CSA C22 2 NO 2515 1-2013 Supplemental requirements for extra heavy wall (XW) reinforced thermosetting resin conduit (RTRC) and fittings (First Edition).pdf

1、C22.2 No. 2515.1-13Supplemental requirements for extra heavy wall (XW) reinforced thermosetting resin conduit (RTRC) and fittingsLegal Notice for StandardsCanadian Standards Association (operating as “CSA Group”) develops standards through a consensus standards development process approved by the St

2、andards Council of Canada. This process brings together volunteers representing varied viewpoints and interests to achieve consensus and develop a standard. Although CSA Group administers the process and establishes rules to promote fairness in achieving consensus, it does not independently test, ev

3、aluate, or verify the content of standards.Disclaimer and exclusion of liabilityThis document is provided without any representations, warranties, or conditions of any kind, express or implied, including, without limitation, implied warranties or conditions concerning this documents fitness for a pa

4、rticular purpose or use, its merchantability, or its non-infringement of any third partys intellectual property rights. CSA Group does not warrant the accuracy, completeness, or currency of any of the information published in this document. CSA Group makes no representations or warranties regarding

5、this documents compliance with any applicable statute, rule, or regulation. IN NO EVENT SHALL CSA GROUP, ITS VOLUNTEERS, MEMBERS, SUBSIDIARIES, OR AFFILIATED COMPANIES, OR THEIR EMPLOYEES, DIRECTORS, OR OFFICERS, BE LIABLE FOR ANY DIRECT, INDIRECT, OR INCIDENTAL DAMAGES, INJURY, LOSS, COSTS, OR EXPE

6、NSES, HOWSOEVER CAUSED, INCLUDING BUT NOT LIMITED TO SPECIAL OR CONSEQUENTIAL DAMAGES, LOST REVENUE, BUSINESS INTERRUPTION, LOST OR DAMAGED DATA, OR ANY OTHER COMMERCIAL OR ECONOMIC LOSS, WHETHER BASED IN CONTRACT, TORT (INCLUDING NEGLIGENCE), OR ANY OTHER THEORY OF LIABILITY, ARISING OUT OF OR RESU

7、LTING FROM ACCESS TO OR POSSESSION OR USE OF THIS DOCUMENT, EVEN IF CSA GROUP HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, INJURY, LOSS, COSTS, OR EXPENSES.In publishing and making this document available, CSA Group is not undertaking to render professional or other services for or on behalf

8、 of any person or entity or to perform any duty owed by any person or entity to another person or entity. The information in this document is directed to those who have the appropriate degree of experience to use and apply its contents, and CSA Group accepts no responsibility whatsoever arising in a

9、ny way from any and all use of or reliance on the information contained in this document. CSA Group is a private not-for-profit company that publishes voluntary standards and related documents. CSA Group has no power, nor does it undertake, to enforce compliance with the contents of the standards or

10、 other documents it publishes. Intellectual property rights and ownershipAs between CSA Group and the users of this document (whether it be in printed or electronic form), CSA Group is the owner, or the authorized licensee, of all works contained herein that are protected by copyright, all trade-mar

11、ks (except as otherwise noted to the contrary), and all inventions and trade secrets that may be contained in this document, whether or not such inventions and trade secrets are protected by patents and applications for patents. Without limitation, the unauthorized use, modification, copying, or dis

12、closure of this document may violate laws that protect CSA Groups and/or others intellectual property and may give rise to a right in CSA Group and/or others to seek legal redress for such use, modification, copying, or disclosure. To the extent permitted by licence or by law, CSA Group reserves all

13、 intellectual property rights in this document.Patent rightsAttention is drawn to the possibility that some of the elements of this standard may be the subject of patent rights. CSA Group shall not be held responsible for identifying any or all such patent rights. Users of this standard are expressl

14、y advised that determination of the validity of any such patent rights is entirely their own responsibility.Authorized use of this documentThis document is being provided by CSA Group for informational and non-commercial use only. The user of this document is authorized to do only the following:If t

