BS 1853-2-1995 Tubular fluorescent lamps for general lighting service - Specification for lamps used in the United Kingdom not included in BS EN 60081 BS EN 60901 BS EN 61195 and B.pdf

1、BRITISH STANDARD BS1853-2: 1995 Specification for Fluorescent lamps for general lighting service Part 2: Specification for lamps used in the United Kingdom not included in BSEN60081, BSEN60901, BSEN61195 and BSEN61199BS1853-2:1995 This British Standard, having been prepared under the directionof the

2、 Electrical SectorBoard, was published underthe authority of the Standards Board and comes intoeffect on 15 December1995 BSI 07-1999 First published April 1952 Second edition September 1956 Third edition November 1960 Fourth edition February 1967 Fifth edition June 1974 Sixth edition August 1979 Sev

3、enth edition December 1995 The following BSI references relate to the work on this standard: Committee reference CPL/34/1 Draft for comment94/2203612DC ISBN 0 580 24729 5 Committees responsible for this British Standard The preparation of this British Standard was entrusted by Technical Committee CP

4、L/34, Lamps and related equipment, to Subcommittee CPL/34/1, Electric lamps, upon which the following bodies were represented: British Lighting Association for the Preparation of Standards (BRITLAPS) Chartered Institution of Building Services Engineers Electricity Association Engineering Equipment a

5、nd Materials Users Association Institution of Lighting Engineers Lighting Industry Federation Ltd. London Regional Transport National Illumination Committee of Great Britain Society of Motor Manufacturers and Traders Ltd. The following bodies were also represented in the drafting of the standard thr

6、ough subcommittees: British Sign Association Consumer Policy Committee of BSI Department of Transport Amendments issued since publication Amd. No. Date CommentsBS1853-2:1995 BSI 07-1999 i Contents Page Committees responsible Inside front cover Foreword ii Section 1. General 1.1 Scope 1 1.2 Reference

7、s 1 1.3 Definitions 1 1.4 Lamp specifications 1 1.5 Sampling 1 1.6 Marking, mechanical, physical and starting characteristics 1 1.7 Requirements and conditions of test for electrical and luminous characteristics and for life 1 1.8 Conditions of conformity 1 Section 2. Lamp data sheets 2.1 Principles

8、 of layout of data sheets 3 2.2 List of specific lamp types included in this standard 3 Figure 1 Diagrammatic drawing for location of lamp dimensions for U-shaped lamps with G13 caps 2 List of references Inside back coverBS1853-2:1995 ii BSI 07-1999 Foreword This New Edition has been prepared by Sub

9、committee CPL/34/1. Following the publication of BSEN60081, BSEN60901, BSEN61195 and BSEN61199, this new edition of BS1853-2 has been published to take into account the lamps, included in the previous edition, which are not covered by those European standards. It supersedes BS1853-2:1979 which is wi

10、thdrawn. BS1853-1:1990 has been superseded by BSEN60081:1994. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity fro

11、m legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 to10, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment

12、table on the inside front cover.BS1853-2:1995 BSI 07-1999 1 Section 1. General 1.1 Scope This British Standard is applicable to those fluorescent lamps which are used in the United Kingdom and which are not specified in BS EN60081:1994, BS EN60901:1994, BS EN61195:1994 or BSEN61199:1994. It specifie

13、s the characteristics of fluorescent lamps for general lighting service, which have pre-heated cathodes and which operate from50 Hz a.c. mains with or without the aid of a starter and in association with ballasts conforming to BS EN60920:1991 and BSEN60921:1991. 1.2 References 1.2.1 Normative refere

14、nces This British Standard incorporates, by dated or undated reference, provisions from specific editions of other publications. These normative references are made at the appropriate places in the text and the cited publications are listed on the inside back cover. For dated references, only the ed

15、ition cited applies; any subsequent amendments to, or revisions of, any of the cited publication apply to this British Standard only when incorporated in the reference by updating or revision. For undated references, the latest edition of the cited publication applies, together with any amendments.

16、1.2.2 Informative references This British Standard refers to other publications that provide information or guidance. Editions of these publications current at the time of issue of this standard are listed on the inside back cover, but reference should be made to the latest editions. 1.3 Definitions

17、 For the purposes of this Part of BS1853, the definitions given in BS EN60081:1994, BS EN60901:1994, BS EN61195:1994 and BS EN61199:1994 apply. 1.4 Lamp specifications Each lamp shall conform to the requirements given on the appropriate lamp data sheet. The lamp dimensions to be controlled shall be

18、as illustrated for circular lamps on sheet901-IEC-3004-1 of BSEN60901:1994 and for U-shaped lamps in Figure 1 of this standard. 1.5 Sampling The method of selection and the test quantities specified in BS EN60081:1994, BS EN60901:1994, BSEN61195:1994 and BS EN61199:1994 shall apply, as appropriate.

