BS AU 50-4 5 1-1995 Tyres and wheels - Rim profiles and dimensions - Industrial vehicle rims - Specification for rim profiles and dimensions for code-designated series tyres《轮胎和车轮 .pdf

1、BRITISH STANDARD AUTOMOBILE SERIES BS AU 50-4.5.1:1995 Tyres and wheels Part 4: Rim profiles and dimensions Section 5: Industrial vehicle rims Subsection 5.1 Specification for rim profiles and dimensions for code-designated series tyresBSAU 50-4.5.1:1995 This British Standard, having been prepared u

2、nder the directionof the Engineering SectorBoard, was published underthe authority of the Standards Board and comes intoeffect on 15 April 1995 BSI 09-1999 The following BSI references relate to the work on this standard: Committee reference AUE/4 Draft for comment 94/702520 DC ISBN 0 580 23721 4 Co

3、mmittees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee AUE/4, Tyres and wheels for road vehicles, upon which the following bodies were represented: Agricultural Engineers Association Automobile Association British Industrial Truck

4、 Association British Pressure Gauge Manufacturers Association British Rubber Manufacturers Association Confederation of Passenger Transport UK Department of Transport Freight Transport Association Institute of Road Transport Engineers (Inc) Motor Cycle Industrys Association of Great Britain Ltd. Mot

5、or Industry Research Association National Tyre Distributors Association Retread Manufacturers Association Road Haulage Association Ltd. Society of Motor Manufacturers and Traders Ltd. Amendments issued since publication Amd. No. Date CommentsBSAU 50-4.5.1:1995 BSI 09-1999 i Contents Page Committees

6、responsible Inside front cover Foreword ii 1 Scope 1 2 References 1 3 Definitions 1 4 Designation and marking 1 5 Rim profiles 1 Annex A (normative) Ball tape and mandrel dimensions for verifying specified rim diameter 8 Figure 1 Rims with 5 tapered bead seat 2 Figure 2 Divided rims 4 Figure 3 Flat

7、base rims 5 Figure 4 Drop-centre 15 tapered rims for normal base tyres 6 Figure A.1 Use of ball tape to measure rim circumference 8 Table 1 Rims with 5 tapered bead seat rims: contour dimensions 2 Table 2 Rims with 5 tapered bead seat: size programme 3 Table 3 Divided rims: rim contour dimensions 4

8、Table 4 Divided rims: size programme 4 Table 5 Flat base rims: rim contour dimensions 5 Table 6 Flat base rims: size programme 5 Table 7 Drop-centre 15 tapered rims for normal base tyres: rim contour dimensions 7 Table 8 Drop-centre 15 tapered rims for normal base tyres: size programme 7 Table A.1 B

9、all tape and mandrel dimensions 9 List of references Inside back coverBSAU 50-4.5.1:1995 ii BSI 09-1999 Foreword This British Standard has been prepared by Technical Committee AUE/4. This Subsection forms part of Section 5 of this British Standard. This Subsection specifies rim profiles and dimensio

10、ns suitable for use with the code-designated series tyres specified in BSAU50-1.5.1. Requirements for rims for metric series tyres are specified in the other Subsections of Section 5. Part 4 of this standard is concerned with rim profiles and dimensions. Other Parts are as follows: Part 1: Tyres; Pa

11、rt 2: Wheels and rims; Part 3: Valves. Other Sections of Part 4 are as follows: Section 1: Passenger car rims; Section 2: Commercial vehicle rims; Section 3: Off-the-road vehicle rims; Section 4: Agricultural vehicle rims; Section 5: Industrial vehicle rims; Section 6: Motor cycle rims; Section 7: M

12、oped rims. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document

13、 comprises a front cover, an inside front cover, pages i and ii, pages1 to 10, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BSAU 50-4.5.1:19

14、95 BSI 09-1999 1 1 Scope This Subsection of BSAU50-4 specifies contours and dimensions of rims for use with code-designated series tyres used on industrial vehicles. Requirements for such tyres are specified in BSAU50-1.5.1:1994. Requirements for rim construction and workmanship are specified in BSA

15、U50-2.0:1979. SAFETY NOTE. The wheel manufacturer should also be consulted to determine whether the rim and wheel is of sufficient strength for the intended service. In particular, care should be taken to ensure that the wheel will withstand the maximum pressure of any tyre that can be fitted in acc

16、ordance with BSAU50-1.5.1:1994. This pressure may exceed1000 kPa (10bar) for both diagonal and radial tyres. 2 References 2.1 Normative reference This Subsection of BS AU50-4 incorporates, by dated or undated reference, provisions from another publication. This normative reference is made at the app

17、ropriate places in the text and the cited publication is listed on the inside back cover. For dated references, only the edition cited applies; any subsequent amendments to or revisions of the cited publication apply to this Subsection of BSAU50-4 only when incorporated by amendment or revision. For

18、 undated references the latest edition of the cited publication applies, together with any amendments. 2.2 Informative reference This Subsection of BSAU50-4 refers to another publication that provides information or guidance. The edition of this publication current at the time of issue of this stand

19、ard is listed on the inside back cover, but reference should be made to the latest edition. 3 Definitions For the purpose of this Subsection of BSAU50-4 the definitions given in BSAU50-2.0:1979 apply. 4 Designation and marking Rims shall be designated and marked in accordance with BSAU50-2.0:1979. 5

20、 Rim profiles 5.1 Rims with 5 tapered bead seat Rims with 5 tapered bead seat rim profiles shall be in accordance with Figure 1 andTable 1 andTable 2. The specified rim diameter shall be verified by measuring the wheel rim circumference with a ball tape. The measured circumference shall be within 1.

