1、BRITISH STANDARD CONFIRMED SEPTEMBER 1992 BS 5793-6: 1986 IEC 534-6: 1985 Industrial-process control valves Part 6: Specification for mounting details for attachment of positioners to control valve actuators UDC 66.025:621.646.3:681.533.3BS5793-6:1986 This British Standard, having been prepared unde
2、r the direction of the Industrial-process Measurement and Control Standards Committee, was published under the authority of the Board of BSI and comes into effect on 28November1986 BSI 08-1999 The following BSI references relate to the work on this standard: Committee reference PCL/1 Draft for comme
3、nt 82/32597 DC ISBN 0 580 15529 3 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Industrial-process Measurement and Control Standards Committee (PCL/-) to Technical Committee PCL/1, upon which the following bodies were represented: Brit
4、ish Coal British Gas Corporation British Pressure Gauge Manufacturers Association Department of Energy (Gas and Oil Measurement Branch) Department of Trade and Industry (National Weights and Measures Laboratory) Energy Industries Council Engineering Equipment and Materials Users Association GAMBICA
5、(BEAMA Ltd.) Health and Safety Executive Institution of Gas Engineers The following bodies were also represented in the drafting of the standard, through subcommittees and panels: British Chemical Engineering Contractors Association British Valve Manufacturers Association Ltd. Electricity Supply Ind
6、ustry in England and Wales Amendments issued since publication Amd. No. Date of issue CommentsBS5793-6:1986 BSI 08-1999 i Contents Page Committees responsible Inside front cover National foreword ii 1 Scope and object 1 2 Definitions 1 3 Basic design principles 1 4 Feedback connection 1 5 Mounting p
7、late design 2 6 Actuator mounting 2 7 Mounting accessories 2 Figure 1 3 Figure 2 4 Figure 3 5 Figure 4 5 Figure 5 6 Figure 6 7 Publications referred to Inside back coverBS5793-6:1986 ii BSI 08-1999 National foreword This Part of BS5793 has been prepared under the direction of the Industrial-process
8、Measurement and Control Standards Committee. It is identical with IEC Publication534-6:1985 “Industrial-process control valves. Part6: Mounting details for attachment of positioners to control valve actuators” published by the International Electrotechnical Commission (IEC). Terminology and conventi
9、ons. The text of the International Standard has been approved as suitable for publication as a British Standard without deviation. Some terminology and certain conventions are not identical with those used in British Standards; attention is drawn especially to the following. The comma has been used
10、as a decimal marker in Figure 3 to Figure 6. In BritishStandards it is current practice to use a full point on the baseline. Wherever page numbers are quoted, they are IEC page numbers. The reference to “other parts of IEC Publication534” in clause2 should be read as “other Parts of BS5793”. A Briti
11、sh Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front
12、 cover, an inside front cover, pages i and ii, pages1to8, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS5793-6:1986 BSI 08-1999 1 1 Scope a
13、nd object This standard is intended to permit a variety of positioning devices which respond to a linear motion to be mounted on the actuator of a control valve, either directly or by employing an intermediate mounting bracket. There is a large variety of types, sizes and designs of actuators. The f
14、ollowing parameters define the intended applicability of this standard for the guidance of manufacturers and users. 1.1 The standardized mounting applies only to positioners which are mounted on the side of the actuator. 1.2 The standardized mounting applies in general only to those actuators which
15、have a travel of100mm or less. 1.3 The standardized mounting is designed to cover three basic types of actuator design (see Figure 1, page3): a) those with some form of cast or fabricated yoke to connect the actuator power unit to the valve; b) those which use some form of central tube yoke to conne
16、ct the actuator power unit to the valve; c) those in which the yoke incorporates two or more columns or pillars to connect the actuator power unit to the valve. 2 Definitions All of the definitions given in other parts of IEC Publication534shall apply, with the addition of the following. 2.1 actuato
17、r a device or mechanism which changes a signal into a corresponding movement controlling the position of the internal regulating mechanism of the control valve NOTE 1The signal or energizing force may be pneumatic, electric, hydraulic, or any combination thereof. NOTE 2The actuator comprises an actu