19、1.6 Marking, mechanical, physical and starting characteristics Lamp marking, dimensions and starting characteristics specified in BS EN60081:1994, BSEN60901:1994, BS EN61195:1994 and BSEN61199:1994 shall apply, as appropriate. 1.7 Requirements and conditions of test for electrical and luminous chara

20、cteristics and for life The requirements and conditions of test specified in BS EN60081:1994, BS EN60901:1994, BSEN61195:1994 and BS EN61199:1994 shall apply, as appropriate. 1.8 Conditions of conformity The conditions of conformity set out in BS EN60081:1994, BS EN60901:1994, BS EN61195:1994 and BS

21、EN61199:1994 shall apply, as appropriate. The test methods, ballasts, starters and torsion test holders described in the annexes of BS EN60081:1994, BS EN60901:1994, BS EN61195:1994 and BSEN61199:1994 shall apply, as appropriate.BS1853-2:1995 2 BSI 07-1999 NOTEThis drawing is intended only to indica

22、te dimensions to be controlled and is to be used in conjunction with the relevant lamp standard sheets. Figure 1 Diagrammatic drawing for location of lamp dimensions for U-shaped lampswithG13 caps a a Data sheet7004-51 of BS5101-1:1975BS1853-2:1995 BSI 07-1999 3 Section 2. Lamp data sheets 2.1 Princ

23、iples of layout of data sheets The numbering system for lamp data sheets is as follows: The first number represents the number of this publication “1853”. The second number represents the lamp data sheet number. The third number represents the edition of the page of the data sheet. In cases where a

24、data sheet has more than one page it is possible for the pages to have different edition numbers with the data sheet number remaining the same. 2.2 List of specific lamp types included in this standard Sheet number Lamp rating Cap Method of starting Cathode type 1853-02 40 W G13 Starter Pre-heated 1

25、853-20 60 W G10q Starter Pre-heated 1853-40 50 W G13 Starterless Pre-heated High-cathode resistanceBS1853-2:1995 4 BSI 07-1999 U-shaped fluorescent data sheet Page1/2 Nominal dimensions Cap Rating Starting 525mm 120mm G13 40W With starter Mechanical, physical and starting requirementsFor lamp markin

26、g, tubes, dimensions, starting requirements and conditions of conformity the appropriate requirements of BS EN60081:1994 and/or BS EN61195:1994 apply. Lamp dimensions (see Figure 1) A B C D Maximum Minimum Maximum Maximum Minimum Maximum mm mm mm mm mm mm 524.0 516.0 120.66 94.0 90.0 26.66 Lamp star

27、ting test Test voltage Ballast voltage rating V V 180 220 Initial readings and colour For lamp voltage, wattage, luminous characteristics and conditions of conformity, the requirements ofBS EN60081 apply. Lamp electrical characteristics Frequency Rated wattage Objective wattage Voltage (r.m.s.) at l

28、amp terminals Nominal current Objective Max. Min. Running Pr-heat Hz W W V V V A A 50 40 39 112 122 102 0.42 0.55 60 Luminous and colour characteristics Minimum rated luminous flux Chromaticity co-ordinates Colour 1 2 3 Daylight Full white Warm white x y x y x y lm lm lm 2600 0.432 0.403 1853 02 01B

29、S1853-2:1995 BSI 07-1999 5 U-shaped fluorescent lamp data sheet Page2/2 Life test For life test and conditions of conformity the requirements of BS EN60081:1994 apply. Minimum lumen maintenance 2000h 70 % life 80 % 70 % Ballast The requirements of BS EN60921:1991 apply. Reference ballast characteris

30、tics Frequency Rated wattage Rated voltage Calibration current Voltage/current ratio Power factor Hz W v A 7 50 40 220 0.43 390 0.10 60 Information for ballast design Open circuit voltage Pre-heating current Max. (r.m.s.) voltage across starter terminals with lamp operating Equivalent resistance of

31、both cathodes in series Min. (r.m.s.) at starter Max. (peak) at lamp Min. Max. V V A A V 7 180 400 0.387 0.904 134 20 Information for starter design Non-reclosure voltage Minimum pulse voltage V V 140 400 1853 02 01BS1853-2:1995 6 BSI 07-1999 Circular fluorescent lamp data sheet Page1/2 Nominal dime

32、nsions Cap Rating Starting 406mm G10q 60 W With starter Mechanical, physical and starting requirements For lamp marking, tubes, dimensions, starting and conditions of conformity, the appropriate requirements of BS EN60901:1994 and/or BS EN61199:1994 apply. Lamp dimensions (see sheet901-IEC-3004-1 of

