DIN 51604-1-1982 FAM testing fluid for polymer materials Composition and requirements《聚合材料用FAM检验液 成分和要求》.pdf

1、UDC 665.733 : 665.753 : 001.4 ! 620.193.471.2 : 678.7 DEUTSCHE NORM November 1982 FAM testing fluid for polymer materials Composition and requirements I 51 604 Part 1 FAM-Prff Issigkeit fr Polymenverkstoffe; Zusammensetzung und Anforderungen Supersedes April 1977 edition As it is current practice in

2、 standards published bv the International Organization for Standardization (/SO), the comma has been used throughout as a decimal marker. 1 Scope and field of application The FAM testing fluidl), 2) is used, unless otherwise specified in decrees and their associated technical rules, for testing poly

3、mer materials, e.g. elastomer materials, plastics components and coatings in automobile construc- tion and in mineral oil distribution systems which come into intensive contact with motor fuels. The test standards for polymer materials, e.g. DIN 53 476 and DIN 53 521 shall be taken into account when

4、 using the FAM testing fluid. Note 1. The FAM testing fluid corresponds neither to a motor fuel commercially available at the time this standard was prepared, nor to any motor fuel anticipated for the future. It can be considered as a testing fluid intended to assess the behaviour of polymer materia

5、ls with regard to the swelling and extraction effect and changes in hardness, malle- ability and strength properties under the action of motor fuels. Note 2. If required, the FAM testing fluid may be tested by an official test house, for example the Bunes- anstalt fur Materialprfung, Unter den Eiche

6、n 87, D-1000 Berlin 45. 2 Concept The FAM testing fluid is a mixture prepared for testing purposes which shall conform with the composition specified in clause 4 and with the requirements specified in clause 5. 3 Designation Designation of the FAM testing fluid (A): FAM testing fluid DIN 51 604 - A

7、4 Composition 4.1 50% by volume pure toluene complying with DIN 51 633. 4.2 30% by volume isooctane2) (2,2,4-trimethyl- penthane) complying with the ASTM manual for rating motor, Diesel and aviation fuels 3). 4.3 15% by volume commercial diisobutylene2) ( 2,4,4-tr i methyl- 1 -pente ne and 2,2,4-tri

8、me thyl-2-pentene1, c8 olefin mixture (alkene mixture) with at least a 98% by volume of c8 olefins (alkenes) consisting of a) at least 85 % by volume 2,4,4-trimethylpentenes, and b) further structural isomers, predominantly dimethyl- hexenes. Density at 15 OC: i5 = 0,720 to 0,724 g/ml. Refractive in

9、dex at 20C: riso = 1,409 to 1,411. Distillation range: initial boiling point: 98 OC minimum; final boiling point: 1 10C maximum. 4.4 5 % by volume reagent grade ethanol. 5 Requirements 5.1 Density at 15OC: pi5 = 0,789 to 0,793g/ml, deter- mined in accordance with DIN 51 757. 5.2 Refractive index at

10、20 OC: = 1,445 to 1,446, determined in accordance with DIN 51 423 Part 2. 6 Safety notes Any safety regulations or decrees valid at the appropriate time shall be taken into consideration when using the FAM testing fluid, e.g. Verordnung ber Anlagen zur Lagerung, Ab fllung und Befrderung brennbarer F

11、lssig- keiten (Decree on the storage, transfer and transportation of combustible liquids), Verordnung ber gefhrliche Arbeifssfoffe (Decree on dangerous materials). 1) FAM means Fachausschuss Minerall- und Brennstoff- normung (Mineral oil and fuels standards special committee). 2) Information regardi

12、ng sources of supply: DIN-Bezugs- quellen fr normgerech fe Erzeugnisse of DIN Deutsches Institut fr Normung e. V., Burggrafenstrasse 4-10, D-1000 Berlin 30. 3) Obtainable from the Auslandsnormenvermittlung of DIN Deutsches Institut fr Normung e. V., Burggrafen- Strasse 4-10, D-1000 Berlin 30. Contin

13、ued on page 2 Soiesale right. of German Standards (DIN-Nomen) are wlth Beuth verlag mbn. Berlin 30 01.84 DIN 51 604 Part 1 Engl. Price group 5 Sales No. 0105 Page 2 DIN 51 604 Part 1 Standards referred to and other documents DIN 51 423 Part 2 DIN 51 633 DIN 51 757 DIN 51 848 Part 1 DIN 53476 DIN 535

14、21 Verordnung ber Anlagen zur Lagerung, Abfllung und Befrderung brennbarer Flssigkeiten Verordnung ber gefhrliche A rbeitsstoffe ASTM manual for rating motor, Diesel and aviation fuels Testing of mineral oils; measurement of the refractive index using the Abbe refractometer Benzene and benzene homol

15、ogues; requirements Testing of mineral oils and related materials; determination of density Testing of mineral oils; accuracy of test methods; general, concepts and their application to mineral oil standards including requirements Testing of plastics; determination of reaction to fluids Testing of r

16、ubbers and elastomers; determination of reaction to fluids, vapours and gases Other relevant standards DIN 51 604 Part 2 DIN 51 604 Part 3 (at present at the stage of draft) FAM testing fluid containing methanol, for polymer materials; composition and requirements (at present at the stage of draft)

17、FAM testing fluid with methanol mixtures, for polymer materials; composition and requirements Previous editions DIN 51 604 Part 1 : 04.77 Amendments The text of the April 1977 edition has been revised taking the specifications of DIN 1310 into consideration. Explanatory notes This standard was prepa

18、red by Technical Committee Anforderungenan flssige Kraftstoffe of Special Committee Minerall- und Brennstoffnormung of the Normenausschuss Materialprfung (Materials Testing Standards Committee) in cooperation with Working Group Einheitliche Prfverfahren fr Membranwerkstoffe and the Koordinierungsgre

19、mium fr Prfmethoden ber das Verhalten von flssigen Medien gegenber Elastomeren of the Deutsche Gesellschaft fr Minerallwissenscha ft und Kohle-Chemie e. V. (German society for mineral oil science and coal chemistry). Commercially available motor fuels can contain small quantities of water and occasi

20、onally alcohol admixtures which can be detrimental to certain hydrolysis-sensitive polymer materials in long-term use. It cannot be expected that these circumstances are fully revealed in every case by the ethanol and water content of the FAM testing fluid at test temper- atures and durations normally employed. Thus, in order to avoid long-term tests, the use of other methods of test in- tended to demonstrate this is recommended for polymer materials sensitive in this respect. International Patent Classification G O1 N 33/44