BS EN 60512-5-1-2002 Connectors for electronic equipment - Tests and measurements - Current-carrying capacity tests - Test 5a - Temperature rise《电子设备连接器 试验和测量 载流容量试验 试验5a 温升》.pdf

1、BRITISH STANDARD BS EN 60512-5-1:2002 Connectors for electronic equipment Tests and measurements Part 5-1: Current-carrying capacity tests Test 5a: Temperature rise The European Standard EN 60512-5-1:2002 has the status of a British Standard ICS 31.220.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS

2、PERMITTED BY COPYRIGHT LAWBS EN 60512-5-1:2002 This British Standard, having been prepared under the direction of the Electrotechnical Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 29 May 2002 BSI 29 May 2002 ISBN 0 580 3972

3、5 4 National foreword This British Standard is the official English language version of EN 60512-5-1:2002. It is identical with IEC 60512-5-1:2002. The UK participation in its preparation was entrusted by Technical Committee EPL/48, Electromechanical components and mechanical structures for electron

4、ic equipment, to Subcommittee EPL/48/2, Connectors for electronic equipment, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. From 1 January 1997, all IEC publications have the number 60000 added to the old number.

5、 For instance, IEC 27-1 has been renumbered as IEC 60027-1. For a period of time during the change over from one numbering system to the other, publications may contain identifiers from both systems. Cross-references The British Standards which implement international or European publications referr

6、ed to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a co

7、ntract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the inter

8、pretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 5 and a back cover. The BSI copy

9、right date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEAN STANDARD EN 60512-5-1 NORME EUROPENNE EUROPISCHE NORM April 2002 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Norm

10、alisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2002 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60512-5-1:2002 E ICS 31.220.10 English ver

11、sion Connectors for electronic equipment - Tests and measurements Part 5-1: Current-carrying capacity tests - Test 5a: Temperature rise (IEC 60512-5-1:2002) Connecteurs pour quipements lectroniques - Essais et mesures Partie 5-1: Essais de courant limite - Essai 5a: Echauffement (CEI 60512-5-1:2002)

12、 Steckverbinder fr elektronische Einrichtungen - Mess- und Prfverfahren Teil 5-1: Prfungen der Strombelastbarkeit - Prfung 5a: Temperaturerhhung (IEC 60512-5-1:2002) This European Standard was approved by CENELEC on 2002-04-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regula

13、tions which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This

14、 European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members

15、 are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.NE 065-21-5:12002 - 2 - Foreword The text of document

16、 48B/1136/FDIS, future edition 1 of IEC 60512-5-1, prepared by SC 48B, Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60512-5-1 on 2002-04-01. The following da

17、tes were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2003-01-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2005-04-01 Annexes designated “normat

18、ive“ are part of the body of the standard. In this standard, annex ZA is normative. Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60512-5-1:2002 was approved by CENELEC as a European Standard without any modification. _ Page2 EN6051251:2002 BSI29

19、May2002065-21-51 EI:C0022 3 CONNECTORS FOR ELECTRONIC EQUIPMENT TESTS AND MEASUREMENTS Part 5-1: Current-carrying capacity tests Test 5a: Temperature rise 1 General 1.1 Scope and object This part of IEC 60512, when required by the detail specification, is used for testing electromechanical component

20、s within the scope of IEC technical committee 48. This test may also be used for similar devices when specified in a detail specification. The object of this test is to detail a standard test method to assess the ability of a component to carry its specified current, at room temperature, without exc

21、eeding a specified temperature rise. 1.2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of IEC 60512. For dated references, subsequent amend- ments to, or revisions of, any of these publications do n

22、ot apply. However, parties to agreements based on this part of IEC 60512 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of

23、 IEC and ISO maintain registers of currently valid International Standards. IEC 60512-1-1, Connectors for electronic equipment Tests and measurements Part 1-1: General examination Test 1a: Visual examination 2 Preparation of the specimen Three specimens shall be used, unless otherwise specified. The

24、 specimens are to be wired with a minimum length of wire, as specified in table 1, and mounted, as specified in the detail specification. The manufacturers recommended, or industry standards, wiring method and tooling shall be used, unless otherwise stated in the detail specification. The specimens

25、shall be fitted with a temperature-sensing device, whose thermal mass shall not significantly affect the temperature measurement. This temperature-sensing device shall be mounted as near as practicable to the hottest part of the contact system, unless otherwise specified. A non-contact temperature m

26、easurement device may be used. NOTE Care must be taken to protect the specimen under test from draughts or other artificial cooling. This may be achieved either by the use of an enclosure or by ensuring that the laboratory is draught-free. If d.c. current is used, avoid voltage bias influence on the

27、rmocouple by executing the test with reverse current. Page3 EN6051251:2002 BSI29May2002065-21-51 EI:C0022 4 Table 1 Minimum wire length for each specimen Wire size mm 2 Minimum length mm 5 1 400 NOTE This table is based on heat conduction criteria, and is designed to ensure that the wires are long c

28、ompared with their cross-section. If the specimens require the use of printed circuits, the characteristics of these should be given in the detail specification. 3 Test method The specified test current shall be applied simultaneously to all contacts of the specimen, unless otherwise specified in th

29、e detail specification. The current shall be maintained until thermal stability is achieved. This is defined as when three consecutive measurements of temperature rise, taken at 5 min intervals, do not differ by more than 2 K. The current shall be maintained for a period of 1 h after stability is re

30、ached. The ambient temperature shall be recorded during the test. Care shall be taken to minimize radiant heat effects. 4 Requirements a) Measurement during the test Each contact of the specimen shall be capable of carrying the specified test current for a period of 1 h without exceeding the specifi

31、ed temperature rise of 30 K, unless otherwise specified in the detail specification. b) Final measurement The specimens shall be checked by the following test: Visual examination: IEC 60512-1-1, Test 1a There shall be no defect in the specimen that would impair normal operation. 5 Details to be spec

32、ified When this test is required by the detail specification, the following details shall be specified: a) wire size; b) wiring of specimen and type of termination; c) mounting of specimen; d) location, nature and characteristics of temperature-sensing devices; e) current, a.c. or d.c.; f) number of

33、 specimens, if necessary; g) number of contacts simultaneously under current, if necessary; h) temperature rise, if necessary; i) any deviation from the standard test method. _ Page4 EN6051251:2002 BSI29May2002- 3 - EN 065-21-5:12002 Annex ZA (normative) Normative references to international publica

34、tions with their corresponding European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subs

35、equent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). NOTE When an international publication has be

36、en modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60512-1-1 - 1) Connectors for electronic equipment - Tests and measurements Part 1-1: General examination - Test 1a: Visual examination EN 60512-1-1 2002 2)1)Undated reference.

37、2)Valid edition at date of issue. Page5 EN6051251:2002 BSI29May2002BS EN 60512-5-1:2002 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at t

38、he international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and ser

39、vices. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers m

40、embers an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44

41、(0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Informatio

42、n on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the I

43、nformation Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administ

44、ration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright

45、 subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or

46、by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.