BS EN 62317-2-2010 Ferrite cores Dimensions nPart 2 Pot-cores for use in ntelecommunications power supply and nfilter applications《铁氧体磁芯 尺寸规格 第2部分 电信 电源和过滤器设施中应用的罐形磁心》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 62317-2:2010Ferrite cores Dimensions -Part 2: Pot-cores for use intelecommunications, power supply, andfilter applicationsBS EN 62317-2:2010 BRITISH STANDARDNational forewo

2、rdThis British Standard is the UK implementation of EN 62317-2:2010. It is identical to IEC 62317-2:2010. It supersedes BS EN 60133:2001 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee EPL/51, Transformers, inductors, magnetic componentsand ferrite mate

3、rials.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2010 ISBN 978 0 580 64341 5 ICS 29.100.10 Compliance wi

4、th a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 September 2010. Amendments issued since publicationDate Text affectedEUROPEAN STANDARD EN 62317-2 NORME EUROPENNE EUROPISCHE

5、NORM July 2010 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2010 CENELEC - All rights of exploitation in any form and by any mean

6、s reserved worldwide for CENELEC members. Ref. No. EN 62317-2:2010 E ICS 29.100.10 Supersedes EN 60133:2001Incorporates corrigendum August 2010English version Ferrite cores - Dimensions - Part 2: Pot-cores for use in telecommunications, power supply, and filter applications (IEC 62317-2:2010) Noyaux

7、 ferrites - Dimensions - Partie 2: Circuits magntiques en pots utiliss dans des applications de tlcommunications, dalimentation lectrique et de filtre (CEI 62317-2:2010) Ferritkerne - Mae - Teil 2: Schalenkerne fr die Verwendung in Telekommunikations-, Stromversorgungs- und Filteranwendungen (IEC 62

8、317-2:2010) This European Standard was approved by CENELEC on 2010-07-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibl

9、iographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibili

10、ty of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germa

11、ny, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 62317-2:2010 - 2 - Foreword The text of document 51/980/FDIS, future edition 1 of IEC 6231

12、7-2, prepared by IEC TC 51, Magnetic components and ferrite materials, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 62317-2 on 2010-07-01. This European Standard supersedes EN 60133:2001. The main changes with respect to EN 60133:2001 are listed below: changed “e

13、dimension” of P4,6/3,1 in Table 6 from 3,20 Max. to 3,40 Max.; removed “derived standards” from Annex B (informative) in EN 60133:2001; changed the name of core parts in Subclause 3.1.2 from “Grooves” to “Wire-ways” in accordance with EN 62317-1 Subclause 5.6. Attention is drawn to the possibility t

14、hat some of the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent rights. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identic

15、al national standard or by endorsement (dop) 2011-04-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2013-07-01 The contents of the corrigendum of August 2010 have been included in this copy. Annex ZA has been added by CENELEC. _ Endorsement notice T

16、he text of the International Standard IEC 62317-2:2010 was approved by CENELEC as a European Standard without any modification. _ BS EN 62317-2:2010- 3 - EN 62317-2:2010 Annex ZA (normative) Normative references to international publications with their corresponding European publications The followi

17、ng referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by

18、common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60205 - Calculation of the effective parameters of magnetic piece parts EN 60205 - IEC 62317-1 - Ferrite cores - Dimensions - Part 1: General specification EN 62317-1 - BS EN 62317-2:2010 2 62

19、317-2 IEC:2010 CONTENTS 1 Scope.5 2 Normative references .5 3 Primary standards 5 3.1 Dimensions of pot-cores5 3.1.1 Principal dimensions5 3.1.2 Wire-ways .7 3.1.3 Effective parameter values 8 3.2 Main dimensions for coil formers .9 Annex A (informative) Pot-core design.11 Annex B (informative) Exam

