BS AU 50-4 5 1-1995 Tyres and wheels - Rim profiles and dimensions - Industrial vehicle rims - Specification for rim profiles and dimensions for code-designated series tyres《轮胎和车轮 .pdf
《BS AU 50-4 5 1-1995 Tyres and wheels - Rim profiles and dimensions - Industrial vehicle rims - Specification for rim profiles and dimensions for code-designated series tyres《轮胎和车轮 .pdf》由会员分享,可在线阅读,更多相关《BS AU 50-4 5 1-1995 Tyres and wheels - Rim profiles and dimensions - Industrial vehicle rims - Specification for rim profiles and dimensions for code-designated series tyres《轮胎和车轮 .pdf(16页珍藏版)》请在麦多课文档分享上搜索。
1、BRITISH STANDARD AUTOMOBILE SERIES BS AU 50-4.5.1:1995 Tyres and wheels Part 4: Rim profiles and dimensions Section 5: Industrial vehicle rims Subsection 5.1 Specification for rim profiles and dimensions for code-designated series tyresBSAU 50-4.5.1:1995 This British Standard, having been prepared u
2、nder the directionof the Engineering SectorBoard, was published underthe authority of the Standards Board and comes intoeffect on 15 April 1995 BSI 09-1999 The following BSI references relate to the work on this standard: Committee reference AUE/4 Draft for comment 94/702520 DC ISBN 0 580 23721 4 Co
3、mmittees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee AUE/4, Tyres and wheels for road vehicles, upon which the following bodies were represented: Agricultural Engineers Association Automobile Association British Industrial Truck
4、 Association British Pressure Gauge Manufacturers Association British Rubber Manufacturers Association Confederation of Passenger Transport UK Department of Transport Freight Transport Association Institute of Road Transport Engineers (Inc) Motor Cycle Industrys Association of Great Britain Ltd. Mot
5、or Industry Research Association National Tyre Distributors Association Retread Manufacturers Association Road Haulage Association Ltd. Society of Motor Manufacturers and Traders Ltd. Amendments issued since publication Amd. No. Date CommentsBSAU 50-4.5.1:1995 BSI 09-1999 i Contents Page Committees
6、responsible Inside front cover Foreword ii 1 Scope 1 2 References 1 3 Definitions 1 4 Designation and marking 1 5 Rim profiles 1 Annex A (normative) Ball tape and mandrel dimensions for verifying specified rim diameter 8 Figure 1 Rims with 5 tapered bead seat 2 Figure 2 Divided rims 4 Figure 3 Flat
7、base rims 5 Figure 4 Drop-centre 15 tapered rims for normal base tyres 6 Figure A.1 Use of ball tape to measure rim circumference 8 Table 1 Rims with 5 tapered bead seat rims: contour dimensions 2 Table 2 Rims with 5 tapered bead seat: size programme 3 Table 3 Divided rims: rim contour dimensions 4
8、Table 4 Divided rims: size programme 4 Table 5 Flat base rims: rim contour dimensions 5 Table 6 Flat base rims: size programme 5 Table 7 Drop-centre 15 tapered rims for normal base tyres: rim contour dimensions 7 Table 8 Drop-centre 15 tapered rims for normal base tyres: size programme 7 Table A.1 B
9、all tape and mandrel dimensions 9 List of references Inside back coverBSAU 50-4.5.1:1995 ii BSI 09-1999 Foreword This British Standard has been prepared by Technical Committee AUE/4. This Subsection forms part of Section 5 of this British Standard. This Subsection specifies rim profiles and dimensio
10、ns suitable for use with the code-designated series tyres specified in BSAU50-1.5.1. Requirements for rims for metric series tyres are specified in the other Subsections of Section 5. Part 4 of this standard is concerned with rim profiles and dimensions. Other Parts are as follows: Part 1: Tyres; Pa
11、rt 2: Wheels and rims; Part 3: Valves. Other Sections of Part 4 are as follows: Section 1: Passenger car rims; Section 2: Commercial vehicle rims; Section 3: Off-the-road vehicle rims; Section 4: Agricultural vehicle rims; Section 5: Industrial vehicle rims; Section 6: Motor cycle rims; Section 7: M
