 200 Hours 10 7. EXPLANATIO

13、N OF NUMBERING SYSTEM 7.1 First letter denotes BHMA Product Section (A) First numeral indicates general type of material used: 1-Brass, Bronze 5-Stainless Steel, 300 Series 3-Aluminum 8-Steel Second numeral identifies type of product: 1-Edge Mounted Hinges 3-Full Surface Hinges 2-Half Edge Mounted H

14、inges 4-Half Surface Hinges 5-Swing Clear 6-Raised Barrel 7-Wide Throw 0-Other Third numeral denotes electrical modifications: 0-None 2-Monitor 1-Concealed Wire Transfer 3-Power Transfer 4-Other 5-Power over Ethernet (PoE) Fourth numeral denotes grade classification door weight (lbs) : 1-150 3-600 2

15、-300 4-1200 Fifth numeral designates the grade classification of the item: 1 - Grade 1 3 - Grade 3 2 - Grade 2 Second letter denotes hinge type B-Barrel G-Geared 7.2 Example: A13021B A: Section A 1: Brass/bronze material 3: Full surface hinges 0: No electrical modifications 2: For use on doors weigh

16、ing over 150 lbs. up to 300 lbs. 1: Grade 1 B: Barrel hinge Specify other options as applicable (See 3.5) 11 8. PRODUCT TYPE ILLUSTRATIONS BARREL TYPE HINGE EDGE MOUNT GEAR TYPE HINGE EDGE MOUNT BARREL TYPE HINGE HALF SURFACE GEAR TYPE HINGE HALF SURFACE BARREL TYPE - HALF EDGE MOUNT GEAR TYPE HINGE

17、 - HALF EDGE MOUNT 12 BARREL TYPE HINGE-HALF SURFACE IN. OFFSET RAISED BARREL TYPE HINGE BARREL TYPE HINGE FULL SURFACE GEAR TYPE HINGE FULL SURFACE BARREL TYPE-SWING CLEAR GEARED TYPE HINGE-SWING CLEAR 13 APPENDIX A - (NOT A PART OF ANSI/BHMA A156.26) A-1 CONFORMANCE CRITERIA Certification that pro

18、ducts offered meet the requirements of this Standard and conform to individual manufacturers drawings, specifications, standards and quality assurance practices are available and in some circumstances are required. Buyer requirements determine the need for proof of conformance such as first article

19、inspection, test laboratory reports or listings. Specifiers requiring assertions of conformance utilize statements of conformance by individual manufacturers, or test reports acceptable to the buyer. A-2 PRESERVATION, PACKAGING, AND PACKING Unless other arrangements between buyer and seller are made

20、, preservation, packaging and packing shall be sufficient to protect containers and their contents under normal shipping and handling conditions from the source of supply to the destination point. A-3 MARKING Unless other arrangements between buyer and seller are made, marking shall be in accordance

21、 with the individual manufacturers standard practice. APPENDIX B - (NOT A PART OF ANSI/BHMA A156.26) Definitions of Terms not used in this Standard but common in the Industry. B-1 Bearings A separate component made of anti-friction material placed between the hinge load bearing surfaces. B-2 End Pla

22、y The amount of axial movement along the pin between the leaves. B-3 Knuckle Length The nominal dimension of the knuckle measured parallel to the pin. B-4 Paint Clearance The minimum dimension between the outer face of the knuckle and the opposing edge of the leaf cutout over the entire range of the

23、 pivotal movement of the hinge. B-5 Pin Retention The manner in which the pin is retained in the hinge including being spun, staked, or welded. B-6 Side Play The amount of movement of the leaves perpendicular to the pin. B-7 Width The overall dimension of the leaves measured perpendicular to the pin

24、 when in an open position (180 degrees). APPENDIX C - (NOT A PART OF ANSI/BHMA A156.26) Grade ratings for continuous hinges are valid for the range of door weights specified in the listing. Example: Grade X-150 Grade X for use on doors from 0 lbs. (0 kg.) - 150 lbs. (68 kg.) Grade X-300 Grade X for

25、use on doors from 150 lbs. (68 kg.) - 300 lbs. (135 kg.) Grade X-600 Grade X for use on doors from 300 lbs. (135 kg.) - 600 lbs. (270 kg.) Grade X-1200 Grade X for use on doors from 600 lbs. (270 kg.) - 1200 lbs. (540 kg.) 14 Figure 1: Gage Block Method for Measuring Vertical Wear Figure 2: Standard Method for Measuring Lateral Wear (View: Facing the Door) Figure 3: Cycle Test Fixture 15