20、ple of a standard for gauges to check the dimensions of pot-cores meeting the IEC primary standard .12 Figure 1 Principal dimensions of pot-cores without back-wall slots.6 Figure 2 Principal dimensions of pot-cores with back-wall slots7 Figure 3 Main dimensions of coil formers for pot-cores 9 Figure

21、 B.1 Dimensions of gauge A .12 Figure B.2 Dimensions of gauges B and C .13 Table 1 Principal dimensions of pot-cores6 Table 2 Limits for dimensions C and G .7 Table 3 Minimum wire-way depth .8 Table 4 Effective parameter values pot-cores with a centre hole 8 Table 5 Effective parameter values pot-co

22、res without a centre hole .9 Table 6 Main dimensions of coil formers for pot-cores10 Table A.1 Ratio of diameter to height.11 Table B.1 Dimensions of gauge A 12 Table B.2 Dimensions of gauges B and C 13 BS EN 62317-2:201062317-2 IEC:2010 5 FERRITE CORES DIMENSIONS Part 2: Pot-cores for use in teleco

23、mmunications, power supply, and filter applications 1 Scope This part of IEC 62317 specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of pot-cores made of ferrite, and the dimensional limits for coil formers to be used with them. The selection of

24、core sizes for this standard is based on the philosophy of including those sizes which are industrial standards, either by inclusion in a national standard, or by broad-based use in industry. See IEC 62317-1 for more detail concerning the philosophy of selecting core sizes to be included. The genera

25、l considerations upon which the design of this range of cores is based are given in Annex A. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edit

26、ion of the referenced document (including any amendments) applies. IEC 60205, Calculation of the effective parameters of magnetic piece parts IEC 62317-1, Ferrite cores Dimensions Part 1: General specification 3 Primary standards 3.1 Dimensions of pot-cores Compliance with the following requirements

27、 ensures mechanical interchangeability of complete assemblies and wound coil formers. 3.1.1 Principal dimensions The principal dimensions of pot-cores shall be as given in Table 1, Figure 1 and Figure 2. BS EN 62317-2:2010 6 62317-2 IEC:2010 Table 1 Principal dimensions of pot-cores Dimensions in mi

28、llimetres A E F H 2B 2D r1aSize Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Max. Figures P3,3/2,6 3,18 3,30 2,50 2,60 1,30 1,40 2,50 2,60 1,70 1,90 0,20 1 P4,6/3,1 4,40 4,60 3,50 3,65 1,90 2,00 3,00 3,10 2,10 2,30 0,20 1 P5,8/3,3 5,65 5,80 4,50 4,60 2,40 2,50 0,95 1,05 3,20 3,30 2,20

29、 2,40 0,20 1 P7,4/4,0 7,15 7,35 5,80 5,95 2,95 3,00 1,05 1,15 4,10 4,20 2,80 3,00 0,20 1 P9/5 9,00 9,30 7,50 7,75 3,70 3,90 2,00 2,20 5,10 5,40 3,60 3,90 0,25 2 P11/7 10,9 11,3 9,00 9,40 4,50 4,70 2,00 2,20 6,30 6,60 4,40 4,70 0,25 2 P14/8 13,8 14,3 11,6 12,0 5,80 6,00 3,00 3,20 8,20 8,50 5,60 6,00

30、0,25 2 P18/11 17,6 18,4 14,9 15,4 7,30 7,60 3,00 3,20 10,4 10,7 7,20 7,60 0,25 2 P22/13 21,2 22,0 17,9 18,5 9,10 9,40 4,40 4,70 13,2 13,6 9,20 9,60 0,35 2 P26/16 25,0 26,0 21,2 22,0 11,1 11,5 5,40 5,70 15,9 16,3 11,0 11,4 0,35 2 P30/19 29,5 30,5 25,0 25,8 13,1 13,5 5,40 5,70 18,6 19,0 13,0 13,4 0,35

31、 2 P36/22 35,0 36,2 29,9 30,9 15,6 16,2 5,40 5,70 21,4 22,0 14,6 15,0 0,35 2 NOTE P3,3/2,6 and P4,6/3,1 cores are without the centre hole shown in Figure 1. aSharp inner corners of pot-cores are preferable but in practice some rounding may occur, provided that radius r1is not exceeded. X Section X-X

