DIN 5406-2011 Rolling bearings - Lockwashers Safety plate Lockclip《滚动轴承 锁紧垫圈 止动钩安全平垫圈》.pdf

1、April 2011 Translation by DIN-Sprachendienst.English price group 9No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 2

2、1.060.30!$pA“1773004www.din.deDDIN 5406Rolling bearings Lockwashers and locking clips for use with locknutsEnglish translation of DIN 5406:2011-04Wlzlager Muttersicherungen; Sicherungsblech, SicherungsbgelEnglische bersetzung von DIN 5406:2011-04Roulements Dispositifs de blocage; ondelles-frain, tta

3、ches de blocageTraduction anglaise de DIN 5406:2011-04SupersedesDIN 5406:2009-05www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.1404.11r aDIN 5406:2011-04 A comma is used as the decimal marker. Contents Page Foreword. 3 1 Scope . 4

4、 2 Normative references . 4 3 Symbols . 4 4 Type, designations, dimensions . 5 4.1 General. 5 4.2 Types 5 4.3 Designation . 6 4.4 Dimensions, symbols. 6 5 Material 11 6 Design 11 7 Mounting 12 Annex A (informative) Explanatory notes 13 Bibliography . 14 Figures Figure 1 Dimensions of MB . . and MBL

5、. . lockwashers (notation) 5 Figure 2 Dimensions of MS . . locking clip assembly (notation). 5 Figure 3 Lockwasher on DIN 5415 adapter sleeve. 12 Figure 4 Locking clip on DIN 5415 adapter sleeve 12 Figure 5 Groove dimensions when directly locked to shaft. 12 Tables Table 1 Dimensions and symbols for

6、 lockwashers MB . . and MBL . . 7 Table 2 Dimensions and symbols for locking clips MS . . 9 2 DIN 5406:2011-04 Foreword This standard has been prepared by Working Committee NA 118-01-02 AA Kugellager und Spannlager einschlielich Teile, allgemeines Wlzlagerzubehr und Gehuse of the Normenausschuss Wlz

7、- und Gleitlager (Rolling Bearings and Plain Bearings Standards Committee). Amendments This standard differs from DIN 5406:1993-02 as follows: a) the standard has been editorially revised; b) information on masses has been deleted from Tables 1 and 2; c) types have been added by analogy with ISO 298

8、2-2; d) symbols have been largely brought into line with ISO 2982-2; e) further information on design has been added; f) the normative references have been updated. This standard contains the following corrections to DIN 5406:2009-05: a) The shaft groove width b3and the associated width of inner tab

9、 b2for bore diameters d1from 160 mm to 280 mm have been corrected. Previous editions DIN 5406: 1973-01, 1977-04, 1993-02, 2009-05 3 DIN 5406:2011-04 1 Scope This standard specifies dimensions and symbols for locking devices intended to be used with locknuts. Locking devices in accordance with this s

10、tandard are lockwashers and locking clips for use with locknuts conforming to DIN 981. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of

11、 the referenced document (including any amendments) applies. DIN 981, Rolling bearings Locknuts DIN 5415, Rolling bearings Adapter sleeves DIN ISO 13715, Technical drawings Edges of undefined shape Vocabulary and indication on drawings 3 Symbols For the purposes of this document, the following symbo

12、ls apply. Symbols for the lockwasher: 1b2b1d2d3dWidth of outer tab Width of inner tab Bore diameter External diameter Root diameter of outer tab M Clear width to inner tab N Minimum number of outer tabs s Material thickness Symbols for the locking clip assembly: 1b5de2G1hlWidth of locking clip Diame

13、ter of hole in locking clip Inner width of locking clip Designation of screw thread Height of locking clip Screw length s Material thickness Symbols for the shaft groove: Groove width Groove depth 3bt4 DIN 5406:2011-04 4 Type, designations, dimensions 4.1 General The designs shown are for illustrati

