BS EN 60512-15-8-1997 Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Mechanical tests on contacts and terminations - Test l.pdf

1、BRITISH STANDARD BS EN 60512-15-8: 1997 IEC 512-15-8: 1995 Electromechanical components for electronic equipment Basic testing procedures and measuring methods Part 15: Mechanical tests on contacts and terminations Section 8: Test 15h. Contact retention system resistance to tool application The Euro

2、pean Standard EN 60512-15-8:1995 has the status of a British Standard ICS 31.220.01BSEN60512-15-8:1997 This British Standard, having been prepared under the directionof the Electrotechnical Sector Board, was published underthe authority of the Standards Board and comes intoeffect on 15March1997 BSI

3、02-1999 The following BSI references relate to the work on this standard: Committee reference EPL/48/2 Announced in BSI Update February1997 ISBN 0 580 27311 3 Committees responsible for this British Standard The preparation of this British Standard was entrusted by Technical Committee EPL/48, Electr

4、omechanical components for electronic equipment, to Subcommittee EPL/48/2, Connectors for electronic equipment, upon which the following bodies were represented: Association of Manufacturers Allied to the Electrical and Electronic Industry (BEAMA Ltd.) British Telecommunications plc BSI Quality Assu

5、rance Federation of the Electronics Industry Ministry of Defence Premises Cabling Association Amendments issued since publication Amd. No. Date CommentsBSEN60512-15-8:1997 BSI 02-1999 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 Text of EN 60512-15-8 3 Li

6、st of references Inside back coverBSEN60512-15-8:1997 ii BSI 02-1999 National foreword This Section of BS EN 60512 has been prepared by Subcommittee EPL/48/2, and is the English language version of EN60512-15-8:1995 Electromechanical components for electronic equipment Basic testing procedures and m

7、easuring methods Part15: Mechanical tests on contacts and terminations Section8:Test15h: Contact retention system resistance to tool application, published by the European Committee for Electrotechnical Standardization (CENELEC). It is identical with IEC512-15-8:1995, published by the International

8、Electrotechnical Commission (IEC). A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-

9、references Publication referred to Corresponding British Standard IEC 512-8:1993 BS 5772 Specification for electromechanical components for electronic equipment Basic testing procedures and measuring methods Part 8:1985 Connector tests (mechanical) and mechanical tests on contacts and terminations S

10、ummary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages 2 to 6, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment t

11、able on theinside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 60512-15-8 December 1995 ICS 31.220.10 Descriptors: Test, contact retention system resistance to tool application English version Electromechanical components for electronic equipment Basic testing procedures and meas

12、uring methods Part 15: Mechanical tests on contacts and terminations Section 8: Test 15h Contact retention system resistance to tool application (IEC 512-15-8:1995) Composants lectromcaniques pour quipements lectroniques Procduresdessai de base et mthodes de mesure Partie 15: Essais mcaniques des co

13、ntacts et des sorties Section 8: Essai 15h Rsistance du systme de rtention des contacts lutilisation des outils (CEI 512-15-8:1995) Elektrisch-mechanische Bauelemente fr elektronische Einrichtungen Me- und Prfverfahren Teil 15: Mechanische Prfungen an Kontakten und Anschlssen Hauptabschnitt 8: Prfun

14、g15h Kontakthalterung, widerstandsfhigheit bei Verwendungen von Werkzeugen (IEC 512-15-8:1995) This European Standard was approved by CENELEC on 1995-11-28. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard

15、the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French,

16、German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denm

17、ark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotech

18、nische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1995 Copyright reserved to CENELEC members Ref. No.EN 60512-15-8:1995 EEN60512-15-8:1995 BSI 02-1999 2 Foreword The text of document 48B/421/DIS, as prepared by SC48B, Connectors, of IEC TC48, Electromechanical components and me

19、chanical structures for electronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN60512-15-8 on1995-11-28. The following dates were fixed: Annexes designated “normative” are part of the body of the standard. In this standard, Annex ZA is normative. Annex Z