33、 BS EN60901:1994) A B C and D D 1 Max. Min. Max. Min. Max. Min. Max. Min. mm mm mm mm mm mm mm mm 347.7 341.3 347.7 338.1 412.8 400.0 34.1 29.4 Lamp starting test Test voltage Ballast voltage rating V V 180 220 Initial readings and colour For lamp voltage, wattage, luminous characteristics and condi

34、tions of conformity, the requirements ofBS EN60901 apply. Lamp electrical characteristics Frequency Rated wattage Objective wattage Voltage (r.m.s.) at lamp terminals Nominal current Objective Max Min. Running Pre-heat Hz W W V V V A A 50 60 58.0 92 102 82 0.750 1.150 60 60 Luminous and colour chara

35、cteristics Minimum rated luminous flux Chromaticity co-ordinates Colour 1 2 3 Daylight Full white Warm white x y x y x y lm lm lm 3000 3400 3500 0.309 0.327 0.368 0.371 0.435 0.402 185320 01BS1853-2:1995 BSI 07-1999 7 Circular fluorescent lamp data sheet Page2/2 Life test For life test, the requirem

36、ents of BS EN60901:1994 apply. Minimum lumen maintenance 2000h 70 % life 75 % 60 % Ballast The requirements of BS EN60920:1991 and BS EN60921:1991 apply. Reference ballast characteristics Frequency Rated wattage Rated voltage Calibration current Voltage/current ratio Power factor Hz W V A 7 50 65 22

37、0 0.67 240 0.10 60 Information for ballast design Open circuit voltage Pre-heating current Max. (r.m.s.) voltage across starter terminals with lamp operating Equivalent resistance of both cathodes in series Min. (r.m.s.) at starter Max. (peak) at lamp Min. Max. V V A A V 7 180 400 0.603 1.410 132 25

38、 Information for starter design Non-enclosure Minimum pulse voltage V V 130 400 1853 20 01BS1853-2:1995 8 BSI 07-1999 Linear Fluorescent lamp data sheet Page1/2 Nominal dimensions Cap Rating Starting Cathode 1500mm 25mm G13 50 W Starterless High resistance Mechanical, physical and starting requireme

39、nts For lamp marking, tubes, dimensions, starting requirements and conditions of conformity, BSEN60081:1994 and BS EN61195:1994 apply. Lamp dimensions (see sheet81-IEC-0001-1 of BS EN60081:1994) A B C D Max. Max. Min. Max. Max. mm mm mm mm mm 1500 1507.1 1504.7 1514.2 28.0 Lamp starting test Open ci

40、rcuit voltage at lamp terminals for starting test Ballast rating for starting test Wattage Voltage V W V 270 50 240 Initial readings and colour For lamp voltage and wattage, luminous characteristics, cathode characteristics, and conditions ofconformity, the requirements of BS EN60081:1994 apply. Lam

41、p electrical characteristics Frequency Rated wattage Objective wattage Voltage (r.m.s.) at lamp terminals Nominal running current Objective Max. Min. Hz W W V V V A 50 50 48 155 170 140 0.37 60 Luminous and colour characteristics Minimum rated luminous flux Chromaticity co-ordinates Colour 1 2 3 Day

42、light Full white Warm white x y x y x y lm lm lm 3000 3250 0.365 0.373 0.432 0.403 1853 40 01BS1853-2:1995 BSI 07-1999 9 Linear Fluorescent lamp data sheet Page2/2 Cathode characteristics Cathode Test voltage Resistance of each cathode 7 7 V Objective Min. High resistance 8 19 Life test For life tes

43、t and conditions of conformity the requirements of BS EN60081:1994 apply. Minimum lumen maintenance 2000h 70 % life 80 % 70 % Ballast The requirements of BS EN60920:1991 and BS EN60291:1991 apply. Reference ballast characteristics Frequency Rated wattage Rated voltage Calibration current Voltage/cur

44、rent ratio Power factor Hz W W A 7 50 50 350 0.37 735 0.12 60 Information for ballast design Open circuit voltage at lamp terminals Maximum current in any lead to cathode Pre-heat cathode voltage Min. (r.m.s.) Max. (peak) Min. Max. V V A V V 270 580 0.63 6.5 11.0 1853 40 0110 blankBS1853-2:1995 BSI

45、07-1999 List of references Normative references BSI Standards Publications BRITISH STANDARDS INSTITUTION, London BS EN60081:1994, Specification for tubular fluorescent lamps for general lighting service. BS EN60901:1994, Specification for single-capped fluorescent lamps. Safety and performance requi

46、rements. BS EN60920:1991, Specification for ballasts for tubular fluorescent lamps. General and safety requirements. BS EN60921:1991, Specification for ballasts for tubular fluorescent lamps. Performance requirements. BS EN61195:1994, Double-capped fluorescent lamps. Safety specifications. BS EN6119

47、9:1994, Single-capped fluorescent lamps. Safety specifications. BS1853-2: 1995 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the internatio

48、nal level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would

49、 be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign