BS 5838-1-1980 Specification for dry packaged cementitious mixes - Prepacked concrete mixes《袋装干水泥混合料规范 第1部分 袋装混凝土混合料》.pdf

1、BRITISH STANDARD BS 5838-1: 1980 Specification for Dry packaged cementitious mixes Part 1: Prepacked concrete mixes UDC 691.54:621.798:691.32BS5838-1:1980 This British Standard, having been prepared under the directionof the Cement, Gypsum,Aggregates and QuarryProducts Standards Committee, was publi

2、shed underthe authority of the Executive Board and comes intoeffect on 29 February 1980 BSI 09-1999 The following BSI references relate to the work on this standard: Committee reference CAB/4 Draft for comment 78/10939 DC ISBN 0 580 11145 8 Cooperating organizations The Cement, Gypsum, Aggregates an

3、d Quarry Products Standards Committee, under whose direction this British Standard was prepared, consists of representatives from the following Government departments and scientific and industrial organizations: The organizations marked with an asterisk in the above list, together with the following

4、, were directly represented on the committee entrusted with the preparation of this British Standard: Association of Consulting Engineers Department of Transport* Association of County Councils Federation of Civil Engineering Contractors* Association of Metropolitan Authorities Federation of Stone I

5、ndustries Autoclaved Aerated Concrete Gypsum Products Development Association Products Association Institute of Quarrying British Precast Concrete Federation Ltd.* Institution of Civil Engineers British Quarrying and Slag Federation* Institution of Highway Engineers* British Railways Board Instituti

6、on of Municipal Engineers* British Ready Mixed Concrete Association* Institution of Public Health Engineers British Steel Industry Institution of Structural Engineers* Cement Admixtures Association* Institution of Water Engineers and Scientists* Cement and Concrete Association* National Federation o

7、f Building Trades Cement Makers Federation* Employers* Chemical Industries Association Natural Environment Research Council Concrete Society Limited* (Institute of Geological Science) Department of the Environment Royal Institute of British Architects (Building Research Establishment)* Royal Institu

8、tion of Chartered Surveyors* Department of the Environment (Housing and Sand and Ballast Hauliers and Allied Trades Construction) Alliance Department of the Environment (PSA)* Sand and Gravel Association Limited* Department of the Environment (Transport Society of Chemical Industry* and Road Researc

9、h Laboratory* Association of Lightweight Aggregate Electricity Supply Industry in England and Manufacturers Wales Cementitious Packaged Products Association Mortar Producers Association Ltd. Concrete Block Association Co-opted member. County Surveyors Society Amendments issued since publication Amd.

10、 No. Date of issue CommentsBS5838-1:1980 BSI 09-1999 i Contents Page Cooperating organizations Inside front cover Foreword ii 1 Scope 1 2 References 1 3 Definitions 1 4 Constituent materials 1 5 Preparation of aggregates 1 6 Types and properties of concrete mixes 1 7 Packaging 1 8 Sampling 1 9 Testi

11、ng 1 Publications referred to Inside back coverBS5838-1:1980 ii BSI 09-1999 Foreword This British Standard has been produced under the direction of the Cement, Gypsum, Aggregates and Quarry Products Standards Committee. It covers factory produced dry mixes of cement, aggregates and, when used, admix

12、tures which are supplied in packages for the do-it-yourself and retail trades. It is intended that the contents of these packages should be mixed on site with the only addition being water. Part 1 of the standard covers prepacked concrete mixes of two grades; coarse concrete mixes containing aggrega

13、te of a nominal maximum size of 20mm and fine concrete mixes containing aggregate of a nominal maximum size of 10mm. Part 2 of the standard covers prepacked cement : lime : sand mortar mixes, and cement : sand mortar mixes for brick-laying, screeding and other building purposes. A British Standard d

14、oes not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an in

15、side front cover, pages i and ii, pages 1 and 2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS5838-1:1980 BSI 09-1999 1 1 Scope This Part

16、of BS5838 specifies, for the do-it-yourself and retail trades, the materials to be used, the methods of describing the grades of concrete, the physical requirements of packaging materials, identification of contents and sampling and testing to determine compliance with this standard. 2 References Th

17、e titles of the publications referred to in this Part of this standard are listed on the inside back cover. 3 Definitions For the purposes of this Part of BS 5838 the following definitions apply. prepacked concrete mixes a prepacked mixture consisting substantially of cement and aggregate requiring

18、only mixing with water before use volume yield the volume of a wet mix of workable consistence obtained from a unit mass of dry material 4 Constituent materials 4.1 Cement. The cement shall be ordinary or rapid-hardening Portland cement complying with the requirements of BS12 or Portland blastfurnac

19、e cement complying with the requirements of BS146. 4.2 Aggregates. Aggregates shall comply with the requirements of BS882, BS1201, BS1047 or BS3797. 4.3 Admixtures. When admixtures are used they shall comply with the requirements of BS 5075-1 and BS 5075-2. 4.4 Chloride. The chloride ion content sha