20、A has been added by CENELEC. Contents Page 1 Scope and object 3 2 Normative references 3 3 Preparation of specimens 3 4 Test method 3 5 Final measurements 3 6 Details to be specified 3 Annex ZA (normative) Normative references tointernational publications with their correspondingEuropean publication

21、s 5 Figure 1 Alternating rotations of the tool 4 latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 1996-09-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 1996

22、-09-01EN60512-15-8:1995 BSI 02-1999 3 1 Scope and object This section of IEC512-15 defines standard test method to check the ability of connectors to withstand the use of standardised tooling for insertion and extraction of contacts. 2 Normative references The following normative documents contain p

23、rovisions which, through reference in this text, constitute provisions of this section of IEC512-15. At the time of publication, the editions indicated were valid. All normative documents are subject to revision, and parties to agreements based on this section of IEC512-15 are encouraged to investig

24、ate the possibility of applying the most recent editions of the normative documents indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. IEC 512-2:1985, Electromechanical components for electronic equipment; basic testing procedures and measuring met

25、hods Part 2: General examination, electrical continuity and contact resistance tests, insulation tests and voltage stress tests. Amendment1(1994) IEC 512-8:1993, Electromechanical components for electronic equipment; basic testing procedures and measuring methods Part 8: Connector tests (mechanical)

26、 and mechanical tests on contacts and terminations. NOTEThis series of documents is in process of being revised; the future numbering is referenced in brackets later in this standard. 3 Preparation of specimens The specimens shall be fitted with all their contacts, wired in accordance with the detai

27、l specification. 4 Test method For each test method described, five contacts shall be tested. Separate contact cavities shall be used for method1 and for method2. Method 1: Rotation of the extraction tool The specified extraction tool shall be introduced into a cavity containing the contact. An axia

28、l load as specified in the detail specification shall be applied and maintained while alternating rotations of the tool are carried out as shown inFigure 1. The contact shall then be extracted with the extraction tool, and then reintroduced with the appropriate insertion tool. This operation shall b

29、e carried out three times on each of the five contacts. Method 2: Rotation of the insertion tool The contact shall first be withdrawn and reinserted into its cavity using the insertion tool on which an axial load as specified in the detail specification is applied. With this load maintained, alterna

30、ting rotations, as shown inFigure 1, shall be carried out. The tool is then extracted and the contact withdrawn with the extraction tool. This operation shall be carried out three times on each of the five contacts. If a tool is damaged during the test, a new tool shall be used. 5 Final measurements

31、 The specimens shall be subjected to the following tests, if applicable: visual examination (test1a of IEC512-2 IEC512-1-1); contact retention in insert (test15a of IEC512-8 IEC512-15-1). 6 Details to be specified When this test is required by the detail specification, the following details shall be

32、 specified: a) type and size of wire used; b) tool for insertion of contacts; c) tool for extraction of contacts; d) axial load to be applied on the tool for methods1 and2; e) value of contact retention force.EN60512-15-8:1995 4 BSI 02-1999 Figure 1 Alternating rotations of the toolEN60512-15-8:1995

33、 BSI 02-1999 5 Annex ZA (normative) Normative references to international publications with their corresponding European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places

34、in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred

35、 to applies (including amendments). NOTEWhen the international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 512-2 1985 Electromechanical components for electronic equipment basic testing procedures and me

36、asuring methods Part 2: General examination, electrical continuity and contact resistance tests, insulation tests and voltage stress tests A1 1994 IEC 512-8 1993 Part 8: Connector tests (mechanical) and mechanical tests on contacts and terminations 6 blankBSEN60512-15-8:1997 BSI 02-1999 List of refe

37、rences See national foreword.BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

38、| | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by a

39、mendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standar

40、d would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest edi

41、tions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those th

42、at have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services ar

43、e also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details o

44、f these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyrigh

45、t, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the sta

46、ndard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.