21、2mm of the nominal circumference of the appropriate mandrel, as specified inAnnex A. 5.2 Divided rims Divided rim profiles shall be in accordance withFigure 2 and Table 3 andTable 4. The specified rim diameter shall be verified by measuring the wheel rim circumference with a ball tape. The measured

22、circumference shall be within 1.2mm of the nominal circumference of the appropriate mandrel, as specified inAnnex A. 5.3 Flat base rims Flat base rim profiles shall be in accordance withFigure 3 andTable 5andTable 6. 5.4 Drop-centre 15 tapered rims for normal base tyres Drop-centre 15 tapered rim pr

23、ofiles for normal base tyres shall be in accordance withFigure 4 andTable 7 andTable 8. The specified rim diameter shall be verified by measuring the wheel rim circumference with a ball tape. The measured circumference shall be within 1.2mm of the nominal circumference of the appropriate mandrel, as

24、 specified inAnnex A.BSAU 50-4.5.1:1995 2 BSI 09-1999 Table 1 Rims with 5 tapered bead seat rims: contour dimensions Figure 1 Rims with 5 tapered bead seat Dimensions in millimetres Rim contour designation A G B min. P min. C R 1 R 2 R 3 max. 3.00 D 76.2 17.5 11.5 14.2 12.4 13.0 4.3 8.1 4.00 E 101.6

25、 19.8 11.7 28.0 13.6 14.2 6.4 8.6 5.0 127.0 27.9 15.7 36.3 14.0 8.0 5.00 F 127.0 22.2 12.2 23.8 14.5 15.6 6.4 9.5 5.00 S 127.0 31.3 18.3 43.0 18.3 8.0 5.5 139.7 30.6 17.0 36.3 15.2 8.0 5.50 F 139.7 22.2 12.2 34.0 14.5 15.6 6.4 9.5 6.0 152.4 33.0 18.3 36.3 16.5 8.0 6.00 E 152.4 19.8 11.7 28.0 13.6 14

26、2 6.4 8.6 6.5 165.1 35.6 19.6 36.3 17.1 8.0 B6.5 165.1 38.1 20.8 27.3 19.0 8.0 6.50 F 165.1 22.2 12.2 34.0 14.5 15.6 6.4 9.5 7.0 177.8 38.1 20.8 36.3 19.0 8.0 B7.0 177.8 38.1 20.8 27.3 19.0 8.0 7.5 190.5 40.6 22.1 36.3 20.3 8.0 B7.5 190.5 43.2 23.4 27.3 21.6 8.0 8.0 203.2 43.2 23.4 36.3 21.6 8.0 B8

27、0 203.2 43.2 23.4 27.3 21.6 8.0 8.00 G 203.2 27.9 14.0 40.6 14.0 7.5 8.5 215.9 45.7 24.6 36.3 22.9 8.0 B8.5 215.9 45.7 24.6 27.3 22.9 8.0 10.0 254.0 50.8 27.2 36.3 27.0 8.0BSAU 50-4.5.1:1995 BSI 09-1999 3 Table 2 Rims with 5 tapered bead seat: size programme Dimensions in millimetres Rim contour de

28、signation Nominal rim diameter code 8 9 10 12 15 20 24 Specified rim diameter D 3.00 D 202.4 4.00 E 227.8 5.0 387.4 514.4 616.0 5.00 F 253.2 5.00 S 232.6 308.8 5.5 387.4 514.4 616.0 5.50 F 253.2 6.0 387.4 514.4 616.0 6.00 E 227.8 6.5 387.4 514.4 616.0 B6.5 385.8 512.8 6.50 F 253.2 7.0 387.4 514.4 61

29、6.0 B7.0 385.8 512.8 7.5 387.4 514.4 616.0 B7.5 385.8 512.8 8.0 387.4 514.4 616.0 B8.0 385.8 512.8 8.00 G 304.0 8.5 514.4 616.0 B8.5 512.8 10.0 514.4 616.0BSAU 50-4.5.1:1995 4 BSI 09-1999 Table 3 Divided rims: rim contour dimensions Table 4 Divided rims: size programme Figure 2 Divided rims Dimensio

30、ns in millimetres Rim contour designation A G B C P R 1 R 2 R 3 R 8 2.10 53.3 11.9 8.0 7.0 11.5 7.0 3.2 250 C 63.5 16.0 10.4 11.5 11.0 12.0 3.2 3.5 min. 3.00 D 76.2 17.5 11.5 12.4 14.2 13.0 4.5 8.1 3! I 82.5 15.8 9.7 8.9 4.3 7.9 3# I 95.2 15.8 9.7 8.9 4.3 7.9 4.33 R 110.0 27.8 21.5 34.0 18.0 6.4 12.