32、 G A EfH 2B2Dr1X F IEC 1378/10 Figure 1 Principal dimensions of pot-cores without back-wall slots BS EN 62317-2:201062317-2 IEC:2010 7 C G A EF H 2B 2D r1X X Section X-X IEC 1379/10 Figure 2 Principal dimensions of pot-cores with back-wall slots NOTE The dimensions of the cores may be checked by mea

33、ns of gauges. By way of example, a possible standard for these gauges is given in Annex B. In order to facilitate production it may be necessary to use gauges having dimensions differing from those given in Annex B, although no relaxation of the requirements for the dimensions of the cores given in

34、Table 1 and in Table 2 is permitted. Table 2 Limits for dimensions C and G Dimensions in millimetres Cores with back-wall slots C G Size Min. Max. Min. Max. P3,3/2,6 0,8 1,3 P4,6/3,1 1,1 1,7 P5,8/3,3 1,4 2,0 P7,4/4,0 1,6 2,2 P9/5 6,0 7,5 1,6 2,4 P11/7 6,5 8,0 1,8 2,6 P14/8 8,7 10,0 2,3 4,1 P18/11 11

35、,3 14,0 2,7 4,4 P22/13 13,3 16,5 3,0 4,4 P26/16 17,0 20,0 3,0 4,4 P30/19 20,0 23,0 3,5 5,3 P36/22 24,0 27,2 4,0 5,6 NOTE 1 The shape of the slots is not defined, but the width G is indicated in the table. NOTE 2 It is recommended that any tightening of the tolerance on dimensions C should be towards

36、 the minimum value and on dimension G towards the maximum value. 3.1.2 Wire-ways Wire-ways are recesses in the floor of the pot-core, corresponding to the back-wall slots, which allow a path for wire leads from the centre of the coil to the outside. When wire-ways are provided, their minimum depth s

37、hall be as given in Table 3. BS EN 62317-2:2010 8 62317-2 IEC:2010 Table 3 Minimum wire-way depth Dimensions in millimetres Size Wire-way depth P14/8 0,2 P18/11 0,3 P22/13 0,4 P26/16 0,5 P30/19 0,6 P36/22 0,6 3.1.3 Effective parameter values The effective parameter values for pot-cores whose dimensi

38、ons comply with 3.1.1 shall be as given in Table 4 and Table 5 (for the definitions of these parameters, and their calculation, see IEC 60205). Table 4 Effective parameter values pot-cores with a centre hole Size C1mm1C2103mm3Aemm2lemm Vemm3Aminmm2P5,8/3,3 1,632 6 345,47 4,73 7,72 36,5 3,66 P7,4/4,0

39、 1,358 8 186,79 7,27 9,88 71,9 5,79 P9/5 1,203 2 118,12 10,2 12,3 125 7,88 P11/7 0,933 53 56,727 16,5 15,4 253 13,2 P14/8 0,757 42 29,521 25,7 19,4 499 19,8 P18/11 0,573 83 12,863 44,6 25,6 1 140 36,0 P22/13 0,480 78 7,418 5 64,8 31,2 2 020 50,9 P26/16 0,389 23 4,060 5 95,9 37,3 3 580 76,1 P30/19 0,

40、323 43 2,332 1 139 44,9 6 220 115 P36/22 0,256 66 1,249 2 205 52,7 10 800 172 BS EN 62317-2:201062317-2 IEC:2010 9 Table 5 Effective parameter values pot-cores without a centre hole Size C1mm1C2103mm3Aemm2lemm Vemm3Aminmm2P3,3/2,6 3,136 7 1 768,4 1,77 5,56 9,87 1,43 P4,6/3,1 2,088 7 609,06 3,43 7,16

