BS 5350-0-1987 Methods of test for adhesives - General introduction《粘合剂的试验方法 一般说明》.pdf

1、BRITISH STANDARD BS 5350-0: 1987 Methods of test for Adhesives Part 0: General introduction UDC 665.93:620.1BS5350-0:1987 This British Standard, having been prepared under the directionof the Adhesives Standards Committee, was published under the authority ofthe Board of BSI and comesinto effect on

2、30 October 1987 BSI 07-1999 First published July 1976 First revision October 1987 The following BSI references relate to the work on this standard: Committee reference ADC/9 Draft for comment 86/52322 DC ISBN 0 580 16176 5 Committees responsible for this British Standard The preparation of this Brit

3、ish Standard was entrusted by the Adhesives Standards Committee (ADC/-) to Technical Committee ADC/9, upon which the following bodies were represented: British Adhesives and Sealants Association British Plastics Federation British Railways Board Chemical Industries Association Electronic Engineering

4、 Association Ministry of Defence PIRA SATRA Footwear Technology Centre Society of Motor Manufacturers and Traders Limited A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance wi

5、th a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 4 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated.

6、 This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date of issue CommentsBS5350-0:1987 BSI 07-1999 i Contents Page Committees responsible Inside front cover General introduction 1 List of Parts of BS 5350 1 Appendix A British Standa

7、rds containing test methods of relevance to adhesives 3ii blankBS5350-0:1987 BSI 07-1999 1 General introduction This Part of BS 5350 has been prepared under the direction of the Adhesives Standards Committee. The standard was first published in 1976 in the form of a series of Parts to provide test m

8、ethods that would be of general applicability to all types of adhesives. The first edition included a General Introduction, of which this Part is a revision, which listed the methods already published as separate Parts of BS5350 and those for which future publication was envisaged. The methods were

9、classified into several groups. As a result of experience in the use of the methods and to meet the need for test methods to be referred to in specifications for particular adhesives or applications published as separate British Standards, additional methods of test have been added and the number of

10、 groups has been extended. The majority of methods now included in BS 5350 are still intended to be of general applicability, but some methods specific to end-use or types of adhesives have been included in the expectation that they will thus find wider use. Parts B3, B6, B7, C8 and D5, listed in th

11、e 1976 edition as being in preparation, have subsequently been deleted from the programme of work. Parts C2, D1, D2 and D3 also listed in the 1976 edition as being in preparation, are covered by projects in preparation within Technical Committee61 Plastics, of the International Organization for Stan

12、dardization (ISO), and will be considered for publication in due course as Parts of BS5350. This Part of BS 5350 supersedes BS 5350: General Introduction: 1976 which is now withdrawn. The methods at present included in BS 5350 are classified into groups as follows: Group A Adherends; Group B Adhesiv

13、es; Group C Adhesively bonded joints: mechanical tests; Group D Adhesively bonded joints: environmental tests; Group E Sampling and analysis of test data; Group F Tests for flooring adhesives; Group G Physical tests on anaerobic adhesives; Group H Physical tests on hot-melt adhesives. The methods de

14、scribed in BS 5350 are based on those already available from other British Standards and other national and international sources as well as those used by the Ministry of Defence. Some of the methods are derived from work in ISO/TC 61. It is the intention that future methods developed in ISO/TC 61,

15、which are approved by the UK, should be incorporated as Parts of BS 5350. Several test methods for adhesives are included in other British Standards. Some of these are specific test methods and some are included as parts of specifications for products or for particular applications. A list of the ti

16、tles of the more important of these standards is given in Appendix A. Terms relating to the testing of adhesives are defined in BS 6138 “Glossary of terms used in the adhesives industry”. List of Parts of BS 5350 The methods already published or in preparation 1)as Parts of BS 5350 are classified as

17、 follows: 1) Methods that have been announced as drafts for comment at the time of publication are included as being in preparation. Group A Adherends Part A1 Adherend preparation Part A2 Selection of adherends 1) Group B Adhesives Part B1 Determination of density Part B2 Determination of solids con

18、tent Part B4 Determination of pot life Part B5 Determination of gelation time Part B8 Determination of viscosity Part B9 Determination of resistance to sagging (flow after application) Group C Adhesively bonded joints:mechanical tests Part C1 Determination of cleavage strength of adhesive bonds Part

19、 C3 Determination of bond strength in direct tension Part C4 Determination of impact resistance of adhesive bonds Part C5 Determination of bond strength in longitudinal shear Part C6 Determination of bond strength in direct tension in sandwich panels Part C7 Determination of creep and resistance to

20、sustained application of force Part C9 Floating roller peel testBS5350-0:1987 2 BSI 07-1999 Part C10 90 peel test for a flexible-to-rigid assembly Part C11 180 peel test for a flexible-to-rigid assembly Part C12 180 “T” peel test for a flexible-to-flexible assembly Part C13 Climbing drum peel test P

21、art C14 90 peel test for rigid-to-rigid assembly Part C15 Determination of bond strength in compressive shear Group D Adhesively bonded joints: environmental tests Part D4 Determination of staining potential Group E Sampling and analysis of test data Part E1 Guide to statistical analysis Part E2 Gui

