BS 2C 19-1994 Specification for pressure re-oiling connection (new type)《新型压力重上油连接器规范》.pdf

1、BRITISH STANDARD AEROSPACE SERIES BS 2C 19:1994 ISO 9939:1994 (superseding BSC19:1986) Specification for Pressure re-oiling connection (new type)BS2C 19:1994 This British Standard, having been prepared under the directionof the Aerospace Standards Policy Committee, waspublished under the authorityof

2、 the Standards Boardand comes into effect on 15September 1994 BSI 08-1999 The following BSI references relate to the work on this standard: Committee reference ACE/14 Draft for comment 90/70673 DC ISBN 0 580 23212 3 Committees responsible for this British Standard The preparation of this British Sta

3、ndard was entrusted by the Aerospace Standards Policy Committee (ACE/-) to Technical Committee ACE/14, upon which the following bodies were represented: Civil Aviation Authority (Airworthiness Division) Institute of Petroleum Ministry of Defence Society of British Aerospace Companies Limited Amendme

4、nts issued since publication Amd. No. Date CommentsBS2C19:1994 BSI 08-1999 i Contents Page Committees responsible Inside front cover National foreword ii 1 Scope 1 2 Requirements 1 Annex A (informative) Bibliography 3 Figure 1 2 Table 1 1BS2C 19:1994 ii BSI 08-1999 National foreword This British Sta

5、ndard has been prepared under the direction of the Aerospace Standards Policy Committee. It is identical with ISO 9939:1994, Aerospace Pressure re-oiling connection (new type), published by the International Organization for Standardization (ISO). This standard is a new edition ofBS C 19:1986, which

6、 is withdrawn, and it has been published to adoptISO9939 which itself is the international adoption of BSC 19:1986. There is, therefore, no technical difference between BS C 19 and BS 2C 19. The standard provides requirements for new designs of equipment. Previous designs still in service are covere

7、d by BS C3:1964 (obsolescent) and ISO451:1976. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligat

8、ions. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 to3 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS2C19

9、:1994 BSI 08-1999 1 1 Scope This International Standard specifies the basic dimensions of a pressure re-oiling connection for use with all oils for aircraft engines, and the clearance envelope to be provided. 2 Requirements 2.1 Connection The connection shall conform to the minimum requirements and

10、basic dimensions given in Figure 1 and Table 1. 2.2 Access clearance The minimum dimensions of the access clearance envelope to be provided around the connection shall be as given in Figure 1 and Table 1. Table 1 Dimension Millimetres Inches min. max. min. max. A B C D E F G H J K L M P r 1 r 2 r 3

11、14,73 25,35 30,66 17,4 2,54 5,56 127 76,2 4,62 2,92 31,75 0,13 2,92 0,51 14,78 25,40 30,96 17,5 2,59 6,35 44,45 4,88 3,43 0,025 0,25 3,43 0,76 0,580 0,998 1,207 0,685 0,100 0,219 5 3 0,182 0,115 1,25 0,005 0,115 0,02 0,582 1,000 1,219 0,689 0,102 0,250 1,75 0,192 0,135 0,001 0,010 0,135 0,03BS2C 19:

12、1994 2 BSI 08-1999 NOTE 1Remove all burrs and break sharp edges 0,4 mm (0,016 in) max. radius. NOTE 2The method of indicating geometric tolerances complies with ISO 1101. NOTE 3The method of indicating surface texture complies with ISO 1302. Figure 1 BS2C19:1994 BSI 08-1999 3 Annex A (informative) B

13、ibliography 1 ISO 1101:1983, Technical drawings Geometrical tolerancing Tolerances of form, orientation, location and run-out Generalities, definitions, symbols, indications on drawings. 2 ISO 1302:1992, Technical drawings Method of indicating surface texture.BS 2C 19:1994 ISO 9939:1994 BSI 389 Chis

14、wick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by a

15、mendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard

16、would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of

17、 standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been p

18、ublished as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also availabl

19、e which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other ben

20、efits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationalstandardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1

21、988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details

22、such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.