31、0 5.00 F 127.0 22.2 12.2 14.5 23.8 15.6 6.4 9.5 12.0 5.00 S 127.0 31.3 18.3 43.0 18.3 8.0 15.8 Dimensions in millimetres Rim contour designation Nominal rim diameter code 4 8 12 Specified rim diameter D 2.10 100.8 2.50 C 100.8 202.4 3.00 D 202.4 3! I 202.4 3# I 202.4 4.33 R 205.1 5.00 F 205.1 5.00 S

32、 308.8BSAU 50-4.5.1:1995 BSI 09-1999 5 Table 5 Flat base rims: rim contour dimensions Table 6 Flat base rims: size programme Figure 3 Flat base rims Dimensions in mm Rim contour designation A G B min. P min. R 1 R 2 max. 3.11 F 79.0 22.0 12.2 25.0 16.0 5.5 3.75 P 95.2 25.4 19.1 25.0 16.0 6.4 4.33 R

33、110.0 28.6 21.5 34.0 18.0 6.4 6.00 S 152.4 33.3 18.3 45.0 18.3 6.4 Dimensions in millimetres Rim contour designation Nominal rim diameter code 8 12 13 Specified rim diameter D 3.11 F 330.2 3.75 P 330.2 4.33 R 202.4 381.0 6.00 S 381.0BS AU 50-4.5.1:1995 6 BSI 09-1999 Figure 4 Drop-centre 15 tapered r

34、ims for normal base tyresBSAU 50-4.5.1:1995 BSI 09-1999 7 Table 7 Drop-centre 15 tapered rims for normal base tyres: rim contour dimensions Table 8 Drop-centre 15 tapered rims for normal base tyres: size programme Dimensions in millimetres Rim contour designation A P L Q H h 3.2 min. min. max. a min

35、 min. 6.0 152.4 25 11 60 24 8.5 6.75 171.5 25 11 62 24 9.0 a Larger dimensions may be used where these are verified by type mounting trials. Dimensions in millimetres Rim contour designation Nominal rim diameter code 17.5 Specified rim diameter D 6.0 444.5 6.75 444.5BSAU 50-4.5.1:1995 8 BSI 09-1999

36、 Annex A (normative) Ball tape and mandrel dimensions for verifying specified rim diameter The nominal mandrel circumference is related to the ball tape diameter and the specified diameter of the rim as given inTable A.1. When measured with a ball tape, in accordance withFigure A.1 the measured circ

37、umference shall be equal to the nominal mandrel circumference specified inTable A.1, to a tolerance of 1.2mm Figure A.1 Use of ball tape to measure rim circumferenceBS AU 50-4.5.1:1995 BSI 09-1999 9 Table A.1 Ball tape and mandrel dimensions Dimensions in millimetres Taper Nominal diameter code Spec

38、ified diameter D 1 Ball diameter 8 Ball diameter 10 Ball diameter 16 Nominal mandrel diameter D 1 Nominal mandrel circumference Nominal mandrel diameter D 1 Nominal mandrel circumference Nominal mandrel diameter D 1 Nominal mandrel circumference 1 30 8 a 205.1 204.69 643.1 5 4 100.8 100.14 314.6 8 2

39、02.4 201.74 633.8 201.57 633.2 201.07 631.7 9 227.8 227.14 713.6 226.97 713.0 226.47 711.5 10 253.2 252.54 793.4 252.37 792.8 251.87 791.3 12 304.0 303.34 953.0 303.17 952.4 302.67 950.9 12 b 308.8 307.43 965.8 13 330.2 329.53 1035.2 329.37 1034.7 328.87 1033.2 15 c 385.8 384.42 1207.7 15 387.4 386.

40、01 1212.7 20 c 512.8 511.42 1606.7 20 514.4 513.01 1611.7 24 616.0 614.61 1930.9 15 17.5 444.5 441.32 1386.5 22.5 571.5 568.32 1785.4 a Only for industrial rim 4.33 R b Only for industrial rim 5.00 S c Only for “B” CV rims10 blankBSAU 50-4.5.1:1995 BSI 09-1999 List of references (see 1.2) Normative

41、references BSI publications BRITISH STANDARDS INSTITUTION, London BS AU 50, Tyres and wheels. BS AU 50-2, Wheels and rims. BS AU 50-2.0:1979, Wheels General (including terms and definitions, and construction and workmanship). Informative references BSI publications BRITISH STANDARDS INSTITUTION, Lon

42、don BS AU 50, Tyres and wheels. BS AU 50-1, Tyres. BS AU 50-1.5, Industrial vehicle tyres. BS AU 50-1.5.1:1994, Specification for code-designated series tyres. BS AU 50-4.5.1:1995 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible

43、 for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or

44、editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the

45、 inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be

46、addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range

47、 of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:

48、02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international