18、ator power unit and a yoke for attachment to the control valve. The yoke may take the form of a casting, a central tube, two or more pillars, or it may be fabricated from stampings (see Figure 1). 2.2 actuating power unit the part of the actuator which converts fluid, electrical, thermal or mechanic
19、al energy into stem motion to develop thrust or torque 2.3 yoke the structure which rigidly connects the actuator power unit to a valve NOTEThe yoke may be an integral part of the actuator power unit in some actuator designs. 2.4 actuator stem the bar or rod between the actuator and the valve which
20、ultimately operates the internal regulating mechanism 3 Basic design principles The objective is to standardize the attachment of the positioner to the side of the actuator to assure compatibility of products from different manufacturers. 3.1 For this purpose the manufacturer of the actuator shall o
21、bserve certain design criteria (seeFigure 1 to Figure 6, pages3to7). These criteria consist of a suitable rib(s) and fixing hole(s) (see Figure 6a) or, alternatively, a shape allowing the mounting plate to be clamped to the side of the actuator using either two U-bolts (see Figure 6c) or two or more
22、 of the four outer mounting holes in the design (see Figure 6b). The design of the positioner mounting shall assure: a) correct positioning of the positioner in relation to the actuator stem; b) rigid mounting of the positioner. 3.2 The manufacturer of the positioner may design a positioner incorpor
23、ating a means of attachment compatible with this standard. Alternatively, a separate mounting plate may be supplied which is compatible with the standardized mounting. 4 Feedback connection In order to standardize the feedback attachment to the actuator a connection piece shall be provided which sha
24、ll have four threaded holes tapped M6surrounded with a bearing area of at least10mm diameter for each hole (see Figure 2, page4). The remaining design of the feedback attachment is not specified and may be designed to meet the requirements of each manufacturer. If the design permits the connection p
25、iece to be rotated through180, only two threaded holes, on one side only, need be provided. The manufacturer of the positioner shall provide adequate means of transmitting the motion of the actuator stem to the positioner by use of the above connection piece.BS5793-6:1986 2 BSI 08-1999 5 Mounting pl
26、ate design The positioner shall either incorporate the attachment means or be provided with a mounting plate in accordance with the details given in Figure 3, page5. It should be noted that only the standardized details are given. Details such as material thickness to provide rigidity and design of
27、mounting means of the positioner have not been standardized. The design of the mounting plate must ensure sufficient contact with the rib to ensure that the objective of Item b) of Sub-clause3.1 is attained. 6 Actuator mounting The actuator shall be provided with a suitable means for mounting the po
28、sitioner as follows: a) by means of ribs of the cross-section shown in Figure 4, page5, and relative position shown in Figure 5, page6; b) by means of two U-bolts as shown in Figure 6, page7, provided that the diameter of the supporting pillars is between20mm and35mm; c) by means of any two of the o
29、uter fixing holes in the bracket on a suitable surface. 7 Mounting accessories The positioner manufacturer shall provide two M8U-bolts plus nuts, and four M8screws to permit the positioner to be mounted to an actuator of any design. The actuator manufacturer shall provide the necessary holes for the
30、 attachment of the mounting plate, either the single central hole, or the two or more alternative holes, as may be dictated by the design of the yoke.BS 5793-6:1986 BSI 08-1999 3 NOTEMidpoint of the threaded holes in the feedback connection at midtravel of the stem. Figure 1 BS 5793-6:1986 4 BSI 08-
31、1999 Figure 2 BS 5793-6:1986 BSI 08-1999 5 Figure 3 Figure 4 BS 5793-6:1986 6 BSI 08-1999 NOTEAt midtravel of the stem. Figure 5 BS 5793-6:1986 BSI 08-1999 7 Figure 6 8 blankBS5793-6:1986 BSI 08-1999 Publications referred to See national foreword.BS 5793-6: 1986 IEC 534-6: 1985 BSI 389 Chiswick High
32、 Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment
33、or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inf
34、orm the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standard
35、s. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published
36、as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which g
37、ive details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits con
38、tact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationalstandardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no ex
39、tract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as s
40、ymbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1