15、his document is in electronic form:sLOADTHISDOCUMENTONTOACOMPUTERFORTHESOLEPURPOSEOFREVIEWINGITsSEARCHANDBROWSETHISDOCUMENTANDsPRINTTHISDOCUMENTIFITISIN0$(b) provide an explanation of circumstances surrounding the actual field condition; and(c) where possible, phrase the request in such a way that a

16、 specific “yes” or “no” answer will address the issue.Committee interpretations are processed in accordance with the CSA Directives and guidelines governing standardization and are available on the Current Standards Activities page at standardsactivities.csa.ca.(5) This Standard is subject to review

17、 five years from the date of publication. Suggestions for its improvement will be referred to the appropriate committee. To submit a proposal for change, please send the following information to inquiriescsagroup.org and include “Proposal for change” in the subject line:(a) Standard designation (num

18、ber);(b) relevant clause, table, and/or figure number;(c) wording of the proposed change; and(d) rationale for the change. 2013 CSA GroupSupplemental requirements for extra heavy wall (XW)reinforced thermosetting resin conduit (RTRC) and fittingsNovember 2013 1C22.2 No. 2515.1-13Supplemental require

19、ments for extra heavy wall (XW) reinforced thermosetting resin conduit (RTRC) and fittings1Scope1.1 Objective1.1.1This Standard contains requirements for reinforced thermosetting resin conduit (RTRC) of the extra heavy wall type (XW) in trade sizes 3/4-6 (metric designators 21-155).1.1.2Products cov

20、ered by this Standard are intended to be installed in accordance with the Canadian Electrical Code, Part I and General Requirements Canadian Electrical Code, Part II, CAN/CSA-C22.2 No. 0.1.1.3The requirements in this Standard supplement the requirements contained in CSA C22.2 No. 2515.1.2 Terminolog

21、yIn this Standard “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is perm

22、issible within the limits of the standard.Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material.Notes to tables and figures are considered part of the table or f

23、igure and may be written as requirements.Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.1.3 Units of measurementThe values given in SI are the units of record for the purposes of this Standard. The values given in parenthesis are for informati

24、on and comparison only.2 Reference publicationsThis Standard refers to the following publications, and where such reference is made, it shall be to the edition listed below. Such reference shall include all amendments published up to the time this referencing Standard was approved.C22.2 No. 2515.1-1

25、3 2013 CSA Group2 November 2013CSA GroupC22.1-12Canadian Electrical Code, Part I (CE Code)CAN/CSA-C22.2 No. 0-10General requirements Canadian Electrical Code, Part IIC22.2 No. 2515-09Aboveground reinforced thermosetting resin conduit (RTRC) and fittings3 Construction3.1 GeneralConduit shall comply w

26、ith Clause 4.1 of CSA C22.2 No. 2515.3.2 Conduit with an integral belled endThe dimensions of conduit with an integral coupling on one end shall be in accordance with Tables 1 and 2. They shall also meet the requirements of Clause 5.7 of CSA C22.2 No. 2515.3.3 CouplingsCouplings shall be straight wi

27、th belled ends or 5 degree angle couplings. Dimensions of couplings shall be in accordance with Tables 3 and 4. Couplings shall also meet the requirements of Clause 5.7 of CSA C22.2 No. 2515.4Tests4.1 General XW conduit and fittings shall comply with the applicable requirements of Clause 5 of CSA C2

28、2.2 No. 2515, except as detailed in Clauses 4.2 and 4.3.4.2 Compression for type XW conduitXW conduit shall be tested in accordance with Clause 5.2 of CSA C22.2 No. 2515, except that a force of 8900 N (2000 lb) shall be used for all sizes. The internal diameter of XW conduit shall not decrease by mo

29、re than 25% during application of the force, and the conduit shall show no evidence of cracking or buckling after removal from the compression machine when examined with normal or corrected to normal vision.4.3 Impact resistance for type XW conduitXW conduit shall be tested in accordance with Clause