14、ve purposes only; however, the dimensions of lockwashers and locking clips shall be as specified. 4.2 Types A distinction is made between the locking elements as follows: a) Lockwashers (see Figure 1) MB . . Design for type KM and HM . . T locknuts. MBL . . Identical with MB, but diameters d2and d3a

15、re reduced. b) Locking clip (see Figure 2) MS . . Design for type HM locknuts. Figure 1 Dimensions of MB . . and MBL . . lockwashers (notation) Figure 2 Dimensions of MS . . locking clip assembly (notation) 5 DIN 5406:2011-04 6 4.3 Designation Designation of a lockwasher with d1= 120 mm bore diamete

16、r, d2= 164 mm external diameter and d3= 138 mm root diameter of outer tab (symbol MB 24) for use with DIN 981 KM 24 locknut: Lockwasher DIN 5406 MB 24 Designation of a lockwasher with the same d1= 120 mm bore diameter, but reduced d2 = 151 mm external diameter and reduced d3 = 135 mm root diameter o

17、f outer tab (symbol MBL 24) for use with DIN 981 KML 24 locknut: Lockwasher DIN 5406 MBL 24 Designation of a locking clip with fixing screw and securing element (symbol MS 3060) for use with DIN 981 HM 3060 locknut: Locking clip DIN 5406 MS 3060 4.4 Dimensions, symbols Types MB . . and MBL . . accor

18、ding to Table 1. Type MS . . according to Table 2. DIN 5406:2011-04 Table 1 Dimensions and symbols for lockwashers MB . . and MBL . . Dimensions in millimetres Shaft grooveb1d 2d 3d 1b Na2b M s 3b t Symbol Type of suitable DIN 981 locknut 010 021 013,5 09 008,5 MB 0 KM 0 012 025 017,0 03 03 010,5 04

19、 MB 1 KM 1 015 028 021,0 013,5 MB 2 KM 2 017 032 024,0 015,5 MB 3 KM 3 020 036 026,0 04 11 04 018,5 1,00 05 2 MB 4 KM 4 025 042 032,0 023,0 3 MB 5 KM 5 030 049 038,0 05 027,5 06 MB 6 KM 6 035 057 044,0 05 032,5 MB 7 KM 7 040 062 050,0 037,5 MB 8 KM 8 045 069 056,0 042,5 MB 9 KM 9 050 074 061,0 06 13

20、 06 047,5 1,25 07 MB 10 KM 10 055 081 067,0 052,5 MB 11 KM 11 060 086 073,0 057,5 MB 12 KM 12 065 092 079,0 07 062,5 4 MB 13 KM 13 070 098 085,0 066,5 MB 14 KM 14 075 104 090,0 08 071,5 1,50 09 MB 15 KM 15 080 112 095,0 076,5 MB 16 KM 16 085 119 102,0 08 081,5 MB 17 KM 17 090 126 108,0 086,5 MB 18 K

21、M 18 095 133 113,0 10 091,5 11 MB 19 KM 19 100 142 120,0 10 096,5 5 MB 20 KM 20 105 145 126,0 100,5 MB 21 KM 21 110 154 133,0 105,5 1,75 MB 22 KM 22 115 159 137,0 12 110,5 14 6 MB 23 KM 23 120 151 135,0 MBL 24 KML 24 120 164 138,0 115,0 MB 24 KM 24 125 170 148,0 120,0 MB 25 KM 25 130 161 145,0 MBL 2

22、6 KML 26 130 175 149,0 12 125,0 MB 26 KM 26 135 185 160,0 14 17 14 130,0 2,00 16 7 MB 27 KM 27 7 DIN 5406:2011-04 Table 1 (concluded) Dimensions in millimetres Shaft grooveb 1d 2d 3d 1b Na 2b M s 3b t Symbol Type of suitable DIN 981 locknut 140 171 155 12 MBL 28 KML 28 140 192 160 135,0 MB 28 KM 28

