BS EN 2591-409-1999 Elements of electrical and optical connection - Test methods - Contact retention in insert《光电连接件 试验方法 触点插接稳固性》.pdf

1、BRITISH STANDARD AEROSPACE SERIES BS EN 2591-409:1999 Elements of electrical and optical connection Test methods Part409: Contact retention in insert The European Standard EN2591-409:1999 has the status of a BritishStandard ICS49.060BSEN2591-409:1999 This BritishStandard, having been prepared under

2、the directionof the Engineering SectorCommittee, was publishedunder the authorityofthe Standards Committeeandcomes into effect on 15June1999 BSI03-2000 ISBN 0 580 32645 4 National foreword This BritishStandard is the English language version of EN2591-409:1999. The UK participation in its preparatio

3、n was entrusted by Technical Committee ACE/6, Aerospace avionic, electrical and fibre optic technology, to Subcommittee ACE/6/3, Aerospace connectors, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on t

4、he interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British St

5、andards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Stan

6、dard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover,

7、 an inside front cover, pagesi andii, theEN title page, pages2 and3 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Da

8、te CommentsBSEN2591-409:1999 BSI 03-2000 i Contents Page National foreword Inside front cover Foreword 2 Text of EN2591-409 3ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN2591-409 March1999 ICS49.060 English version Aerospace series Elements of electrical and optical connection Test me

9、thods Part409: Contact retention in insert Srie arospatiale Organes de connexion lectrique et optique Mthodes dessais Partie409: Rtention du contact dans lisolant Luft- und Raumfahrt Elektrische und optische Verbindungselemente Prfverfahren Teil409: Festsitzen des Kontaktes im Kontakteinsatz This Eu

10、ropean Standard was approved by CEN on23February1998. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references c

11、oncerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its

12、own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, S

13、weden, Switzerland and UnitedKingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1999 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national

14、 Members. Ref.No.EN2591-409:1999EEN2591-409:1999 BSI 03-2000 2 Foreword This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After inquiries and votes carried out in accordance with the rules of this Association, this Standard has received the appr

15、oval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September1999, and c

16、onflicting national standards shall be withdrawn at the latest by September1999. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, CzechRepublic, Denmark, Finland, France

17、, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the UnitedKingdom. Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Preparation of specimens 3 4 Method 3 4.1 Number of contacts to be tested for each size 3 4.2 Procedu

18、re 3 4.3 Final measurements and requirements 3 Table 1 3EN2591-409:1999 BSI 03-2000 3 1 Scope This standard specifies a method of assessing the retention in insert of contacts used in elements of connection subjected to axial loads. It shall be used together with EN2591. 2 Normative references This

19、European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publicati

20、ons apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN2591, Aerospace series Elements of electrical and optical connection Test methods General. EN2591-101, Aerospace series Eleme

21、nts of electrical and optical connection Test methods Part101: Visual examination. 3 Preparation of specimens 3.1 The specimens shall be fitted with all their contacts according to the technical specification. Any accessories which are not essential to the retaining system performance shall be remov

22、ed. If during a test sequence, the specimens are wired, contacts to be tested shall be replaced by unwired contacts. 3.2 Unless specified in the technical specification, the following details shall be stated: mounting of the specimens; preload value; load to be applied and its application point; all

23、owable displacements: 1) under load, 2) after removal of load, final measurements and requirements (ifapplicable). 4 Method 4.1 Number of contacts to be tested for each size SeeTable 1. Table 1 At least one contact shall be close to the insert periphery and one near the centre. 4.2 Procedure Each co

24、ntact shall be submitted to the specified axial preload. The load shall be increased at a rate not exceeding5N/s until the specified value is reached and maintained for10s. The maximum contact displacement shall be measured: while the load is applied; after the load is removed. This test shall then

25、be repeated in the opposite direction. 4.3 Final measurements and requirements (ifapplicable) The measured values shall be within the specified limits. The specimens shall be submitted to a visual examination (EN2591-101). No damage which would impair their operation shall be observed. Number of con

26、tacts Number to be tested % 1to5 6to60 61to130 U 131 100 50(with a minimum of6 specimens) 25(with a minimum of31 specimens) 10(with a minimum of34 specimens)BS EN 2591-409:1999 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible fo

27、r preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or edi

28、tions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the in

29、side front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be add

30、ressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of

31、 information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:020

32、89967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all

33、BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means elec

34、tronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.