20、ll be not greater than 0.05% of the mass of the contents of the package. 5 Preparation of aggregates All aggregates, before mixing with the other constituents, shall have a moisture content of less than0.5% by mass when tested in accordance with the requirements of 7.3 of BS 812-2:1975. 6 Types and

21、properties of concrete mixes 6.1 Aggregate sizes. The concrete shall be described as coarse when the nominal maximum size of aggregate is 20mm and as fine when the nominal maximum size of the aggregate is 10mm. 6.2 Compressive strength. The compressive strength at 28 days shall be determined as deta

22、iled in clause9 and shall be not less than 20N/mm 2 . 6.3 Volume yield. The volume yield shall be determined as detailed in clause9 and shall be not less than95% of the nominal volume yield indicated on the package. It shall be reported as the volume of concrete inm 3produced per unit package. 7 Pac

23、kaging 7.1 Identification and marking. Identification and marking of packages shall include the following particulars. a) The number of this British Standard, i.e. BS5838-1. b) Product description. c) Mass and nominal volume yield. d) Description of any admixture. e) Indication of health and safety

24、requirements. f) Advice on storage. g) The name, trademark or other means of identification of the manufacturer or vendor. h) Advice on use and mixing. 7.2 Package construction. The strength of the package shall be adequate to contain the mass of dry concrete mix for which it is intended. The materi

25、al from which the packages are made shall have water vapour transmission not greater than 20g/m 2in24h as determined in accordance with the requirements of BS3177. This requirement shall not apply to packages of less than5kg. 8 Sampling When testing is called for, a combination of whole packages hav

26、ing a total mass of not less than 50kg for every 10tonne of package supplied shall be submitted for testing in accordance with the requirements of clause9. 9 Testing 9.1 General. All sampling, curing and testing of the fresh or hardened concrete shall be carried out in accordance with the requiremen

27、ts of BS1881. 9.2 Preparation of sample. The sample, when received in the laboratory, shall be rendered homogeneous and, if necessary, be reduced in size by coning and quartering, or by any other suitable sampling means, to about 25kg. 9.3 Mixing of sample. The weighed, prepared sample (see9.2) shal

28、l be machine mixed for not less than2min with the amount of water required to give the specified slump.BS5838-1:1980 2 BSI 09-1999 9.4 Workability and water requirement. The workability of the concrete shall be measured by the slump test specified in BS 1881-2 and shall be between50mm and75mm. If th

29、e slump is less than50mm then further water may be added and mixed in to reach the required workability. If the slump is more than75mm the test shall be repeated with a new prepared sample as specified in9.2, using less water. The amount of water to achieve the required workability shall be recorded

30、 as the water requirement and expressed as a percentage by mass of solid ingredients to the nearest 0.1%. 9.5 Volume yield. Immediately after completion of the slump test, the wet bulk density of the fresh concrete shall be determined to the nearest 10kg/m 3in accordance with the requirements of BS1

31、881-2. The volume yield per unit package shall then be calculated to the nearest0.0001m 3from the formula: where 9.6 Making and curing of test cubes. The same concrete shall be used as specified in9.4. The size of test cubes shall be100mm and they shall be made and cured in accordance with the requi

32、rements of BS 1881-3, except that three cubes shall be retained from the same batch for test at28 days age. 9.7 Testing of cubes. The cubes shall be tested for compressive strength in accordance with the requirements of BS 1881-4 and the average of three cubes taken from the same batch and reported

33、to the nearest0.5N/mm 2shall be the test result. V is the volume yield per unit package (m 3 ) W is the mass of unit package (kg) R is the water requirement as determined in9.4 (%) D is the wet bulk density (kg/m 3 ). V R 0.01 W ()W + D - =BS5838-1:1980 BSI 09-1999 Publications referred to BS 12, Sp

34、ecification for ordinary and rapid-hardening Portland cement. BS 146, Portland-blastfurnace cement. BS 812, Methods for sampling and testing of mineral aggregates, sands and fillers. BS 812-2, Physical properties. BS 882, BS 1201, Aggregates from natural sources for concrete (including granolithic).

35、 BS 1047, Specification for air-cooled blastfurnace slag coarse aggregate for concrete. BS 1881, Methods of testing concrete. BS 1881-2, Methods of testing fresh concrete. BS 1881-3, Methods of making and curing test specimens. BS 1881-4, Methods of testing concrete for strength. BS 3177, Method for

36、 determining the permeability to water vapour of flexible sheet materials used for packaging. BS 3797, Specification for lightweight aggregates for concrete. BS 5075, Concrete admixtures. BS 5075-1, Accelerating admixtures, retarding admixtures and water-reducing admixtures. Metric units. BS 5075-2,

37、 Air entraining admixtures 1) . 1) In course of preparation.BS 5838-1: 1980 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international

38、 level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be

39、 grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service

40、 called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for internationa

41、l standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical

42、Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive subs

43、tantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international s

44、tandardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not

45、 preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.