23、145 202 171 140,0 MB 29 KM 29 150 188 170 MBL 30 KML 30 150 205 171 14 17 145,0 2,0 7 MB 30 KM 30 155 212 182 16 16 147,5 18 9 MB 31 KM 31 160 199 180 14 MBL 32 KML 32 160 217 182 154,0 8 MB 32 KM 32 165 222 193 157,5 9 MB 33 KM 33 170 211 190 MBL 34 KML 34 170 232 193 18 164,0 20 MB 34 KM 34 180 22

24、1 200 16 MBL 36 KML 36 180 242 203 18 174,0 MB 36 KM 36 190 231 210 16 MBL 38 KML 38 190 252 214 184,0 MB 38 KM 38 200 248 222 MBL 40 KML 40 200 262 226 18 20 194,0 2,5 22 8 MB 40 KM 40 220 292 250 213,0 MB 44 HM 44 T 240 312 270 20 24 233,0 26 MB 48 HM 48 T 260 342 300 253,0 MB 52 HM 52 T 280 362 3

25、20 24 19 28 273,0 3,0 30 9 MB 56 HM 56 T aMinimum number of outer tabs for 4-slot locknuts. N is always to be an odd number. bSee Figure 5. 8 DIN 5406:2011-04 Table 2 Dimensions and symbols for locking clips MS . . Dimensions in millimetres Suitable hexagon screw Shaft groove 1b 1h e 5d s lG 23b t S

26、ymbol Type of suitable DIN 981 locknut 20 12 13,5 07 4 M 6 12 MS 3044 HM 3044 20 12 17,5 09 4 M 8 16 20 MS 3048 HM 3048, HM 3052 24 12 17,5 09 4 M 8 16 MS 3056 HM 3056 24 12 20,5 09 4 M 8 16 MS 3060 HM 3060 24 12 30,5 12 4 M 10 20 07,5 MS 3160 HM 3160 24 15 21,0 09 5 M 8 16 MS 3064 HM 3064, HM 3068

27、24 15 31,0 12 5 M 10 20 24 MS 3164 HM 3164 28 15 38,0 14 5 M 12 25 MS 3168 HM 3168, HM 3172 28 15 20,0 09 5 M 8 16 MS 3072 HM 3072 28 15 24,0 12 5 M 10 20 28 MS 3076 HM 3076, HM 3080 32 15 40,0 14 5 M 12 25 MS 3176 HM 3176 32 15 45,0 18 5 M 16 30 MS 3180 HM 3180, HM 3184 32 15 24,0 12 5 M 10 20 MS 3

28、084 HM 3084 32 15 28,0 14 5 M 12 25 32 MS 3088 HM 3088, HM 3092 36 15 43,0 18 5 M 16 30 MS 3188 HM 3188, HM 3192 36 15 28,0 14 5 M 12 25 MS 3096 HM 3096, HM 30/500 36 15 53,0 18 5 M 16 30 36 MS 3196 HM 3196 40 15 45,0 18 5 M 16 30 09,0 MS 31/500 HM 31/500 40 21 34,0 18 7 M 16 30 MS 30/530 HM 30/530,

29、 HM 30/600 40 21 51,0 22 7 M 20 40 MS 31/530 HM 31/530 40 21 29,0 18 7 M 16 30 40 MS 30/560 HM 30/560 45 21 54,0 22 7 M 20 40 MS 31/560 HM 31/560, HM 31/600 45 21 34,0 18 7 M 16 30 MS 30/630 HM 30/630 45 21 39,0 18 7 M 16 30 45 MS 30/670 HM 30/670 50 21 61,0 22 7 M 20 40 MS 31/630 HM 31/630 50 21 66

30、,0 22 7 M 20 40 12,0 MS 31/670 HM 31/670 50 21 39,0 18 7 M 16 30 50 MS 30/710 HM 30/710 55 21 69,0 26 7 M 24 50 MS 31/710 HM 31/710 55 21 39,0 18 7 M 16 30 55 13,0 MS 30/750 HM 30/750, HM 30/800 9 DIN 5406:2011-04 10 Suitable hexagon screw Shaft groove 1b 1h e 5d s lG 23b t Symbol Type of suitable D

