BS HC 106-1974 Specification for precipitaton hardening chromium-nickel-copper corrosion-resisting steel castings (1250-1500 MPa) (Cr 16 Ni 4 Cu 3)《沉淀硬化铬-镍-铜耐腐蚀钢铸件(1250-1500MPa)(铬1.pdf

1、BRITISH STANDARD AEROSPACE SERIES CONFIRMED JULY 1982 BS HC 106:1974 Incorporating Amendment Nos. 1 and 2 Specification for Precipitation hardening chromium-nickel- copper corrosion-resisting steel castings (12501500 MPa) (Cr 16, Ni 4, Cu 3) UDC 629.7:669.1524263 14:669.14.018.298.3:669.14.018.8BSHC

2、106:1974 This British Standard, having been approved by the AerospaceIndustry StandardsCommittee, waspublished under theauthorityofthe ExecutiveBoardon 29November1974 BSI 03-2000 The following BSI references relate to the work on this standard: Committee reference ACE/60 Draft for comment 73/33283 D

3、C ISBN 0 580 08790 5 A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages Thi

4、s document comprises a front cover, an inside front cover, pages i and ii, pages 1 and 2 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since pu

5、blication Amd. No. Date of issue Comments 3843 May 1982 5049 May 1986 Indicated by a sideline in the marginBSHC106:1974 BSI 03-2000 i Contents Page 1 Special foundry approval 1 2 Inspection and testing procedure 1 3 Chemical composition 1 4 Condition 1 5 Heat treatment 1 6 Mechanical properties 2 7

6、Rectification of defects 2 8 Flaw detection 2ii blankBSHC106:1974 BSI 03-2000 1 1 Special foundry approval Manufacture of castings to this specification may be restricted to foundries specially approved in accordance with the requirements of BSHC100, Section 1. 2 Inspection and testing procedure Thi

7、s British Standard shall be used in conjunction with the relevant sections of the latest issue of BSHC100, as follows: 3 Chemical composition The re-melting stock and the castings shall contain: 4 Condition Castings shall be supplied in the solution treated condition, unless otherwise agreed between

8、 the purchaser and the founder, in which case the condition required shall be stated on the drawing or order. 5 Heat treatment 5.1 General. The heat treatment shall be as given in5.2 or5.3. NOTEIf the procedure given in5.2 is not acceptable to the purchaser and founder they may use the procedure giv

9、en in5.3. Theprocedure to be used should be stated on the drawing or order. 5.2 Heat treatment I 5.2.1 Solution treatment. Solution treatment shall consist of: a) heating uniformly at a temperature between1020 C and1180 C for not less than1h and cooling to a temperature not exceeding25 C; b) holding

10、 at a temperature not exceeding25 C for not less than24h before further treatment. 5.2.2 Precipitation treatment. Precipitation treatment shall consist of heating uniformly at a temperature between450 C and520 C for not more than4h and cooling in air. 5.2.3 Full heat treatment. Full heat treatment s

11、hall consist of solution treatment in accordance with5.2.1, followed by precipitation treatment in accordance with5.2.2. 5.2.4 Homogenization. Homogenization treatment shall consist of: a) heating uniformly at a temperature between1135 C and1165 C for not less than90min and cooling in air to a tempe

12、rature not exceeding25 C; b) holding at a temperature not exceeding25 C for not less than24h before further treatment. Re-melting stock Sections 1 and 2 Precision castings Sections 1 and 3 Sand castings Sections 1 and 4 Centrifugal castings Sections 1 and 5 Element % min. max. Carbon 0.08 Silicon 1.

13、0 Manganese 1.0 Phosphorus 0.04 Sulphur 0.04 Chromium 15.0 17.5 Copper 2.0 3.0 Niobium + Tantalum 0.4 Nickel 3.0 5.0BSHC106:1974 2 BSI 03-2000 5.3 Heat treatment II 5.3.1 Solution treatment. Solution treatment shall consist of: a) heating uniformly at a temperature between1025 C and1055 C for1h per2

14、5mm of section or for30min, whichever is the greater, and cooling in air to a temperature not exceeding25 C; b) holding at a temperature not exceeding25 C for not less than24h before further treatment. 5.3.2 Precipitation treatment. Precipitation treatment shall consist of heating uniformly at a tem

15、perature between450 C and520 C for not less than90min and not more than4h, and cooling in air to room temperature. 5.3.3 Full heat treatment. Full heat treatment shall consist of homogenization treatment in accordance with5.2.4, followed by solution treatment in accordance with5.3.1, followed by pre

16、cipitation treatment in accordance with5.3.2. 6 Mechanical properties 6.1 Tensile. The tensile properties obtained from test pieces representing castings, selected, prepared and tested in accordance with the relevant requirements of BSHC100, shall be: NOTEInformation on SI units is given in BS3763 “

17、The International System of units (SI)”, and BS350 “Conversion factors andtables”. 6.2 Hardness. The hardness of castings fully heat treated in accordance with5.3 and of their representative test samples shall be not less than375HB, 395HV or40HRC. 7 Rectification of defects 7.1 Correction of distort

18、ion. When permitted in accordance with BSHC100, Section 1, distortion can best be corrected after solution treatment in accordance with5.1. If required by the drawing or order, castings shall subsequently be subjected to the precipitation treatment in accordance with5.2. 7.2 Repair of castings by we

19、lding. When repair by welding is permitted in accordance with BSHC100, Section 1, this shall be carried out after solution treatment and castings shall subsequently be re-solution treated and precipitation treated. 8 Flaw detection The chemical composition of this steel is such that spurious indicat

20、ions may result from magnetic methods of flaw detection, therefore penetrant or other non-magnetic methods shall be used. 0.2% proof stress Tensile strength Elongation Reduction of area min. min. max. min. min. MPa (=N/mm 2 ) MPa (=N/mm 2 ) MPa (=N/mm 2 ) % % 1 030 1 250 1 500 8 20blankBS HC 106:197

21、4 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards ar

22、e updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this Br

23、itishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the late

24、st editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those th

25、at have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are

26、 also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these

27、 and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs an

28、d Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of nec

29、essary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.