BS ISO 6695-2015 Cycles Pedal axle and crank assembly with square end fitting Assembly dimensions《自行车 方榫中轴和曲柄的配合 装配尺寸》.pdf
《BS ISO 6695-2015 Cycles Pedal axle and crank assembly with square end fitting Assembly dimensions《自行车 方榫中轴和曲柄的配合 装配尺寸》.pdf》由会员分享,可在线阅读,更多相关《BS ISO 6695-2015 Cycles Pedal axle and crank assembly with square end fitting Assembly dimensions《自行车 方榫中轴和曲柄的配合 装配尺寸》.pdf(12页珍藏版)》请在麦多课文档分享上搜索。
1、BSI Standards PublicationBS ISO 6695:2015Cycles Pedal axle and crankassembly with square endfitting Assembly dimensionsBS ISO 6695:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 6695:2015.It supersedes BS 6102-14:1991 which is withdrawn.The UK participati
2、on in its preparation was entrusted to TechnicalCommittee GME/25, Cycles.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctappli
3、cation. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 86129 1ICS 43.150Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee
4、on 31 December 2015.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS ISO 6695:2015 ISO 2015Cycles Pedal axle and crank assembly with square end fitting Assembly dimensionsCycles Axe de pdalier et manivelle emmanchement carr Dimensions dassemblageINTERNATIONAL STANDARDISO6
5、695Second edition2015-12-15Reference numberISO 6695:2015(E)BS ISO 6695:2015ISO 6695:2015(E)ii ISO 2015 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2015, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwis
6、e in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. d
7、e Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 6695:2015ISO 6695:2015(E)Foreword iv1 Scope . 12 Dimensions . 1 ISO 2015 All rights reserved iiiContents PageBS ISO 6695:2015ISO 6695:2015(E)ForewordISO (the Internatio
8、nal Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been
9、established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standar
10、dization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance
11、 with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of a
12、ny patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsemen
13、t.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information.The committee responsible
14、 for this document is ISO/TC 149, Cycles.This second edition cancels and replaces the first edition (ISO 6695:1991), which has been technically revised with the following modifications:a) in Figure 1, illustration of cross section of bottom bracket spindle added;b) in Figure 1, illustration of crank
15、 revised and front-view added;c) in Figure 1, dimensions added and revised;d) in Figure 1 and Table 1, half wedge angle 1/2 added;e) in Table 1, dimensions and tolerances revised and specified;f) editorial changes.iv ISO 2015 All rights reservedBS ISO 6695:2015INTERNATIONAL STANDARD ISO 6695:2015(E)
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
本资源只提供5页预览,全部文档请下载后查看!喜欢就下载吧,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BSISO66952015CYCLESPEDALAXLEANDCRANKASSEMBLYWITHSQUAREENDFITTINGASSEMBLYDIMENSIONS 自行车 中轴 曲柄 配合 装配 尺寸

链接地址:http://www.mydoc123.com/p-587827.html