31、IN 981 locknut 60 21 70 26 7 M 24 50 MS 31/750 HM 31/750, HM 31/800 60 21 44 22 7 M 20 40 60 MS 30/850 HM 30/850, HM 30/900 70 21 71 26 7 M 24 50 MS 31/850 HM 31/850 70 21 76 26 7 M 24 50 70 MS 31/900 HM 31/900 60 21 46 22 7 M 20 40 60 MS 30/950 HM 30/950 70 21 78 26 7 M 24 50 70 MS 31/950 HM 31/950

32、 60 21 51 22 7 M 20 40 60 MS 30/1000 HM 30/1000, HM 30/1060 70 21 88 26 7 M 24 50 70 13 MS 31/1000 HM 31/1000 Dimensions in millimetres Table 2 (concluded) DIN 5406:2011-04 5 Material Lockwashers and locking clips shall be made from steel with a minimum tensile strength of 300 N/mm2, with the method

33、 of manufacture being at the manufacturers discretion. The screw material shall be at the manufacturers discretion. 6 Design The following tolerances shall apply for lockwashers: a) Bore diameter, d1: Tolerance zone C11; b) External diameter, d2: Tolerance zone js17; c) Root diameter of outer tab, d

34、3: Tolerance zone h13; d) Tab widths, b1and b2: Tolerance zone a15; e) Clear width, M: Tolerance zone C11; f) Material thickness, s: Table 1 gives preferred values; minor deviations are permitted; g) Workpiece outer edges: Burrs are not permitted, “(-)” according to DIN ISO 13715. The following tole

35、rances shall apply for locking clips: a) Clip width, b1: Tolerance zone a15; b) Clip height, h1: Tolerance zone js16; c) Inner width, e: Tolerance zone H13; d) Diameter of hole in locking clip, d5: Tolerance 0,5 mm; e) Material thickness, s: Table 2 gives preferred values; minor deviations are permi

36、tted; f) Workpiece outer edges: Burrs are not permitted, “(-)” according to DIN ISO 13715; 11 DIN 5406:2011-04 g) Fixing screws and securing elements: at manufacturers discretion. The following tolerances shall apply for shaft grooves: a) Groove width, b3: Tolerance zone H11; b) Groove depth, t: Tol

37、erance 0 mm to +0,5 mm. 7 Mounting Details of mounting are shown in Figures 3, 4 and 5. Figure 3 Lockwasher on DIN 5415 adapter sleeve Figure 4 Locking clip on DIN 5415 adapter sleeve Dimensions according to Tables 1 and 2 Figure 5 Groove dimensions when directly locked to shaft 12 DIN 5406:2011-04

38、Annex A (informative) Explanatory notes Lockwashers according to this standard largely conform to ISO 2982-2. This standard differs from ISO 2982-2:2001 in the following aspects: a) Tables 1 and 2 of this standard only show dimensions for the locking elements of locknuts according to DIN 981. b) Thi

39、s standard also includes the symbols for the locking elements that have been successfully used in practice. c) The dimensions for the relevant locknuts are given in a separate standard (see DIN 981); only the designation of the matching locknuts is included in the tables. d) This standard also conta

40、ins specifications for materials and tolerances. e) Figures 3 and 4 show details of mounting lockwashers and locking clips, and Figure 5 shows the groove dimensions for direct locking on the shaft, which is not contained in ISO 2982-2. 13 DIN 5406:2011-04 14 Bibliography DIN 5418, Rolling bearings Dimensions for mounting ISO 2982-1, Rolling bearings Accessories Part 1: Tapered sleeves Dimensions ISO 2982-2, Rolling bearings Accessories Part 2: Locknuts and locking devices Dimensions