12、oped rims. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document
13、 comprises a front cover, an inside front cover, pages i and ii, pages1 to 10, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BSAU 50-4.5.1:19
14、95 BSI 09-1999 1 1 Scope This Subsection of BSAU50-4 specifies contours and dimensions of rims for use with code-designated series tyres used on industrial vehicles. Requirements for such tyres are specified in BSAU50-1.5.1:1994. Requirements for rim construction and workmanship are specified in BSA
15、U50-2.0:1979. SAFETY NOTE. The wheel manufacturer should also be consulted to determine whether the rim and wheel is of sufficient strength for the intended service. In particular, care should be taken to ensure that the wheel will withstand the maximum pressure of any tyre that can be fitted in acc
16、ordance with BSAU50-1.5.1:1994. This pressure may exceed1000 kPa (10bar) for both diagonal and radial tyres. 2 References 2.1 Normative reference This Subsection of BS AU50-4 incorporates, by dated or undated reference, provisions from another publication. This normative reference is made at the app
17、ropriate places in the text and the cited publication is listed on the inside back cover. For dated references, only the edition cited applies; any subsequent amendments to or revisions of the cited publication apply to this Subsection of BSAU50-4 only when incorporated by amendment or revision. For
18、 undated references the latest edition of the cited publication applies, together with any amendments. 2.2 Informative reference This Subsection of BSAU50-4 refers to another publication that provides information or guidance. The edition of this publication current at the time of issue of this stand
19、ard is listed on the inside back cover, but reference should be made to the latest edition. 3 Definitions For the purpose of this Subsection of BSAU50-4 the definitions given in BSAU50-2.0:1979 apply. 4 Designation and marking Rims shall be designated and marked in accordance with BSAU50-2.0:1979. 5
20、 Rim profiles 5.1 Rims with 5 tapered bead seat Rims with 5 tapered bead seat rim profiles shall be in accordance with Figure 1 andTable 1 andTable 2. The specified rim diameter shall be verified by measuring the wheel rim circumference with a ball tape. The measured circumference shall be within 1.
21、2mm of the nominal circumference of the appropriate mandrel, as specified inAnnex A. 5.2 Divided rims Divided rim profiles shall be in accordance withFigure 2 and Table 3 andTable 4. The specified rim diameter shall be verified by measuring the wheel rim circumference with a ball tape. The measured
22、circumference shall be within 1.2mm of the nominal circumference of the appropriate mandrel, as specified inAnnex A. 5.3 Flat base rims Flat base rim profiles shall be in accordance withFigure 3 andTable 5andTable 6. 5.4 Drop-centre 15 tapered rims for normal base tyres Drop-centre 15 tapered rim pr
23、ofiles for normal base tyres shall be in accordance withFigure 4 andTable 7 andTable 8. The specified rim diameter shall be verified by measuring the wheel rim circumference with a ball tape. The measured circumference shall be within 1.2mm of the nominal circumference of the appropriate mandrel, as
24、 specified inAnnex A.BSAU 50-4.5.1:1995 2 BSI 09-1999 Table 1 Rims with 5 tapered bead seat rims: contour dimensions Figure 1 Rims with 5 tapered bead seat Dimensions in millimetres Rim contour designation A G B min. P min. C R 1 R 2 R 3 max. 3.00 D 76.2 17.5 11.5 14.2 12.4 13.0 4.3 8.1 4.00 E 101.6
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
本资源只提供5页预览,全部文档请下载后查看!喜欢就下载吧,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BSAU504511995TYRESANDWHEELSRIMPROFILESANDDIMENSIONSINDUSTRIALVEHICLERIMSSPECIFICATIONFORRIMPROFILESANDDIMENSIONSFORCODEDESIGNATEDSERIESTYRES

链接地址:http://www.mydoc123.com/p-547852.html