41、 24,6 2,60 P5,8/3,3 1,540 6 295,89 5,21 8,02 41,8 3,66 P7,4/4,0 1,294 1 163,38 7,92 10,3 81,2 5,79 P9/5 1,063 9 84,640 12,6 13,4 168 8,95 P11/7 0,865 00 46,165 18,7 16,2 304 13,2 P14/8 0,680 99 22,061 30,9 21,0 649 23,6 P18/11 0,540 12 10,923 49,4 26,6 1 320 36,0 P22/13 0,438 12 5,773 5 75,9 33,2 2

42、520 58,1 P26/16 0,355 34 3,183 1 112 39,7 4 430 87,0 P30/19 0,304 43 1,988 8 153 46,6 7 130 117 P36/22 0,246 93 1,128 5 219 54,0 11 800 172 3.2 Main dimensions for coil formers Main dimensions for coil formers shall be in accordance with Figure 3 and Table 6. NOTE The dimensions of Table 6 which cor

43、respond to similar dimensions in Table 1 are labelled with the same letter in upper case, for example, 2d corresponds to 2D in Table 1. f 2deIEC 1380/10 Figure 3 Main dimensions of coil formers for pot-cores BS EN 62317-2:2010 10 62317-2 IEC:2010 Table 6 Main dimensions of coil formers for pot-cores

44、 Dimensions in millimetres Main dimensions for coil formers e f 2d Size Max. Min. Max. P3,3/2,6 2,40 1,50 1,60 P4,6/3,1 3,40 2,10 2,00 P5,8/3,3 4,40 2,60 2,10 P7,4/4,0 5,70 3,10 2,70 P9/5 7,40 4,00 3,50 P11/7 8,90 4,80 4,30 P14/8 11,5 6,10 5,50 P18/11 14,8 7,70 7,10 P22/13 17,8 9,50 9,10 P26/16 21,1

45、 11,6 10,9 P30/19 24,9 13,6 12,9 P36/22 29,8 16,3 14,5 BS EN 62317-2:201062317-2 IEC:2010 11 Annex A (informative) Pot-core design The pot-cores covered by this standard were originally designed for optimum dimensions based upon minimum loss Rdc/L. Before optimizing for performance, the following ho

46、le diameter ranges were chosen: 0,95 mm to 1,05 mm for P5,8/3,3 1,05 mm to 1,15 mm for P7,4/4,0 2,0 mm to 2,2 mm for P9/5, P11/7 3,0 mm to 3,2 mm for P14/8, P18/11 4,4 mm to 4,7 mm for P22/13 5,4 mm to 5,7 mm for P26/16, P30/19, P36/22 Originally a pot-core 14 mm 8 mm, with an adjusting device of 3

47、mm diameter was the smallest that could be produced in quantity. Due to miniaturization of electronic devices, four smaller pot-cores, P7,4/4,0, P5,8/3,3, P4,6/3,1 and P3,3/2,6 were added as standard pot-cores, and the larger pot-core P42/29 was deleted. The ratio of diameter to height of the pot-co

48、re, calculated on the above assumption, is fairly constant, as appears from the list below, where A/2B lies between 1,48 and 1,76, except for the smallest type. Table A.1 Ratio of diameter to height Size A (nom.) 2B (nom.) A/2B P3,3/2,6 3,24 2,55 1,27 P4,6/3,1 4,50 3,05 1,48 P5,8/3,3 5,73 3,25 1,76

49、P7,4/4,0 7,25 4,15 1,75 P9/5 9,15 5,25 1,74 P11/7 11,1 6,50 1,71 P14/8 14,05 8,35 1,68 P18/11 18,0 10,55 1,71 P22/13 21,6 13,4 1,61 P26/16 25,5 16,15 1,58 P30/19 30,0 18,8 1,60 P36/22 35,6 21,7 1,64 The steps in the series are such that the ratio of Rdc/L of two adjacent pot-cores is about 1,6. BS EN 62317-2:2010 12 62317-2 IEC:2010 Annex B (informative) Example of a standard for gauges to