BS 5350-C7-1990 Methods of test for adhesives - Adhesively bonded joints mechanical tests - Determination of creep and resistance to sustained application of force《粘合剂试验方法 第C7部分 粘结.pdf

1、BRITISH STANDARD BS 5350-C7: 1990 Methods of test for Adhesives Part C7: Determination of creep and resistance to sustained application of force UDC 665.93:620.1 + 665.93:620.172.2:539.376:539.434BS5350-C7:1990 This British Standard, having been prepared under the directionof the Adhesives Standards

2、 Policy Committee, waspublished under the authorityof the Board of BSI andcomes into effect on 31 August 1990 BSI 07-1999 First published 1976 Second edition August 1990 The following BSI references relate to the work on this standard: Committee reference ADC/9 Draft for comment 89/53400 DC ISBN 0 5

3、80 18776 4 Amendments issued since publication Amd. No. Date of issue CommentsBS5350-C7:1990 BSI 07-1999 i Contents Page Foreword ii 1 Scope 1 2 References 1 3 Apparatus 1 4 Procedure 1 5 Expression of results 2 6 Test report 2BS5350-C7:1990 ii BSI 07-1999 Foreword This Part of this British Standard

4、 has been prepared under the direction of the Adhesives Standards Policy Committee. This edition introduces technical changes but it does not reflect a full review or revision of the standard, which will be undertaken in due course. This edition differs from the previous edition in that the scope ha

5、s been amended to emphasize that the test is not intended to be used for providing numerical design data; also references to other British Standards have been brought up-to-date. Under sustained constant force the adhesive in a bond may flow and allow adherends to move relative to one another. The i

6、rreversible part of this movement is known as creep. The force involved may be very much smaller than that which the bond will support for short periods. All the test methods in which a force is applied to an adhesive bond may be used for the measurement of creep and resistance to sustained applicat

7、ion of force. The tests for determination of cleavage (Part C1), determination of strength in direct tension (Part C3), determination of peel strength (Part C14) and determination of strength in shear (Parts C5 and C15) may be used. These tests may be carried out in the normal environment or under c

8、onditions influenced by other environments. Arrangements are required for observation of the movement of adherends relative to one another, or for determination of time to failure, over extended periods. Such methods are therefore not normally used as batch control tests. The test does not necessari

9、ly reflect how the adhesive would perform in service. Such design data would usually be obtained using the construction materials and configurations used in an actual design. WARNING NOTE. This British Standard calls for the use of substances and/or procedures that may be injurious to health if adeq

10、uate precautions are not taken. It refers only to technical suitability and does not absolve the user from the legal obligations relating to health and safety at any stage. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are respo

11、nsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages1 and 2 and a back cover. This standard has been updated (see copyri

12、ght date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS5350-C7:1990 BSI 07-1999 1 1 Scope This Part of this British Standard describes the application of test methods in which force is applied to an adhesive bond to determine dis

13、placement under constant force, creep and time to failure. In such applications the tests are of necessity over extended periods and are, therefore, not normally used as batch control tests. This test is not intended to be used for obtaining data for design purposes. 2 References This Part makes ref

14、erence to the following British Standards: BS 1610, Materials testing machines and force verification equipment Part 1: Specification for the grading of the forces applied by materials testing machines. BS 3544, Methods of test for polyvinyl acetate adhesives for wood. BS 5350, Methods of test for a

15、dhesives PartC1:Determination of cleavage strength of adhesive bonds Part C3: Determination of bond strength in direct tension Part C5: Determination of bond strength in longitudinal shear PartC14:90 peel test for a rigid-to-rigid assembly Part C15: Determination of bond strength in compressive shea

16、r Part E1: Guide to statistical analysis. 3 Apparatus Apparatus shall be appropriate to the test method used, provided that it is capable of applying the required constant force and of measuring it to the required accuracy. If the force is applied by suspending weights on a test rig the accuracy of

17、the arrangement shall comply with grade 2.0 of BS1610-1:1985. NOTEThe equipment described in clause 5 a) of BS 3544:1962 is suitable for use to obtain time-to-failure data. Provision shall be made to measure small movements accurately over known and sometimes protracted time intervals. This shall be

18、 done by either: a) periodic observations of marked test pieces by cathetometer, measuring microscope, or other suitable device; b) movement of mirrors mounted on knife edges attached to adherends. This allows some magnification of the changes occurring. 4 Procedure 4.1 Adherends Selection, dimensio

19、ns and preparation of adherends shall be in accordance with the procedure laid down in the corresponding test for adhesive bond strength as given in Parts C1, C3, C5, C14 and C15 of this standard. 4.2 Bonding Apply the adhesive and make the bond by the methods recommended by the manufacturer of the

20、adhesive. In the absence of such recommendation, the procedure shall be as indicated in the corresponding test for adhesive bond strength as given in Parts C1, C3, C5, C14 and C15 of this standard. 4.3 Testing Set up the test assembly in the appropriate manner, establish the required environment, an

21、d apply a constant force. If displacement of the adherends is to be measured, observe the displacement at convenient intervals and record the maximum total movement prior to distortion of adherends, failure of the assembly or cessation of movement. If creep only is to be determined, measure the disp

22、lacement when it has stabilized after removal of the force (seenote). NOTEIf in time-to-failure tests periodic observations are made, the chosen conditions of the test should be such that failure of the test pieces occurs at a time compatible with an acceptable experimental error. Largest errors occ

23、ur at shortest time as the following calculation shows. In an 8-hour day errors up to 16 h can occur on weekdays and more at weekends. The maximum error in a 7-day test is 4.4 Number of tests The number of tests depends on the precision required (see Part E1) and shall be reported in the test report

24、. NOTEReliance should not be placed on fewer than five tests. 16100 247 -10 % approximately. =BS5350-C7:1990 2 BSI 07-1999 5 Expression of results The results of the test shall be expressed as: a) the mean of the total movements in millimetres between adherends at the selected intervals, giving an i

25、ndication of the spread of the results and the standard deviation (see Part E1); b) in cases where creep only is to be measured, the total movement in millimetres at the selected interval, calculated as the difference between the original measurement and that measured after the removal of the force;

26、 or c) the mean time to failure. 6 Test report The report shall state the following: a) a designation of the adhesive, giving all information required for complete identification of the sample; b) a description of the adherends and of their pretreatment; c) the method of applying the adhesive, the a

27、mount used or the bond-line thickness, and the open time; d) the method of making the bond, including details of the bonding pressure, temperature, relative humidity and conditioning time; e) the force applied to the bond, the duration of the test, and the environmental conditions; f) the result of

28、the test; g) the state of the test specimens at the end of the test, e.g. distorted, fractured, mode of separation; h) the accuracy of the movement-measuring apparatus (if applicable); i) that the method of test complied with BS 5350-C7; j) any other factor that may have affected the result.blankBS

29、5350-C7: 1990 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British

30、Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while u

31、sing this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically rece

32、ive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation

33、 of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information

34、services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For deta

35、ils of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationalstandardization bodies. Except as permitted under the Copyright,

36、 Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the stand

37、ard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.