BS 4215-15-1990 Resistance spot welding electrodes electrode holders and ancillary equipment - Specification for insulated pins for use in electrode back-ups《电阻点焊电极 焊钳和辅助设备 第15部分 电.pdf

1、BRITISH STANDARD BS4215-15: 1990 Incorporating Amendment No.1 Resistance spot welding electrodes, electrode holders and ancillary equipment Part15: Specification for insulated pins for use in electrode back-upsBS4215-15:1990 This British Standard, having been prepared under the directionof the Weldi

2、ng Standards Policy Committee, waspublished under the authorityof the Board of BSI andcomes into effect on 31December1990 BSI10-1999 The following BSI references relate to the work on this standard: Committee reference WEE/26 Draft for comment89/70856 DC ISBN 0 580 19095 1 Committees responsible for

3、 this British Standard The preparation of this British Standard was entrusted by the Welding Standards Policy Committee (WEE/-) to Technical Committee WEE/26, upon which the following bodies were represented: Association of Supervisory and Executive Engineers British Non-ferrous Metals Federation Br

4、itish Steel Industry Copper Development Association Electricity Supply Industry in England and Wales Health and Safety Executive Society of British Aerospace Companies Ltd. Society of Motor Manufacturers and Traders Ltd. Welding Institute Welding Manufacturers Association (BEAMA Ltd.) Coopted member

5、s Amendments issued since publication Amd. No. Date Comments 7132 July 1992 Indicated by a sideline in the marginBS4215-15:1990 BSI 10-1999 i Contents Page Committees responsible Inside front cover Foreword ii 1 Scope 1 2 References 1 3 Dimensions 1 4 Designation 1 5 Material 1 6 Finish 1 Figure 1 1

6、 Table 1 1 Publication(s) referred to Inside back coverBS4215-15:1990 ii BSI 10-1999 Foreword This Part of BS4215, prepared under the direction of the Welding Standards Policy Committee, is based on ISO9312:1990 “Resistance welding equipment Insulated pins for use in electrode back-ups” published by

7、 the International Organization for Standardization (ISO). It differs from the International Standard in specifying material that complies with BS4577 rather than ISO5182. The requirements for the softening temperature in BS4577 are generally more stringent than those in ISO5182. BS4215 is being rev

8、ised in several Parts and supersedes BS4215:1967, which has been withdrawn. Most of the Parts of BS4215 are or will be identical with or based on International Standards but, in instances where the United Kingdom was or is unable to give a vote of approval to the International Standard, a correspond

9、ing British Standard has been or will be prepared, where possible, taking into account the reasons for disapproval. A further Part will also be published in due course, specifying electrodes, electrode holders and ancillary equipment of interest in the UK only. The following Parts of BS4215 have bee

10、n published to date: Part1: Withdrawn (superseded by BS EN25183-1:1992 and BS EN25183-2:1992); Part2: Specification for straight resistance spot welding electrodes; Part3: Withdrawn (superseded by BS EN21089:1992); Part4: Withdrawn (superseded by BS EN25822:1992); Part5: Withdrawn (superseded by BS

11、EN25827:1992); Part6: Specification for electrode adaptors, female taper1:10; Part7: Specification for male electrode caps; Part8: Withdrawn (superseded by BS EN27931:1992); Part9: Withdrawn (superseded by BS EN25183-1:1992); Part10: Withdrawn (superseded by BS EN25183-2:1992); Part11: Withdrawn (su

12、perseded by BS EN28430-1:1992); Part12: Withdrawn (superseded by BS EN28430-2:1992); Part13: Withdrawn (superseded by BS EN28430-3:1992); Part14: Withdrawn (superseded by BS EN29313:1992); Part15: Specification for insulated pins for use in electrode back-ups. As this Part is based on ISO9312:1990,

13、some terminology and certain conventions are not identical with those used in British Standards. The Technical Committee has reviewed the provisions of ISO1642 for which there is no equivalent British Standard, and has decided that they are acceptable for use in conjunction with this Part of BS4215.

14、 A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises

15、 a front cover, an inside front cover, pagesi and ii, pages1 and 2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS4215-15:1990 BSI 10-1999

16、1 1 Scope This Part of BS4215 specifies the requirements for insulated pins used to pin parts in the secondary circuit of resistance welding equipment, or other live equipment, which need to be insulated from each other. NOTEA typical application of insulated pins complying with BS4215-15 is given i

17、n BS EN25827:1992. 2 References The titles of the publications referred to in this standard are listed on the inside back cover. 3 Dimensions The dimensions of the insulated pins shall be as shown in Figure 1 and as given in Table 1. Details left unspecified shall be designed as appropriate. Table 1

18、 4 Designation The designation of insulated pins which comply with BS4215-15 shall comprise the following information in the order given: a) a description block (i.e.“insulated pin”); b) a reference to BS4215-15; c) the pin diameter, d, in millimetres. EXAMPLE An insulated pin with a diameter d=8mm

19、is designated Insulated pin BS4215/158 5 Material The material shall be hard fabric, coarse weave PFCC1, in accordance with ISO1642. 6 Finish Permissible deviations for dimensions without tolerance indications shall be: medium BS4500-3. NOTESee BS308-2 for indication of surface texture. Figure 1 d l

20、 1 l 2 r 6 8 10 12 30 40 50 60 2 2,5 3 3,5 6 8 10 122 blankBS4215-15:1990 BSI 10-1999 Publication(s) referred to BS308, Engineering drawing practice. BS308-2, Recommendations for dimensioning and tolerancing of size. BS4215, Resistance spot welding electrodes, electrode holders and ancillary equipme

21、nt. BS4500, ISO limits and fits. BS4500-3, Working limits on untoleranced dimensions. BS EN25827, Specification for spot welding Electrode back-ups and clamps. ISO1642, Plastics Industrial laminated sheets based on thermosetting resins Specification 1) . ISO5182, Materials for resistance welding ele

22、ctrodes and ancillary equipment 1)2) . 1) This document is available from BSI Sales Department, Linford Wood, Milton Keynes MK146LE. 2) Referred to in the foreword only.BS4215-15: 1990 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body respon

23、sible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendment

24、s or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found o

25、n the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications shoul

26、d be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide

27、range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111.

28、 Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists

29、 in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any me

30、ans electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.