22、de to sampling Group F Tests for flooring adhesives Part F1 Performance tests for flooring adhesives Group G Physical tests on anaerobic adhesives Part G1 Determination of torque strength of anaerobic adhesives on threaded fasteners Part G2 Determination of static shear strength of anaerobic adhesiv

23、es Part G3 Determination of ability of anaerobic adhesives to set on metal surfaces Group H Physical tests on hot-melt adhesives Part H1 Determination of heat stability of hot-melt adhesives in the application equipment Part H2 Determination of low temperature flexibility or cold crack temperature P

24、art H3 Determination of heat resistance of hot-melt adhesives Part H4 Determination of maximum opentime of hot-melt adhesives (ovenmethod)BS5350-0:1987 BSI 07-1999 3 Appendix A British Standards containing test methods of relevance to adhesives BS 647, Methods for sampling and testing glues (bone, s

25、kin and fish glues). BS 1203, Specification for synthetic resin adhesives (phenolic and aminoplastic) for plywood. BS 1204, Synthetic resin adhesives (phenolic and aminoplastic) for wood. BS 1204-1, Specification for gap-filling adhesives. BS 1204-2, Specification for close-contact adhesives. BS 278

26、2, Methods of testing plastics. BS 2782-7, Rheological properties. BS 2782:Method 720A, Determination of melt flow rate of thermoplastics. BS 2782-8, Other properties. BS 2782:Method 835A, Determination of gelation time of phenolic resins. BS 2782:Method 835B, Determination of gelation time of polye

27、ster resins (manual method). BS 2782:Method 835C, Determination of gelation time of polyester and epoxide resins using a gel timer. BS 2782:Method 835D, Determination of gelation time of thermosetting resins using a hot plate. BS 3046, Specification for adhesives for hanging flexible wallcoverings.

28、BS 3424, Testing coated fabrics. BS 3424-7, Method 9. Method for determination of coating adhesion strength. BS 3544, Methods of test for polyvinyl acetate adhesives for wood. BS 3712, Building and construction sealants. BS 3712-1, Methods of test for homogeneity, relative density, extrudability, pe

29、netration and slump. BS 3712-2, Methods of test for seepage, staining, shrinkage, shelf life and paintability. BS 3712-3, Methods of test for application life, skinning properties and tack-free time. BS 3712-4, Methods of test for adhesion in peel, tensile extension and recovery and loss of mass aft

30、er heat ageing. BS 3887, Adhesive closing and sealing tapes. BS 3887-1, Specification for polypropylene, regenerated cellulose and unplasticized PVC tapes. BS 3924, Specification for pressure-sensitive adhesive tapes for electrical insulating purposes. BS 4169, Specification for glued-laminated timb

31、er structural members. BS 4346, Joints and fittings for use with unplasticized PVC pressure pipes. BS 4346-3, Specification for solvent cement. BS 4781, Specification for self adhesive plastics labels for permanent use. BS 4781-1, General purpose labels. BS 4781-2, Requirements for stringent conditi

32、ons. BS 5131, Methods of test for footwear and footwear materials. BS 5131-1, Adhesives. BS 5131-1.1, Resistance of adhesive joints to heat and to peeling. BS 5131-1.1.1, Resistance to heat (creep test). BS 5131-1.1.2, Resistance to peeling. BS 5131-1.1.3, Preparation of test assemblies for adhesion

33、 tests. BS 5131-1.4, Heat activation life of adhesives. BS 5131-1.6, Recommended environmental storage conditions for adhesive joints prior to heat resistance or peeling tests. BS 5131-1.7, The preparation of hot melt adhesive bonded assemblies for heat resistance (creep) and peel tests. BS 5131-1.8

34、, Rate of bond strength development in shear of hot melt adhesives for lasting. BS 5131-1.9, Measurement of green strength of adhesive joints. BS 5214, Specification for testing machines for rubbers and plastics. BS 5214-1, Constant rate of traverse machines. BS 5214-2, Constant rate of force applic

35、ation machines. BS 5270, Specification for polyvinyl acetate (PVAC) emulsion bonding agents for internal use with gypsum building plasters. BS 5609, Specification for adhesive coated labels for marine use. BS 5980, Specification for adhesives for use with ceramic tiles and mosaics. BS 6138, Glossary

36、 of terms used in the adhesives industry. BS 6209, Specification for solvent cement for non-pressure thermoplastics pipe systems. DD 74, Performance requirements and test methods for non-structural wood adhesives. DD 88, Method for the assessment of pot life of non-flowing resin compositions for use

37、 in civil engineering. BS 3J 10, Specification for pressure-sensitive adhesive waterproof PVC tape.BS5350-0:1987 4 BSI 07-1999 BS 3J 11, Specification for pressure-sensitive adhesive paper masking tape. BS 2J 12, Specification for pressure-sensitive adhesive identification tape.blankBS 5350-0: 1987

38、BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are

39、updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this Brit

40、ishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest

41、 editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that

42、 have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are a

43、lso available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these a

44、nd other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationalstandardization bodies. Except as permitted under the Copyright, Designs and P

45、atents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necess

46、ary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.