30、 5.4 of CSA C22.2 No. 2515, except that(a)the impact tup shall have a weight of 34.1 kg and a diameter of 150 mm;(b) the impact energy shall be as specified in Table 5; and(c) testing and sample conditioning shall be performed at a temperature of 23 2 C. 2013 CSA GroupSupplemental requirements for e

31、xtra heavy wall (XW)reinforced thermosetting resin conduit (RTRC) and fittingsNovember 2013 35 Markings5.1All of the markings described in Clauses 5.2 and 5.3 shall be clearly legible and durable. Additional markings may be used if they do not conflict with the markings described in Clauses 5.2 and

32、5.3, and comply with Clause 4.1 of CSA C22.2 No. 2515.5.2The outer surface of every straight length of conduit, and every elbow and other bend made from and for use with such conduit, shall be marked in accordance with Clause 6.2 of CSA C22.2 No. 2515, with the following exceptions:(a) “XW” to repla

33、ce “SW” or “HW” marking; and(b) “IPS” or “ID” marking is optional.5.3The outer surfaces of conduit and elbows, fittings, and conduit bodies that are intended for wetting by reagents per Clause 5.6 of CSA C22.2 No. 2515 shall be marked “RESISTANT TO THE FOLLOWING REAGENTS (followed by the name of the

34、 specific reagents and temperature limitations)”.Table 1Conduit dimensions IPS Type XW(See Clause 3.2.)*Measured circumferentially.Trade sizeMetric designatorMinimum inside diameter, mmWall thickness, mm Outside diameter*, mmMinimum Maximum Minimum Maximum3/4 21 22.61 5.59 6.73 35.31 36.581 27 29.34

35、 5.59 6.73 42.04 43.311-1/4 35 38.10 5.59 6.73 50.80 52.071-1/2 41 44.20 5.59 6.73 56.90 58.17C22.2 No. 2515.1-13 2013 CSA Group4 November 2013Table 2Conduit dimensions ID Type XW(See Clause 3.2.)*Measured circumferentially.Table 3Dimensions for couplings IPS Type XW(See Clause 3.3.)Table 4Dimension

36、s for couplingsID Type XW(See Clause 3.3.)Trade sizeMetric designatorMinimum inside diameter, mmWall thickness, mm Outside diameter*, mmMinimum Maximum Minimum Maximum2 53 50.29 5.59 6.73 62.99 64.262-1/2 63 63.00 5.59 6.73 75.69 76.963 78 75.69 5.59 6.73 88.39 89.663-1/2 91 88.39 5.59 6.73 101.10 1

37、02.364 103 101.09 5.59 6.73 113.79 115.065 129 126.24 5.59 6.73 138.94 140.466 155 151.64 5.59 6.73 164.34 165.86Trade sizeMetric designatorMinimum socket depth, mmMinimum inside diameter of socket, mmMinimum socket wall thickness, mm3/4 21 50.80 35.69 5.591 27 50.80 42.42 5.591-1/4 35 50.80 51.18 5

38、591-1/2 41 50.80 57.28 5.59Trade sizeMetric designatorMinimum socket depth, mmMinimum inside diameter of socket, mmMinimum socket wall thickness, mm2 53 50.80 63.37 5.592-1/2 63 50.80 76.07 5.593 78 50.80 88.77 5.593-1/2 91 50.80 101.47 5.594 103 57.15 114.17 5.595 129 74.68 139.57 5.596 155 74.68

39、164.97 5.59 2013 CSA GroupSupplemental requirements for extra heavy wall (XW)reinforced thermosetting resin conduit (RTRC) and fittingsNovember 2013 5Table 5Impact resistance Type XW(See Clause 4.3.)Trade size Metric designator Impact energy, J3/4 21 1271 27 2031-1/4 35 2291-1/2 41 2552 53 4072-1/2

40、63 5093 78 7123-1/2 91 7124 103 7125 129 7126 155 712PRINTED IN CANADAIMPRIMEAU CANADA100%ISBN 978-1-77139-432-1CSA Group prints its publications on Rolland Enviro100, which contains 100% recycled post-consumer fibre, is EcoLogo and Processed Chlorine Free certified, and was manufactured using biogas energy.