BS ISO 6695-2015 Cycles Pedal axle and crank assembly with square end fitting Assembly dimensions《自行车 方榫中轴和曲柄的配合 装配尺寸》.pdf

1、BSI Standards PublicationBS ISO 6695:2015Cycles Pedal axle and crankassembly with square endfitting Assembly dimensionsBS ISO 6695:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 6695:2015.It supersedes BS 6102-14:1991 which is withdrawn.The UK participati

2、on in its preparation was entrusted to TechnicalCommittee GME/25, Cycles.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctappli

3、cation. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 86129 1ICS 43.150Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee

4、on 31 December 2015.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS ISO 6695:2015 ISO 2015Cycles Pedal axle and crank assembly with square end fitting Assembly dimensionsCycles Axe de pdalier et manivelle emmanchement carr Dimensions dassemblageINTERNATIONAL STANDARDISO6

5、695Second edition2015-12-15Reference numberISO 6695:2015(E)BS ISO 6695:2015ISO 6695:2015(E)ii ISO 2015 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2015, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwis

6、e in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. d

7、e Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 6695:2015ISO 6695:2015(E)Foreword iv1 Scope . 12 Dimensions . 1 ISO 2015 All rights reserved iiiContents PageBS ISO 6695:2015ISO 6695:2015(E)ForewordISO (the Internatio

8、nal Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been

9、established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standar

10、dization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance

11、 with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of a

12、ny patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsemen

13、t.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information.The committee responsible

14、 for this document is ISO/TC 149, Cycles.This second edition cancels and replaces the first edition (ISO 6695:1991), which has been technically revised with the following modifications:a) in Figure 1, illustration of cross section of bottom bracket spindle added;b) in Figure 1, illustration of crank

15、 revised and front-view added;c) in Figure 1, dimensions added and revised;d) in Figure 1 and Table 1, half wedge angle 1/2 added;e) in Table 1, dimensions and tolerances revised and specified;f) editorial changes.iv ISO 2015 All rights reservedBS ISO 6695:2015INTERNATIONAL STANDARD ISO 6695:2015(E)

16、Cycles Pedal axle and crank assembly with square end fitting Assembl y dimensions1 ScopeThis International Standard specifies the dimensions for the assembly of cranks on bottom bracket spindles with square end fittings.2 DimensionsDimensions for the assembly of cranks on bottom bracket spindles wit

17、h square end fittings shall be as given in Figure 1 and Table 1.Dimensions in millimetresa) Bottom bracket spindle Square end dimensionsb) Bottom bracket spindle with external threadc) Bottom bracket spindle Cross section A-Ad) Bottom bracket spindle with internal thread ISO 2015 All rights reserved

18、 1BS ISO 6695:2015ISO 6695:2015(E)e) Crank f) AssemblyKey1 reference plane (section plane)Figure 1 Dimensions for the assembly of cranks on bottom bracket spindles with square end fittingsTable 1 Dimensions and tolerancesDimensions in millimetresSpindle CrankAssem-blyl12/c D l1d l2d1l3aRight sideLef

19、t side18 002,+18 002,+4010+205+12730 0500 020,+ M10 1,25 6H/6g10050 ,M8 1 6H/6g20,0 min.M22 1 6H/6g15020,aAfter tightening once to the suppliers recommended tightening torque.2 ISO 2015 All rights reservedBS ISO 6695:2015BS ISO 6695:2015ISO 6695:2015(E)ICS 43.150Price based on 2 pages ISO 2015 All r

20、ights reservedThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Stand

21、ards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embod

22、ied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your orga

23、nization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, thr

24、ough our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standard

25、s easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date.

26、You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive

27、the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few o

28、r as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our product

29、s and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the property of and

30、copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no e

31、xtract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW